• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.187-189
• /
• 2002

A relaying board is developed for the study of digital relay, which is based on Digital Signal Processor(DSP). The present development is capable of understanding and application for digital relay hardware. To support the design of relaying hardware, first A/D convertor MMI and serial port for communication are embedded, and next a booting cables of three types are supplied. More particularly the relaying board that is convinient to test digital relaying algorithm. This paper concludes by implementing the distance relaying algorithm into a relaying board, the hardware test results show practically high performance.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.3
• /
• pp.219-226
• /
• 1992

In this study, Kalman filtering theory is applied to the estimation of symmetrical components from fault voltage and current signal when it comes to faults with the power system. An algorithm for estimating fault location accurately and quickly by calculating the symmetrical components from the extracted fundamental voltage phasor and current phasor is presented. Also, to confirm the validity of digital distance relaying techniques using Kalman filtering, the experimental results obtained by using the digital simulation of power system is shown.

• KIEE International Transactions on Power Engineering
• /
• v.2A no.4
• /
• pp.153-159
• /
• 2002

Power transformer protective relay should block the tripping during magnetizing inrush and rapidly operate the tripping during internal faults. Recently, the frequency environment of power system has been made more complicated and the quantity of 2nd frequency component in inrush state has been decreased because of the improvement of core steel. And then, traditional approaches will likely be maloperate in the case of magnetizing inrush with low second harmonic component and internal faults with high second harmonic component. This paper proposes a new relaying algorithm to enhance the fault detection sensitivities of conventional techniques by using a fuzzy logic approach. The proposed fuzzy based relaying algorithm consists of flux-differential current derivative curve, harmonic restraint, and percentage differential characteristic curve. The proposed relaying was tested with relaying signals obtained from EMTP simulation package and showed a fast and accurate trip operation.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.8
• /
• pp.388-395
• /
• 2005

It has always been of great importance in the electrical power system to educate an algorithm on the digital relaying, but it is difficult to educate an algorithm of a digital distance relay on power system because of exclusiveness of the relaying algorithm on power system. Therefore, we need a digital distance relay simulator, which can simulate the algorithm of the digital relaying on transmission line. In this Paper, we extract fundamental components using digital signal processing from data which are a variety of the simulated faults by EMTP. Then this simulator represents instantaneous values, ms values and symmetrical components that are calculated by fundamental components of voltages and currents. The Simulator also represents the zones of a digital distance relay and the locus of an impedance using GUI. Consequently, the developed simulator is particularly useful for understanding of the fundamental concepts of a distance relaying algorithm from a power system engineer points of view.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.10
• /
• pp.1215-1221
• /
• 1999

A high speed digital distance relaying algorithm based on a Wavelet Transformation is proposed. To obtain stable phasor values very quickly, first, a lowpass filter which has low cutoff frequency is used. Secondly, db2(Daubechies 2) Wavelet which has the data window of 4 samples is used. A FIR filter which removes the DC-offset component in current relaying signals is applied. In accordance with a series of tests, the operation time of the relaying algorithm is less than 3/4 cycles after faults in a 80 [km], 154[kV], 60[Hz] over-head transmission line system.

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.1028-1031
• /
• 1997

This Paper Presents a new digital balance relaying technique in two Parallel transmission lines. To obtain relaying signals, selected model is simulated using EMTDC. Test results of the proposed method show efficacy.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.286-288
• /
• 1998

A digital distance relaying algorithm immune to the effect of the fault resistance in single-phase to ground fault is proposed. The power frequency components of relaying signals are extracted by the 1 cycle DFT. To compensate the magnitude and phase of the estimated impedance, which is calculated by the general method, this algorithm uses phase difference between the zero sequence impedance of networks on both sided of the system.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.7
• /
• pp.855-862
• /
• 1999

A high speed digital distance relaying algorithm based on a least square error method is proposed. To obtain stable phasor values very quickly, first, a lowpass filter which has very short transient period and no overshoot is presented. Secondly, the least square error method having the data window of 3 samples is used by applying a FIR filter which removes the DC-offset component in current relaying signals. Test results show that the proposed distance relaying algorithm detects most of internal faults within a half cycle after faults in a 154[kV] overhead transmission line system.

• Journal of Communications and Networks
• /
• v.11 no.2
• /
• pp.196-206
• /
• 2009

Over the last five years, relaying or multihop techniques have been intensively researched as means for potentially improving link performance of wireless networks. However, the data rates of relays are often limited because they cannot transmit and receive on the same frequency simultaneously. This limitation has come to the attention of researchers, and recently a number of relay techniques have been proposed specifically to improve the data efficiency of relaying protocols. This paper surveys transmission protocols that employ first single relays, then multiple relays and finally multiple antenna relays. A common feature of these techniques is that novel signal processing techniques are required in the relay network to support increased data rates. This paper presents results and discussion that highlight the advantages of these approaches.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.375-379
• /
• 1990

A microprocessor-based multi-function switchgear for the protection, measurement and control of the power system is presented. For the extraction of the RMS values of the fundamental components of current and voltage signals, a simple digital filter based on cross-correlation of the distorted signal with even and odd heptagonal waves is used. The frequency response of this filter is almost identical to that of the filter based on the discrete fourier transform, while its computational requirement is far less. For the time delay element relaying, a new log-table based relaying algorithm is suggested. The suggested use of the heptagonal wave cross-correlation digital filter algorithm and a new relaying algorithm reduce the computational needs so drastically that all functions of the switchgear can be implemented on the microprocessor system. Real time testing of the implemented daboratory prototype show good practical response under different operating conditions.