• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2366-2371
• /
• 2007

Spray combustion characteristics of a conducting fuel electrospray have been studied for clean combustion technology. The multiplexing system which can retain the characteristics of the cone-jet mode is inevitable for the electrospray application. Charged micro droplets can be obtained in almost uniform size during operating the electrospray in the cone-jet mode. This experiment device set up the multiplexed grooved nozzle system with the extractor. Using the grooved nozzle, the stable cone-jet mode can be achieved at the each groove in the grooved mode. This electrospray system was applied to the diffusion combustion. It is the first step to discover the diffusion combustion characteristics of the electrospray. In case of the single grooved nozzle electrospray, the diffusion flames are occurred at each jet of grooved mode and they are quite stable. The exhaust gas analysis was indicated that there is the critical point which can make very stable diffusion combustion.

• 대한기계학회논문집B
• /
• 제31권12호
• /
• pp.979-985
• /
• 2007

Spray combustion characteristics of the conducting fuel electrospray has been studied for clean combustion technology. The electrospraying multiplexed system which can maintain the characteristics of the cone-jet mode is able to obtain charged micro droplets with high flow rate. In addition, they have monodisperse distribution during operating the electrospray in the cone-jet mode. The multiplexed grooved nozzle system with the extractor was applied to this experimental device set up. The stable grooved mode can be generated by the grooved nozzle and this electrospray system was applied to the diffusion combustion. It is the first step to discover the diffusion combustion characteristics of the electrospray, In case of the single grooved nozzle electrospray the diffusion flames are occurred at each Jet of grooved mode and they are quite stable. The exhaust gas analysis was indicated that there is the critical point which can make very stable diffusion combustion

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.149-155
• /
• 2002

A promising new approach to achieve low pollutants emission and improvement of flame stabilities is tested experimentally using a hybrid cyclone jet combustor employing both premixed and diffusion combustion mode, Three kind of nozzles are used for LNG(Liquified Natural Gas) as a fuel. The combustor is operated by two method, One is ATI(Air Tangential Injection) mode, generated swirl flow by air as general swirl combustor, and the other is PTI(Premixed gas Tangential Injection) mode, The PTI mode consists of diffusion flame of axial direction and premixed cyclone flame of tangential direction in order to stabilized the diffusion flame. The results showed that the stable region of the PTI mode is more larger than the ATI mode. In addition, the reduction of NOx emission in PTI mode, as compared with that for the ATI mode is at least 50% in stable region. Also, even using the low calorific fuel as $CO_2$-blended gas, the cyclone jet combustor has high performance of flame stability.

• 대한기계학회논문집B
• /
• 제28권2호
• /
• pp.146-153
• /
• 2004

A Promising new approach to achieve low pollutant emissions and improvement of flame stability is tested experimentally using a cyclone jet hybrid combustor employing both premixed and diffusion combustion mode. Three kinds of nozzle are tested for mixing enhancement of fuel and air. The LNG (Liquified Natural Gas) is used as a fuel. The combustor is operated by two methods. One is DC (Diffusion Combustion) mode generated swirl flow by air as general swirl combustor, and the other is HC (Hybrid Combustion) mode. The HC mode consists of diffusion jet flame of axial direction and premixed cyclone flame of tangential direction in order to stabilized the diffusion jet flame. The results showed that the flame stability of HC mode is significantly enhanced than that of DC mode through the change of mixing characteristics by modifications of fuel nozzle. In addition, the reductions of CO and NOx emission in HC mode, as compared with that for the DC mode, is large than about 50% in stable region. Also, even using the low calorific fuel as $CO_2$-blended gas, it is identified that the cyclone jet hybrid combustor has the high performance of flame stability.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.73-76
• /
• 1997

A low loss x-cut LiNbO$_3$ optical waveguide was fabricated by Ti in-diffusion and the guided-mode properties and total insertion loss of pigtailing with polarization maintaining fiber(PMF) were investigated and measured at optical wavelength 15507. For formaing the waveguide, the parameters of diffusion Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set 1400$\AA$, 8${\mu}{\textrm}{m}$, 3.3cm, 105$0^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. and then After the polishing and pigtailing, it showed that total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, horizontal/vertical sizes were 13.87/18${\mu}{\textrm}{m}$ for TM mode, 9.61${\mu}{\textrm}{m}$/6.5${\mu}{\textrm}{m}$ for TE mode.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.682-691
• /
• 1997

We have investigated the guided optical properties of a Ti:LiNbO$_3$optical waveguide which was fabricated by Ti-diffusion in an air atmosphere and proposed an effective polishing method of waveguide endfaces. And the results of guided optical mode and fabrication condition were obtained as follows; \circled1 propagation loss : 0.53 dB/cm \circled2 mode size : horizontal/vertical=12.5${\mu}{\textrm}{m}$ \circled3 mode mismatch : 1.7 dB \circled4 diffusion temperature : 105$0^{\circ}C$, time : 8 hours \circled5 atmosphere : air

• 한국전기전자재료학회논문지
• /
• 제11권7호
• /
• pp.557-564
• /
• 1998

A low loss x-cut $LiNbO_3$optical waveguide was fabricated by Yi in-diffusion, and the properties of guided-mode and the total insertion loss of the pigtailed waveguide with polarization maintaining fiber(PMF) were measured at optical wavelength 1550nm. for forming the waveguides, the parameters of diffusion, Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set $1400{\AA}$, $8{\mu}m$, 3.3cm, $1050^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. And then after the polishing and piatailing, it showed that the total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, the horizontal/ vertical size were $13.8{\mu}m/18{\mu}m$ for TM mode, $9.6{\mu}m/6.5{\mu}m$ for TE mode.

• 한국전기전자재료학회논문지
• /
• 제11권5호
• /
• pp.400-406
• /
• 1998

We investigated the preparation and guided-mode properties of $Ti:LiNbO_3$ waveguides which were fabricated by Ti in-diffusion. The diffusion method to reduce the Li out-diffusion was proposed. The optical guided-mode and propagation loss based on butt-coupling pigtailed with PMF-input were measured. How to improve the polishing grade of waveguide endfaces is newly proposed in this paper. To show the mode propagations, the BPM simulations of channel waveguide are described.

• Nuclear Engineering and Technology
• /
• 제19권4호
• /
• pp.310-316
• /
• 1987

중성자 확산 방정식의λ -mode를 구하는 반복 계산법을 정립하였고, 이 방법을 이용한 2군, 3차원 전산 코드 MOGEN을 개발하였다. 2차원 직각형 균질 원자로에 대해 계산을 수행하여, 생산된 고유치와 고유함수가 해석해에 잘 일치함을 보여 코드의 정확도를 검증하였다. 실제 CANDU형 포준 원자로의 2차원 mode를 생산하였고, 이는 기존의 mode특성을 정확히 나타내었다. 마지막으로, λ-mode의 응용분야에 대하여 간략히 설명하였다.

• 교육녹색환경연구
• /
• 제4권4호
• /
• pp.1-18
• /
• 2004

Research has been carried out to study thermal environment in a classroom under three kinds of air diffusion temperature and six kinds of air diffusion direction for ceiling type air conditioner. The velocity and temperature distributions of air in the room calculated by 3-dimensional numerical method(PHOENICS), This present study was also conducted to calculate the Air Diffusion Performance Index(ADPI) for cooling conditions and Predicted Percentage of Dissatisfied(PPD) for heating conditions. This analysis shows that the optimum angle of ceiling type air conditioner's diffusion is $15{\sim}30^{\circ}$ for cooling mode and about $15{\sim}45^{\circ}$ for heating mode in these calculating conditions. And also analysis has been carried out to evaluate thermal comfort of vertical and horizontal cross section of classroom.