• 한국재료학회지
• /
• 제22권12호
• /
• pp.650-657
• /
• 2012

For the purpose of improving the durability problem, translucent opal glass was fabricated as a substitute for the polycarbonate diffuser of LED lighting. Calcium phosphate was used as an opacifier of opal glass and melted in an electric furnace. The opaque effect was identified according to the change of the cooling procedure. As results, translucent opal glass was obtained by the melting of a batch with a composition of 3.8% calcium phosphate at $1550^{\circ}C$ for 2 hrs and then the cooling of the material in the furnace. For the cooling condition of the glass sample, HTCG (High Temperature Cooled Glass) was found to have better optical properties than LTAG (Low Temperature Annealed Glass). It had excellent optical properties for a diffuser of LED lighting, with no dazzling from direct light due to its high haze value of over 99% and low parallel transmittance value of under 1%. For the thermal properties, it had an expressed thermal expansion coefficient of $5.7{\times}10^{-6}/^{\circ}C$ and a softening point of $876^{\circ}C$; it also had good thermal properties such as good thermal shock resistance and was easy to apply to the general manufacturing process in the forming of glass tubes and bulbs. Therefore, it is concluded that this translucent opal glass can be used as a glass diffuser material for LED lighting with high heat resistance and high durability; this material is suitable as a substitute for polycarbonate diffusers.

• 태양에너지
• /
• 제7권2호
• /
• pp.22-29
• /
• 1987

This paper dealed with thickness variation of bottom heat sotrage zone due to salinity and flow rate of extration hot brine in small test solar pond (0.5m wide, 0.5m high, 1.0m long). Testing apparatus and situation were follows: 7.1 cm of height of suction diffuser and 1.8cm of height of discharge diffuser above the test pond respectively, 0.3cm of slot size of suction diffuser, 1.0cm of slot size of discharge diffuser, 47cm of length of the slot; heating of hot water ($75^{\circ}C$) through separated hot water tank, discharge of the brine into storage zone through discharge diffuser, the extration of the brine through suction diffuser, circulation of the extracted brine through a heat exchanger (cooler). Following results were obtained through the experiments. 1. In small test solar pond, the typical three zone which showed up in real solar pond were established. 2. Richardson Number was used more effectively to confirm hydrodynamic stability of the stratified flow. 3. The thickness of non convective layer had a great effect on the heat storage of the bottom convective layer, then the temperature of bottom convective layer had a relation to that of upper convective layer. 4. Optimum operating condition in the test pond was on 10%-15% of salt concentration and $0.05m^3/hr$ of flow rate of extraction hot brine. 5. Following thickness of 3 zones were available to obtain under optimum operation condition: o bottom storage zone: $30%{\pm}10%$ of total pond depth o non-convective zone: $40%{\pm}10%$ of total pond depth o Upper surface zone: $20%{\pm}10%$ of total pond depth.

• 한국음향학회지
• /
• 제31권3호
• /
• pp.115-128
• /
• 2012

본 연구는 확산체의 확산계수 측정결과를 바탕으로 확산체의 설치가 홀 내부 음장분포에 미치는 영향에 대하여 알아보았다. 오케스트라쉘이 설치된 600석 규모의 축소모형 홀을 측정대상으로 이용하였다. 잔향실법 흡음률 측정을 통해 1: 25 축소모형의 벽체와 객석부 재료 (관객 및 의자)가 선정되었고, 만석 시 잔향시간을 기준으로 컴퓨터 시뮬레이션과 대응되도록 제작하였다. 다양한 확산체 부착위치에 따른 물리적 음장의 변화를 측정하기 위해 반구 확산체를 측벽, 발코니전면, 천장 등 부위별로 7가지 조합을 만들어, 확산체 유/무에 따른 음향지표의 변화를 측정하였다. 사용된 음향지표는 잔향시간 (RT), 초기감쇠시간 (EDT), 명료도 (C80), 중심시간 (Ts), 음압레벨 (G)과 더불어 임펄스리스펀스의 자기상관함수 (ACF)로부터 도출되는 Temporal diffusion (TD)을 이용하였다. 실험결과, 확산체 설치에 따라 흠음력과 확산면적이 증가하였고, 이에 따라 평균 RT, 평균 EDT, 평균 G는 감소하는 경향을 보였다. 또한 확산체 설치로 인해 초기반사음의 방향전환이 활발하게 발생했고, 평균 TD은 측정 케이스에 따라 6.05에서 6.30의 값을 보였다. 확산체 설치에 가장 민감한 지표는 RT (R = 0.94)로 나타났고, TD와 EDT의 상관관계 (R = 0.73)가 높은 것으로 나타났다. 확산체 설치부위의 영향은 각 음향지표의 변화양상을 통해 논의되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.958-964
• /
• 2001

It is difficult to apply a conventional selection guide for diffusers when the diffuser is installed in a perimeter zone, because the ADPI(Air Diffusion Performance Index) vs. T/L(Throw/Length) curve listed in conventional guide does not consider the perimetric heating load. The objective of this study is to evaluate the effect of the perimetric heating load on the ADPI and to propose a selection guide for proper diffuser when perimetric heating load exists. The velocity and temperature distributions and the ADPI value are obtained numerically with various heat load ratios and air flow rates. The ADPI values by numerical result were compared with existing experimental data to verify the method for evaluation of ADPI proposed in present study. In case of a high side wall diffuser, the ADPI decreased with increases of the flow rate on every heat load ratio of present study except 0.75. Also, the ADPI vs. T/L curves have been proposed for the heat load ratios of 0.25, 0.5, 0.75 to guarantee comport thermal environment when diffusers are installed in perimeter zone.

• 한국추진공학회지
• /
• 제5권4호
• /
• pp.50-56
• /
• 2001

본 연구는 음속/초음속 공기이젝터 시스템을 통하는 유동을 실험적으로 조사한 것으로, 이젝터 시스템의 2차정체실 압력-시간의 의존성을 조사하였다. 본 실험에서 적용된 1차구동 노즐은 총 6가지 형태로, 두 개의 음속노즐과 두 개의 초음속 노즐 그리고 페탈노즐 및 로브형 노즐이 사용되었다. 실험에서는 이젝터-디퓨저 벽면에서 압력을 측정하였으며, 2차 정실실의 체적이 이젝터 내부에 미치는 영향을 조사하기 위하여, 2차 정체실의 체적을 변화시켰다. 그 결과 2차정체실의 체적은 이젝터 시스템의 정상 작동에는 영향을 미치지 않았지만, 2차정체실에서의 압력-시간 의존성은 2차정체실의 체적에 큰 영향을 받는다는 것을 알았다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.131-135
• /
• 2010

In the present study, the effects of the stagger angles on the aerodynamic performances in the vaned centrifugal compressor has been investigated by CFD methods. The diffuser vane angles were vane angles were varied in the range of ${\pm}10$ deg. from the intial-design points. The commercial Navier-Stokes solver, ANSYS-CFX were applied to solve the impeller-diffuser flowfields. Through the numerical results, the desirable setting angles were proposed to fit the best performance to the variation of the operating conditions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1376-1378
• /
• 2006

Numerical and experimental study were carried out to characterize sound fields of low frequency in a scaled reverberation chamber for measurement of sound insulation of panels. By using BEM, lower modes of the chamber are identified and then predicted the effect of diffusers in order to destruct lower modes. Compared results with measurements show reasonable agreements, especially at the first end second modes. Based on numerical prediction, the diffuser are installed in order to improve sound fields to be more diffuse than ever. It is found that the diffuser put in nodal line of the chamber destruct evidently the first mode. Consequently, the measuring error at the low frequency can be relatively reduced compare to the case of without diffuser.

• 대한환경공학회지
• /
• 제34권11호
• /
• pp.772-779
• /
• 2012

본 연구에서는 원뿔형으로 개발된 미세기포형 산기관의 성능향상을 위하여 운용적 측면에서 실험과 전산모사적 방법을 이용하였다. 산기관 잠김깊이의 변화에 대해 성능실험이 용이한 실증 규모의 타워형 생물반응기에 산기관을 장착하여, 잠김깊이가 표준산소전달계수($K_{L}a_{20}$) 및 표준산소전달효율(SOTE) 등 산소전달 성능에 미치는 영향을 실험적으로 연구하였다. 또한, 2상 유동에 관한 유체역학적 전산모사를 이용하여 산기관 수와 잠김깊이에 대한 유동현상을 파악함으로써 산소전달 성능변화에 대한 원인을 규명하였다. 산소전달 성능실험결과, 산기관의 잠김깊이를 6 m에서 12 m로 증가시킴에 따라 표준산소 전달계수는 7% 증가하였으나 표준산소전달효율은 39~72% (5.6 %/m)로 대폭 상승하였다. 유동 해석결과, 산기관의 수가 증가함에 따라 공기 체적분율 및 공기와 시험수의 유속 모두 증가하였으며, 공기와 시험수의 유속 경향은 유사하게 나타났다. 잠김깊이가 증가함에 따라서 공기 체적분율, 공기 및 시험수의 유속은 조금씩 감소하는 경향을 나타냈다. 선회 병류유동은 기포류의 확산과 상승속도를 결정하는 주요 인자로서 선회강도가 과도하게 큰 경우에는 기포 체류시간과 체류량이 감소되므로 산소전달 성능을 저하를 예측할 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.422-427
• /
• 2000

The design of low-solidity vaned diffusers and the effect on the performance of a turbocharger compressor is discussed. The effect of vane number and turning angle was investigated while maintaining a basic design with a leading edge angle of $70^{\circ}$, leading and trailing edge radius ratios of 1.1 and 1.3. All results are compared with those obtained with the standard vaneless diffuser configuration and it was shown that all designs increased and shifted the pressure ratio to reduced flowrates. Despite the low-solidity configuration none of the vane designs provided a broad operating range, and the vane leading edge angle was not main factor that system went into the surge condition. The diffuser of higher trailing edge angle improved the flow range for the compressor to operate at lower flow region.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.15-20
• /
• 2006

Despite the fact that UFAD (Under Floor Air Distribution) systems have many benefits and are being applied in the field in increasing numbers, there is a strong need for an improved fundamental understanding of several key performance features of these systems. This study numerically investigates the effect of design parameters on the performance of UFAD, especially focused on thermal comfort. The design parameters considered in this study include supplied air temperature, supplied flow rate, diffuser shape, swirl, diffuser location, and floor-to-floor height. Also this study has compared UFAD with over head system, on the point of thermal comfort by evaluating PMV using radiative mean temperature, which shows how inadequate the evaluation of thermal comfort can be when radiation is neglected. Until now, the radiative temperature has been the missing link between CFD and thermal comfort, but the present study paves the way for overcoming this weakness.