• 자원리싸이클링
• /
• 제16권4호
• /
• pp.33-39
• /
• 2007

직류 ESR(Electro Slag Remelting)장치를 이용하여 타이타늄 스크랩의 재용해 및 정련에 관한 기초연구를 수행하였다. 비소모성 양극으로는 흑연봉을, 슬래그로는 $CaF_2-TiO_2$계를 사용하였다. 재용해한 타이타늄 잉곳의 형상 및 산소 함량에 미치는 슬래그 조성의 영향을 검토하였다. $CaF_2-TiO_2$계 슬래그에서는 잉곳 내부에 슬래그의 혼입이 없는 매우 양호한 형상의 타이타늄 잉곳이 형성되었으며, 산소 함량도 타이타늄스크랩보다 낮은 값을 나타내었다. $CaF_2-TiO_2$계 슬래그에 CaO를 첨가한 경우 잉곳 내부에 슬래그가 혼입되었으며, 산소 농도도 Ti 스크랩 보다 높은 값을 나타내었다.

• Journal of Welding and Joining
• /
• 제25권6호
• /
• pp.71-77
• /
• 2007

Until now, many researches on laser-arc hybrid welding processes have been conducted mainly for high power CW laser and high direct current arc to weld the thick steel plates for shipbuilding. Recently, however the usage of thin steel plates, which tend to be deformed easily by thermal energy, is been increasing because of demand of light structure such as car body in the automobile industry. Accordingly, heat sources having relatively low heat input such as pulsed laser, dip-transfer DC GMA and pulsed GMA seem to be applied more increasingly and the study about those heat sources is needed more intensively. Any heat source mentioned above can not stand alone without weld defects at a relatively high welding speed for increasing the welding productivity. This is main reason to apply the hybrid welding process which uses pulsed laser and low-heat-input GMA heat sources simultaneously to weld the thin steel plate. In this study, parameters of pulsed laser and dip-transfer DC GMA welding are studied firstly through preliminary experiments, and then analyzed in the viewpoint of their physical phenomena. Before conducting the hybrid welding, a pulse control technique is developed based on the parallel port communication and Visual C++ 6.0. Owing to development of this technique, interactions of laser and arc pulses can be controlled consistently. Using the pulse control technique, the hybrid welding is conducted and then its interactive welding phenomenon is analyzed.

• Journal of the Korean Physical Society
• /
• 제81권
• /
• pp.867-875
• /
• 2022

This paper explored the effect of deposition conditions on the characteristics of copper oxide (CuO_x) thin films prepared by direct current (DC) magnetron sputtering. X-ray diffraction exhibited that CuO with n-type conductivity was the main composition regardless of the DC magnetron sputtering power whereas the phase transition from n-type CuO to p-type Cu₂O was observed with decreasing the oxygen pressure (OP) from 40 to 20%. The optical band gap ranges of 1.6-1.9 eV, which are characteristic of n-type CuO, were determined for samples prepared with OPs of 30-40% while the optical band gap of 2.3 eV, which is characteristic of p-type Cu₂O, was measured for samples prepared with an OP of 20%. In addition, only Cu⁺ X-ray photoelectron spectroscopy (XPS) peak at the ~932.6 eV position exists in the films deposited with an OP of 20%, whereas only Cu²⁺ XPS peaks at ~934.2 eV and in the range of 940-945 eV are observed in the films deposited with an OP of 40%. Furthermore, as a result of XPS depth profile analysis, it was confirmed that the composition ratio of the sample prepared at an OP of 20% was Cu₂O, whereas the composition ratio of the sample prepared at an OP of 40% was CuO. These suggest that the CuO_x thin films could be constantly converted from n-type CuO to p-type Cu₂O by decreasing the oxygen partial pressure. Thin film transistors with Cu₂O deposited at 20% OP revealed p-type characteristics such as onset voltage (V_ON) of -3 V, saturated hole mobility of 8 cm²/Vs at V_GS = -28 V, subthreshold swing of 0.86 V/decade at V_GS-V_ON = -0.5 V, and on/off ratio of 1.14 × 10³.

• 조명전기설비학회논문지
• /
• 제28권9호
• /
• pp.1-7
• /
• 2014

Brushless Direct Current(BLDC) Motor is essential to measure a rotor position because of that this motor type needs to synchronize the rotor's position and changeover phase current instead of a brush and commutator used on the existing dc motor. Recently, many researches have studied on sensorless control drive for BLDC motor. The conventional control methods are a compensation value dq, Kalman filter, Fuzzy logic, Neurons neural network, and the like. These methods has difficulties of detecting BEMF accurately at low speed because of low BEMF voltage and switching noise. And also, the operation is long and complex. So, it is required a high-performance microprocessor. Therefore, it is not suitable for a small BLDC motor sensorless drive. This paper presents control methods suitable for economic small BLDC motor sensorless drive which are an improved design of the BEMF detection circuit, simplifying a complex algorithm and computation time reduction. The improved motor sensorless drive is verified stability and validity through being designed, manufactured and analyzed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.361-365
• /
• 2002

Advancements in silicon phase control (SCR) technologies provide an arc welding power supply that has the capability to allow the alteration of the Alternating Current (AC) welding output. These technologies provide a square wave output involving sixteen frequency selections and multiple balance selections. While an AC out put is known to minimize magnetic disturbances associate with Direct Current (DC), the potentials of a non-sinusoidal waveform have not been explored. The focus of the paper is to determine the effects that the frequency and balance of an AC wave form output will have upon a high speed Submerge Arc (SAW) application. The test matrix of the project includes welding .250" steel plate. Joint type is square groove with a travel speed of 65 IPM. Each of the weld parameters was held constant, only the frequency and/or balance were altered between welds. Each frequency/balance combination involved three-gap spacing. Upon completion of the welds the bead profiles were measured and recorded. A relationships/trends were observed with various frequency and balance values. Optimum frequency and balance values were found for the .250" square groove application which permit consistent weld sizing, ease of slag removal, and minimal plate distortion.

• Journal of Electrical Engineering and Technology
• /
• 제11권3호
• /
• pp.662-669
• /
• 2016

In this work, nonlinear control of a three-phase shunt active power filter (SAPF) has been studied and compared to classical control based on proportional integral regulator. The control strategy is based on the direct current method using sliding mode control (SMC), where the aim is to regulate the average voltage across the dc bus of the inverter. Details are given for the control algorithm; the controller is comprised of a current loop which utilizes a hysteresis controller to generate the gating signals for the switching devices, and a nonlinear controller based on SMC law which is different from classical laws based on error between reference and measured output voltage of the inverter. Sliding surface applied in this work contains the whole of state variables, in order to ensure full control of the system behavior in the presence of disturbances that affect the supply source, the load parameters or the reference value. The designed controller offers advantage that it can gives the improvement of dynamic and static performances in cases of large disturbances. A comparison of the effects of PI control and SMC on the APF response in steady stat, under line variations, load variations, and different component variations is performed.

• Journal of Plant Biology
• /
• 제29권1호
• /
• pp.1-10
• /
• 1986

Intra- and inter-specific protoplast fusion of tobacco (Nicotiana tabacum cv. Virginia 115) and pea (Pisum sativum cv. Sparkle) were carried out in highly inhomogeneous alternating electric fields. Under the electric field of alternating current (AC, sine wave), 600 V/cm and 800 kHz for tobacco protoplast, and 600 V/cm and 700 kHz for pea protoplasts, the protoplasts were aggregated in pearl chains. Intra-specific protoplast fusions were most effectively induced within the aggregates of tobacco and pea, respectively, by the additional application of a single high field pulse of direct current (DC, square wave) at 1 kV/cm for 50 $mutextrm{s}$. Inter-specific fusions between protoplasts of the two plants were most effectively induced in the electric field of 600 V/cm and 700 kHz, and square wave pulse at 1 kV/cm for 50 $mutextrm{s}$. The duration of the pulse over the electrical breakdown voltages was simulated from 1 to 100 $mutextrm{s}$ in both tobacco and pea protoplast. The yield of the electrofusion products was significantly high (above 60%), compared with that (20%) of the standard fusion method by polyethylene glycol (PEG) 4,000, and the viability of electrofused protoplasts was above 70%, but that of PEG-fused protoplasts 8~16%, when determined by Evan's blue staining method.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1501-1510
• /
• 2014

Low voltage direct current (LVDC) distribution system is a suitable techno-economic candidate which can create an innovative solution for distribution network development with respect to rural electrification. This research focuses on the use of LVDC distribution system to replace some of KEPCO's existing traditional medium voltage alternating current (MVAC) distribution network for rural electrification in South Korea. Considering the technical and economic risks and benefits involved in such project, a comparative techno-economic analysis on the LVDC and the MVAC distribution networks is conducted using economic assessment method such as the net present value (NPV) on a discounted cash flow (DCF) basis as well as the sensitivity analysis technique. Each would play a role in an economic performance indicator and a measure of uncertainty and risk involved in the project. In this work, a simulation model and a computational tool are concurrently developed and employed to aid the techno-economic analysis, evaluation, and estimation of the various systems efficiency and/or performance.

• 한국산업융합학회 논문집
• /
• 제24권4_1호
• /
• pp.377-385
• /
• 2021

High voltage direct current(HVDC) systems has been an alternative method of a power transmission to replace high voltage alternate current(HVAC), which is a traditional AC transmission method. Due to technical limitations, Line commutate converter HVDC(LCC-HVDC) was mainly used. However, result from many structural problems of LCC-HVDC, the voltage source converter HVDC(VSC-HVDC) are studied and applied recently. In this paper, after analyzing the reactive power and output voltage ripple, which are the main problems of LCC-HVDC, the characteristics of each HVDC are summarized. Based on this result, a new LCC-HVDC structure is proposed by combining LCC-HVDC with the MMC structure, which is a representative VSC-HVDC topology. The proposed structure generates lower reactive power than the conventional method, and greatly reduces the 12th harmonic, a major component of output voltage ripple. In addition, it can be easily applied to the already installed LCC-HVDC. When the proposed method is applied, the control of the reactive power compensator becomes unnecessary, and there is an advantage that the cut-off frequency of the output DC filter can be designed smaller. The validity of the proposed LCC-HVDC is verified through simulation and experiments.

• 한국진공학회지
• /
• 제10권3호
• /
• pp.356-360
• /
• 2001

다음극 DC PACVD법에서 합성된 직경 80 mm, 두께 900 $\mu\textrm{m}$ ~ 950 $\mu\textrm{m}$의 자유막 다이아몬드웨이퍼의 특성을 분석하였다. 광투과현미경으로 결함의 분포를 관찰하고, Raman 및 IR 장치로 결정성을 분석하였다. 결함은 결정입계 부위에서 많이 관찰되었다. 또한 하나의 결정립에서 (111)면이 (100)면에 비해 상대적으로 많은 결함을 함유하였다. Raman 다이아몬드 peak의 FWHM 및 10.6 $\mu\textrm{m}$ 파장에서의 IR 투과도는 각각 4.6 $\textrm{cm}^{-1}$ /~5.3 $\textrm{cm}^{-1}$및 51.7% ~ 61.9%로, 두 값의 웨이퍼 내에서 균일성은 $\pm$7% 및 $\pm$9%이었다. 다이아몬드 웨이퍼의 결정성은 가운데에서 가장자리로 갈수록 저하되었다.