• 한국진공학회지
• /
• 제10권2호
• /
• pp.189-193
• /
• 2001

TiN을 불소의 확산 방지막으로 사용한 W-TiN 복층 게이트 소자의 물리적.전기적 특성 변화를 살펴보았다. TiN 스퍼터링 증착시 $N_2$/Ar 가스 비율이 증가할수록 TiN 박막은 N-과다막이 되어 비저항이 증가하였으나, W-TiN복층 구조에서는 $N_2$/Ar가스 비율이 증가할수록 상부 텅스텐 박막의 결정화가 증가하여 비저항이 감소하였다. 한편, 같은 $N_2$/Ar 비율의 경우, TiN 박막 열처리 온도 변화(600~$800^{\circ}C$)에 무관하게 W(110) 방향으로 우선 배향된 결정 구조를 보였다. 누설 전류 특성은 TiN증착시 $N_2$/Ar 비율 변화에 무관하게 우수하였으며, TiN을 확산 방지막으로 사용함으로서 순수 텅스텐 전극만을 적용시 나타나는 초기 저전계 누설 특성을 향상시킬 수 있음을 확인하였다.

• 한국재료학회지
• /
• 제13권1호
• /
• pp.43-47
• /
• 2003

As and BF$_2$dopants are implanted for the formation of source/drain with dose of 1${\times}$10$^{15}$ ions/$\textrm{cm}^2$∼5${\times}$10$^{15}$ ions/$\textrm{cm}^2$ then formed cobalt disilicide with Co/Ti deposition and doubly rapid thermal annealing. Appropriate ion implantation and cobalt salicide process are employed to meet the sub-0.13 $\mu\textrm{m}$ CMOS devices. We investigated the process results of sheet resistance, dopant redistribution, and surface-interface microstructure with a four-point probe, a secondary ion mass spectroscope(SIMS), a scanning probe microscope (SPM), and a cross sectional transmission electron microscope(TEM), respectively. Sheet resistance increased to 8%∼12% as dose increased in $CoSi_2$$n^{＋}$ and $CoSi_2$$p^{V}$ , while sheet resistance uniformity showed very little variation. SIMS depth profiling revealed that the diffusion of As and B was enhanced as dose increased in $CoSi_2$$n^{＋}$ and $CoSi_2$$p^{＋}$ . The surface roughness of root mean square(RMS) values measured by a SPM decreased as dose increased in $CoSi_2$$n^{＋}$ , while little variation was observed in $CoSi_2$$p^{＋}$ . Cross sectional TEM images showed that the spikes of 30 nm∼50 nm-depth were formed at the interfaces of $CoSi_2$$n^{＋}$ / and $CoSi_2$/$p^{＋}$, which indicate the possible leakage current source. Our result implied that Co/Ti cobalt salicide was compatible with high dose sub-0.13$\mu\textrm{m}$ process.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.131-131
• /
• 2003

Surface micromachined uncooled IR detector with the optimized VOx bolometric layer was fabricated based on sandwich structure of the V$_2$O$_{5}$V/V$_2$O$_{5}$. In order to improve the detectivity of the IR detector, we optimized a few factors in the viewpoint of bolometric material. Vanadium oxide thin film is a promising material for uncooled microbolometers due to its high temperature coefficient of resistance at room temperature. It is, however, very difficult to deposit vanadium oxide thin films having high temperature coefficient of resistance and low resistance because of process limits in microbolometer fabrication. In order to increase the responsivity and decrease noise, we increase TCR of bolometric material and decrease room temperature resistance based on the sandwich structure of the V$_2$O$_{5}$V/V$_2$O$_{5}$ by conventional sputter. By oxygen diffusion through low temperature annealing of V$_2$O$_{5}$V/V$_2$O$_{5}$ in oxygen ambient, various mixed phase vanadium oxide was formed and we obtained TCR in range of-1.2 ~-2.6%/$^{\circ}C$ at room temperature resistance of 5~100k$\Omega$.mega$.

• 한국분말재료학회지
• /
• 제23권5호
• /
• pp.384-390
• /
• 2016

Tri-isotropic (TRISO) coatings on zirconia surrogate beads are deposited using a fluidized-bed vapor deposition (FB-CVD) method. The silicon carbide layer is particularly important among the coated layers because it acts as a miniature pressure vessel and a diffusion barrier to gaseous and metallic fission products in the TRISO-coated particles. In this study, we obtain a nearly stoichiometric composition in the SiC layer coated at $1400^{\circ}C$, $1500^{\circ}C$, and $1400^{\circ}C$ with 20 vol.% methyltrichlorosilane (MTS), However, the composition of the SiC layer coated at $1300-1350^{\circ}C$ shows a difference from the stoichiometric ratio (1:1). The density decreases remarkably with decreasing SiC deposition temperature because of the nanosized pores. The high density of the SiC layer (${\geq}3.19g/cm^2$) easily obtained at $1500^{\circ}C$ and $1400^{\circ}C$ with 20 vol.% MTS did not change at an annealing temperature of $1900^{\circ}C$, simulating the reactor operating temperature. The evaluation of the mechanical properties is limited because of the inaccurate values of hardness and Young's modulus measured by the nano-indentation method.

• 한국분말재료학회지
• /
• 제16권1호
• /
• pp.9-15
• /
• 2009

Amorphization and crystallization behaviors of $Ti_{50}Cu_{50}Ni_{20}Al_{10}$ powders during high-energy ball milling and subsequent heat treatment were studied. Full amorphization obtained after milling for 30 h was confirmed by X-ray diffraction and transmission electron microscope. The morphology of powders prepared using different milling times was observed by field-emission scanning electron microscope. The powders developed a fine, layered, homogeneous structure with prolonged milling. The crystallization behavior showed that the glass transition, $T_g$, onset crystallization, $T_x$, and super cooled liquid range ${\Delta}T=T_x-T_g$ were 691,771 and 80 K, respectively. The isothermal transformation kinetics was analyzed by the John-Mehn-Avrami equation. The Avrami exponent was close to 2.5, which corresponds to the transformation process with a diffusion-controlled type at nearly constant nucleation rate. The activation energy of crystallization for the alloy in the isothermal annealing process calculated using an Arrhenius plot was 345 kJ/mol.

• Transactions on Electrical and Electronic Materials
• /
• 제4권3호
• /
• pp.34-37
• /
• 2003

[ $HfO_2$ ] and $HfO_xN_y$ films were deposited by plasma-enhanced chemical vapor deposition using $Hf[OC(CH_3)_3]_4$ as the precursor in the absence of $O_2$. The crystallization temperature of the $HfO_xN_y$ films is higher than that of the $HfO_2$ film. Nitrogen incorporation in $HfO_xN_y$ was confirmed by auger electron spectroscopy analysis. After post deposition annealing (PDA) at 800$\Box$, the EOT increased from 1.34 to 1.6 nm in the $HfO_2$ thin films, whereas the increase of EOT was suppressed to less than 0.02 nm in the $HfO_xN_y$. The leakage current density decreased from 0.18 to 0.012 $A/cm^2$ with increasing PDA temperature in the $HfO_2$ films. But the leakage current density of $HfO_xN_y$ does not vary with increasing PDA temperature because an amorphous $HfO_xN_y$ films suppresses the diffusion of oxygen through the gate dielectric.

• Transactions on Electrical and Electronic Materials
• /
• 제11권3호
• /
• pp.120-125
• /
• 2010

For the fabrication of PMOS and integrated semiconductor devices, B, $BF_2$ and dual elements with B and $BF_2$ can be implanted in silicon. 15 keV B ions were implanted in silicon at $7^{\circ}$ wafer tilt and a dose of $3.0{\times}10^{16}\;cm^{-2}$. 67 keV $BF_2$ ions were implanted in silicon at $7^{\circ}$ wafer tilt and a dose of $3.0{\times}10^{15}\;cm^{-2}$. For dual implantations, 67 keV $BF_2$ and 15keV B were carried out with two implantations with dose of $1.5{\times}10^{15}\;cm^{-2}$ instead of $3.0{\times}10^{15}\;cm^{-2}$, respectively. For the electrical activation, the implanted samples were annealed with rapid thermal annealing at $1,050^{\circ}C$ for 30 seconds. The implanted profiles were characterized by using secondary ion mass spectrometry in order to measure profiles. The implanted and annealed results show that concentration profiles for the ${BF_2}^+$ implant are shallower than those for a single $B^+$ and dual ($B^+$ and ${BF_2}^+$) implants in silicon. This effect was caused by the presence of fluorine which traps interstitial silicon and ${BF_2}^+$ implants have lower diffusion effect than a single and dual implantation cases. For the fabricated diodes, current-voltage (I-V) and capacitance-voltage (C-V) were also measured with HP curve tracer and C-V plotter. Electrical measurements showed that the dual implant had the best result in comparison with the other two cases for the turn on voltage characteristics.

• Transactions on Electrical and Electronic Materials
• /
• 제9권1호
• /
• pp.6-11
• /
• 2008

In this study, we investigated effects of hydrogen annealing (HA) and plasma nitridation (PN) applied in order to improve $Si/SiO_2$ interface characteristics of TiN metal gate. In result, HA and PN showed a positive effect decreasing number of interface state $(N_{it})$ respectively. After FN stress for verifying reliability, however, we identified rapid increase of $N_{it}$ for TiN gate with HA, which is attributed to hydrogen related to a change of $Si/SiO_2$ interface characteristic. In contrast to HA, PN showed an improved Nit and gate oxide leakage characteristic due to several possible effects, such as blocking of Chlorine (Cl) diffusion and prevention of thermal reaction between TiN and $SiO_2$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.207-207
• /
• 2012

Si quantum dot (QD) imbedded in a $SiO_2$ matrix is a promising material for the next generation optoelectronic devices, such as solar cells and light emission diodes (LEDs). However, low conductivity of the Si quantum dot layer is a great hindrance for the performance of the Si QD-based optoelectronic devices. The effective doping of the Si QDs by semiconducting elements is one of the most important factors for the improvement of conductivity. High dielectric constant of the matrix material $SiO_2$ is an additional source of the low conductivity. Active doping of B was observed in nanometer silicon layers confined in $SiO_2$ layers by secondary ion mass spectrometry (SIMS) depth profiling analysis and confirmed by Hall effect measurements. The uniformly distributed boron atoms in the B-doped silicon layers of $[SiO_2(8nm)/B-doped\;Si(10nm)]_5$ films turned out to be segregated into the $Si/SiO_2$ interfaces and the Si bulk, forming a distinct bimodal distribution by annealing at high temperature. B atoms in the Si layers were found to preferentially substitute inactive three-fold Si atoms in the grain boundaries and then substitute the four-fold Si atoms to achieve electrically active doping. As a result, active doping of B is initiated at high doping concentrations above $1.1{\times}10^{20}atoms/cm^3$ and high active doping of $3{\times}10^{20}atoms/cm^3$ could be achieved. The active doping in ultra-thin Si layers were implemented to silicon quantum dots (QDs) to realize a Si QD solar cell. A high energy conversion efficiency of 13.4% was realized from a p-type Si QD solar cell with B concentration of $4{\times}1^{20}atoms/cm^3$. We will present the diffusion behaviors of the various dopants in silicon nanostructures and the performance of the Si quantum dot solar cell with the optimized structures.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.153-153
• /
• 2011

유리나 폴리머를 기판으로 하는 TFT(Thin film transistor), solar cell에서는 낮은 공정 온도에서($200{\sim}500^{\circ}C$) amorphous semiconductor thin film을 poly-crystal semiconductor thin film으로 결정화 시키는 기술이 매우 중요하게 대두 되고 있다. Ge은 Si에 비해 높은 carrier mobility와 낮은 녹는점을 가지므로, 비 저항이 낮을 뿐만 아니라 더 낮은 온도에서 결정화 할 수 있다. 하지만 일반적으로 쓰이는 Ge의 결정화 방법은 비교적 높은 열처리 온도를 필요로 하거나, 결정화된 원소에 남아있는 metal이 불순물 역할을 한다는 문제점, 그리고 불균일한 결정크기를 만든다는 단점이 있었다. 그 중에서도 현재 가장 많이 쓰이고 있는 MIC, MILC는 metal과 a-Ge이 접촉되는 interface나, grain boundary diffusion에 의해 핵 생성이 일어나고, 결정이 성장하는 메커니즘을 가지고 있으므로 단순 증착과 열처리 만으로는 앞서 말한 단점을 극복하는데 한계를 가지고 있다. 이에 PIII&D 장비를 이용하면, 이온 주입된 원소들이 모재와 반응 할 수 있는 표면적이 커짐으로 핵 생성을 조절 할 수 있을 뿐만 아니라, 이온 주입 시 발생하는 self annealing effect로 결정 크기까지도 조절할 수 있다. 또한 이러한 모든 process가 한 진공 장비 내에서 이루어지므로 장비의 단순화와, 공정간 단계별로 발생하는 불순물과 표면산화를 막을 수 있으므로 절연체 위에 저항이 낮고, hall mobility가 높은 poly-crystalline Ge thin film을 만들 수 있다. 본 연구에서는, 주로 핵 생성과정에서 seed를 만드는 이온주입 조건과, 결정 성장이 일어나는 증착 조건에 따라서 Ge의 결정방향과 크기가 많은 차이를 보이는데, 이는 HR-XRD(High resolution X-ray Diffractometer)와 Raman spectroscopy를 이용하여 측정 하였으며, SEM과 AFM으로 결정의 크기와 표면 거칠기를 측정하였다. 또한 Hall effect measurement를 통해 poly-crystalline thin film 의 저항과 hall mobility를 측정하였다.