• Journal of Power Electronics
• /
• 제12권1호
• /
• pp.49-57
• /
• 2012

This paper presents performance evaluation of an Integrated Starter-Alternator (ISA) prototype with an Interior Permanent Magnet (IPM) synchronous machine under sensor-less operation. To attain a high starting torque at zero speed and in subsequent extremely low speed range, a hybrid signal injection method is proposed. At higher speed, an improved stator flux observer is used for the stator flux estimation. This observer is able to produce accurately-estimated stator flux linkage for high performance Direct Torque and Flux Control (DTFC) implementation. The sensor-less DTFC IPM synchronous machine drive takes full advantage of the capacity of the power converter and fulfills the control specifications for the ISA. The trajectory control algorithm responds rapidly and in a well behaved manner over a wide range of operating conditions. The experimental results verify the feasibility and advantages of the system.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권10호
• /
• pp.555-562
• /
• 2000

We propose an adaptive nonlinear control algorithm for compensation of the stick-slip friction in a dynamic system. The friction force and mass of the system are estimated and compensated by adaptive control law. Especially, as the nonlinear control input in a small tracking error zone is enlarged by the nonlinear function, the steady state error is significantly reduced. The proposed algorithm is a direct adaptive control method based on the Laypunov stability theory, and its convergence is guaranteed under the bounded noise or torque disturbance. We verified the performance of the proposed algorithm by computer simulation on one-DOF mechanical system with friction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2305-2308
• /
• 1998

In this paper, a control algorithm which enables robot to cooperate with human is proposed. The method senses the humanbeing's intention by using force/torque sensor attached at the end effector and moves and cooperates as intended by humanbeing. The method also considers safety of the humanbeing by adjusting and limiting the robot speed automatically. The proposed method is verified its performance by computer simulation and experiments for the 2-DOF DD(Direct Drive) Arm in real-time

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1996년도 창립기념 전력전자학술발표회 논문집
• /
• pp.47-51
• /
• 1996

In this paper, we propose a method for compliance control of a SCARA type 2-freedom direct drive(DD) manipulator. Each joint of the manipulator is driven by a travelling ultrasonic motor(USM). The travelling USM has good some characteristics over conventional servo motors such as compact size, light weight, silent motion, high torque and high speed response. By controlling the elasticity and viscosity of robot joints, a robot can work in compliance with external environment. we control the elastic coefficient and the viscous coefficient of joint by adjusting the phase difference of the motor power. And we contemplate transient response of USM with adjusting the elastic coefficient and the viscous coefficient. To use the result, we can control the robot to reach its goal with compliance motion. It remains for further research to develop the impedance control of USM.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.199-205
• /
• 2012

This paper propose a improved parameter estimations of five-phase squirrel-cage induction motor(IM) for speed control system on field oriented control(FOC). In order to high performance control of ac the motors using a FOC and DTC(direct torque control) algorithm, there are required precise motor parameters for slip calculation, flux observer, controller gain, rotor position and speed estimation, and so on. We are suggest a estimation method of the motor parameters that developing five-phase squirrel-cage IM have a stator of concentrated winding for experimental. There are results of stator winding test, no-load test, locked rotor test, and obtained equivalent circuits using manufactured experimental apparatus. For presenting the superior performance of the speed control system in adapted the parameters, experimental results are presented using a 32-bit fixed point TMS320F2812 DSP with 1.5[KW] IM.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1241-1250
• /
• 2018

Parallel three-phase voltage source inverters in a direct connection configuration are widely used to increase system power ratings. A zero-sequence circulating current can be generated according to the switching method; however, the zero-sequence circulating current not only distorts current, but also reduces the system reliability and efficiency. In this paper, a model predictive control scheme is proposed for parallel inverters to drive an interior permanent magnet synchronous motor with zero-sequence circulating current suppression. The voltage vector of the parallel inverters is derived to predict and control the torque and stator flux components. In addition, the zero-sequence circulating current is suppressed by designing the cost function without an additional current sensor and high-impedance inductor. Simulation and experimental results are presented to verify the proposed control scheme.

• 전력전자학회논문지
• /
• 제12권6호
• /
• pp.483-490
• /
• 2007

본 논문의 목표는 열차의 노선 운행을 모의하여 시뮬레이션 상에서 실제 열차 운행과 똑 같은 실험 결과를 얻을 수 있는 프로그램을 만들어, 이를 이용하여 구동 장치의 특성을 평가하고 에너지 절약에 대한 연구를 하는 것이다. 열차 주행 시뮬레이션은 실제 대전 지하철 노선 데이터를 이용하여 출발역에서부터 네 번째 정차역까지 구현한다. 열차의 구동 에너지를 절약하기 위한 전동기 제어 방식과 발전기의 회생 에너지에 관한 연구를 선택한다. 열차의 추진 장치는 (Space Vector Modulation)SVM - (Direct Torque Control)DTC로 구현된 M-G Set으로 구성하여 열차가 주행 시 전동기에서 소비되는 에너지와 제동 시 발전기에서 발생되는 회생 에너지를 Simplorer 프로그램을 이용하여 시뮬레이션 한다. 시뮬레이션 결과를 통해 열차의 소비 에너지와 회생 에너지를 연구한다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제23권4호
• /
• pp.35-38
• /
• 2021

Conventional direct current (DC) rotating machines are usually used for crane and press machine using high torque in metal and steel industries, because of a constant output power along variable rotating speed. A general DC motor with permanent field magnets could not increase a magnetic flux density at a gap between armature coils and field magnets. However, a superconducting DC motor has field magnets composed with high temperature superconducting (HTS) coils and it could increase the magnetic flux density at the gap to over 10 times than those of a general DC motor by control the excitation current into HTS coils. The superconducting DC motor could be operated with extremely high torque and constant output power at a low rotational speed. In this paper, a 500 W superconducting DC rotating machine was conceptually designed with a LN₂ (Liquid Nitrogen) cooling method and the operation characteristics results of HTS field magnets were presented. The two no-insulation HTS magnets for a 500 W superconducting DC rotating machine were fabricated. The excitation current for the HTS magnets could be controlled from 0 to 40 A. This test results will be available to design large-sized HTS magnets for a number of hundred kW class superconducting DC rotating machine under LN₂ cooling system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권2호
• /
• pp.227-235
• /
• 1999

In this paper a vibration control fo a one-link flexible beam is considered. At first a state-space model for a flexible beam is derived by using the assumed-modes approach. Based on this model the transfer function between the applied torque and the tip deflection fo the beam is presented because it is convenient to apply our method. In general there exist some control difference due to flexibility of the beam so we adop a forward-passive controller to reduce these phenomena. And a complex dual-input describing function compensator is used to control the tip deflection. The stabiltiy and the performance of the closed-loop system are analyzed. Finally the validity of the derived model and the effectiveness of proposed controller are confirmed throuth simula-tions and experiments.

• 전자공학회논문지
• /
• 제52권3호
• /
• pp.206-212
• /
• 2015

본 논문에서는 ITO 터치 패널 센서를 로봇의 피부로 이용하여 로봇 팔을 제어하는 물리적 인간-로봇 상호작용 방법을 제안한다. 사람과 로봇간의 물리적 상호작용을 구현하기 위해서는 힘/토크 센서를 사용하는 방법과 작은 소자 타입의 센서를 배치하여 만든 촉각 센서를 사용하는 방법이 연구되고 있다. 하지만, 이러한 센서들은 가격적인 측면이나 성능적인 측면에서 장단점이 존재하며, 본 연구에서는 터치 패널을 로봇의 피부로 사용하여 물리적 상호작용을 하는 방법을 제안하고 전체적인 시스템을 구축하여 실험을 통해 힘/토크 센서의 정확성과 소자 타입 센서의 경제성을 보이고자 한다. 실험은 터치 패널에서 기준점을 잡아 제스처를 생성하여 로봇 팔을 제어하는 방법과 엔드이펙터에 장착하여 로봇 팔을 제어하는 방법에 대해 진행하였다. 이러한 실험을 통해 터치 패널을 이용한 교시 제어의 가능성도 확인하였다.