• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.1
• /
• pp.62-66
• /
• 2011

In this study, the thermal performance of disk can be compared with disk and disk with holes through numerical analysis. The capacity of thermal emission on general disk becomes more than on disk with holes at the distribution of temperature at first and the magnitude of equivalent stress on general disk becomes less than on disk with holes at the distribution of stress. The capacity of thermal emission or the magnitude of thermal deformation on disk with holes becomes less than that on general disk 30 minutes later. The disk with holes is worn less and more durable than general disk. The performance of cooling and braking force at disk and pad can be improved by installing the disk with holes.

• Tribology and Lubricants
• /
• v.30 no.4
• /
• pp.240-245
• /
• 2014

Low alloy heat resistant brake disk and sintered brake pad are applied to mechanical brake system for the speed-up of urban rapid transit. In this research, we analyzed how the frictional characteristics between brake disk and pad are influenced by the disk mass. At a high disk mass, the friction stability was the lower value as a result of the lack of tribofilm formation at the disk surface. Wear rates of friction materials showed the higher value at a low disk mass and wear rates of 10 mm and 15 mm showed the similar level. Average friction coefficient was the lower value at the 10 mm disk thickness and range of variation of average friction coefficient was also the smaller value at the 10 mm disk thickness. However, there were no significant changes in the friction coefficients under any of test conditions. Surface roughness of a disk showed the highest value at the 5 mm disk and surface roughnesses of 10 mm and 15 mm showed the similar level. As a result, friction characteristics of disk mass influenced the friction stability, as well as the wear rate of friction pad and disk, but not the friction coefficient.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.88-95
• /
• 2005

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated in HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted panicles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.2
• /
• pp.123-129
• /
• 2006

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated ill HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted particles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.206-210
• /
• 1998

A study on dynamic characteristics of rotating disks in magneto optical disk drives is presented. Natural frequencies of rotating disks are investigated experimentally and numerically. The frequency response and critical speeds of the ASMO disk are discussed. The characteristics of airflow around the disk and their effects on disk vibrations are also investigated. It is found that the numerical calculation of the natural frequencies of rotating disks agrees well with the experimental results. The airflow around the disk in the cartridge affects the characteristics of the disk vibrations to reduce the modal frequencies of the disk. The experiment shows that negative vertical offsets of the disk in the cartridge possibly increase the vibration amplitudes. As being influenced by the geometry of the cartridge, the rotation of the disk causes an asymmetric airflow in the presence of window.

• Tribology and Lubricants
• /
• v.22 no.2
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.175-185
• /
• 2004

Rotating disks are used in various machines such as data storage device, gyroscope, circular saw, etc. Transverse vibration of a rotating disk is very important for the performance of these machines. This work proposes a method to suppress transverse vibration of a very flexible rotating disk in non-contacting manner. A system considered in this study is a very flexible rotating disk with a thrust bearing pad which is located underneath the rotating disk. The pressure force generated in the gap between the rotating disk and the thrust pad pushes the rotating disk in the direction of axis of rotation while the centrifugal force and the elastic recovery force push the rotating disk in reverse direction. The balance between these forces suppresses the transverse vibration of the rotating disk. A coupled disk-fluid system is analyzed numerically. The finite element method is used to compute the pressure distribution between the thrust pad and the rotating disk while the finite difference method is used to compute the transverse vibration of a rotating disk. Results show that the transverse vibration of the rotating disk can be suppressed effectively for certain combination of air bearing and operating parameters.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.28-36
• /
• 1998

This paper presents the thermal behaviours of a solid type disk brake for a high-speed train. The thermal behaviours of a brake disk with 50mm thickness shows good performance compared with 45mm thickness of a disk because of a high specific heat capacity. The FEM results show that the thickness of the disk with a same weight of the brake disk should be increased for a good flexibility of the contact thermal problems. Therefore, the ratio between the pad and disk in diameter may be reduced and the thickness of a disk increased.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1130-1135
• /
• 2001

This paper investigated the dynamic performance of HDD disk-spindle system to reduce disk fluttering. Rocking frequencies of the disk-spindle system and radial NRRO are measured to escape the ball defect frequencies and to determine the relative optimal position of the disk in the motor. It was found that disk fluttering was reduced by increasing disk thickness, inserting viscoelastic material between the disk and the spacer and decreasing the gap between the disk and the base.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.539-542
• /
• 2002

The role of disk clamp is to fasten disks to motor and to prevent the slip of disks during operation. This paper examined the effects of the design parameters of disk clamp - thickness, contact radius and cross-sectional shape -on the clamping force and circumferential stress distribution of disk. The large stress variation in circumferential direction results in large disk waveness and will increase repeatable run-out (RRO) finally. The disk clamp-disk-disk spacer system is modeled and the FE analysis is performed by ANSYS. The disk clamp with large contact radius shows more uniform stress distribution than the one with small contact radius and the stiffness variation around circumferential direct ion or the addition of the bending sect ion can make stress distribution uniform.