• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.7
• /
• pp.366-372
• /
• 2017

The objective of this study was to characterize Waveguide-Blow-Cutoff (WBC) array for Electromagnetic Pulse (EMP) shield in air duct or water pipe, the typical pathway of pulse in indoor space with critical electronic device. A numerical investigation with three different WBC designs (circular, rectangular, and hexagonal or honeycomb) was conducted to satisfy recommended shielding effectiveness (SE) levels from 80 dB to 140 dB. Pressure drop between upstream and downstream of EMP shields based on WBC arrays was also investigated to understand air flow feature in air duct of HVAC system. Results showed that honeycomb geometry outperformed other shapes in terms of reducing the depth of EMP shield, thus providing better air flow in duct path with lower local loss coefficient in HVAC system under SE requirements.

• Applied Science and Convergence Technology
• /
• v.23 no.5
• /
• pp.254-260
• /
• 2014

Organic solar cells have attracted extensive attention as a promising approach for cost-effective photovoltaic devices. However, organic solar cell has disadvantage of low power conversion efficiency in comparison with other type of solar cell, due to the recombination ratio of hole and electron is too large in the active layer. Thus we have change the surface structure of PEDOT:PSS layers to improve the current density by colloidal lithography method using various-size of polystyrene sphere. The two types of coating method were applied to fabricate the different pattern shape and height, such as spin coating and drop casting. Using the organic solvent, we easily eliminate the PS sphere and could make the varied pattern shapes by controlling the wet etching time. Also we have measured the electrical properties of patterned PEDOT:PSS film to check whether it is suitable for organic photovoltaics.

• Journal of Communications and Networks
• /
• v.6 no.2
• /
• pp.182-191
• /
• 2004

In this paper, performances of different ultra-wideband (UWB) modulation schemes in the presence of timing jitter are evaluated and compared. Static and Rayleigh fading channels are considered. For fading channels, Oat and dispersive channels are assumed. First, bit error rate (BER) performances for each case are derived for a fixed value of timing jitter. Later, a uniform distribution of jitter is assumed to evaluate the performance of the system, and the theoretical results are verified by computer simulations. Finger estimation error is treated as timing jitter and an appropriate model is generated. Furthermore, a worst case distribution that provides an upper bound on the system performance is presented and compared with other distributions. Effects of timing jitter on systems employing different pulse shapes are analyzed to show the dependency of UWB performance on pulse shape. Although our analysis assumes uniform timing jitter, our framework can be used to evaluate the BER performance for any given probability distribution function of the jitter.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.3
• /
• pp.100-106
• /
• 1997

Despite various devices have been developed and applied to stabilize the yaw motion, the superiority of twin skeg over other equi-functioned appendages has been recognized so far. In many cases, these skegs were installed with insufficient study and analysis for design, and this leads to the worse performance of their resistance and course keeping than required. Experimental studies on the effect of various kinds of anti-yawing skegs to the course keeping stability and on the additional resistance caused by them were carried out in the circulating water channel(CWC) at Chosun University(CU). Course keeping stability tests for four different size of skegs, resistance tests for three different shapes of skeg(including deformed skegs) were performed systematically. And the effect of angle of skegs on resistance was studied at the final stage.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1218-1224
• /
• 2016

This paper presents the results of a study on the effect of surface modified alumina nanocomposites on electrical tree growth in epoxy insulation. Treeing experiments were conducted at a fixde AC voltage (500kV/mm, 10kV/60Hz)on unfilled epoxy sample as well as epoxy nanocomposites of 4 types with different loading and surface modified GDE gram. Time for tree growth as well as tree propagation length were studied. The results show that there is a significant improvement tree propagation time compare unfilled epoxy to epoxy nano alumina composites. Different tree propagation shapes as well as slower tree growth with 4 types nano alumina composites were observed.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.188-195
• /
• 2004

Severe osteoarthrosis of the knee joint often requires total knee arthroplasty(TKA) to yield adequate knee function. The knee joint with TKA is expected ideally to restore the characteristics, however, this is not necessarily 1.ue in the clinical cases. In this study the motion of the intact joint and the joint after. TKA were investigated numerically using computer simulation. For active knee extension from 90 degrees of flexion to full extension, the intact knee joint exhibited anterior tibial translation near the full extension and it showed only rotation at other flexion angles. Physiologic external rotation of the tibia near full extension known as screw home movement was also noted in the analytical model. The analysis of the tibial insert of three different shapes (flat, semicurved, and curved types) demonstrated characteristic rotational and sliding motion as well as different contact forces.

• Wind and Structures
• /
• v.10 no.2
• /
• pp.135-151
• /
• 2007

This paper examines the extreme gust profiles obtained by conditionally sampling full-scale velocity data obtained in the lower part of the atmospheric boundary layer. It is demonstrated that three different types of behaviour can be observed in the streamwise component of velocity. In all cases the corresponding vertical velocity component illustrates similar behaviour. An idealised horseshoe vortex model and a downburst model are investigated to examine if such structures can explain the behaviour observed. In addition, an empirical model is developed for an isolated gust corresponding to each of the three types of behaviour observed. It is possible that the division of the gust profile into three different types may lead to an improvement in the correlation of extreme gust events with respect to type.

• Journal of Aerospace System Engineering
• /
• v.3 no.4
• /
• pp.1-6
• /
• 2009

Aerodynamic noise is becoming the major source of annoyance for modern cars recently and is caused by many different noise sources in a car. Appropriate CFD technologies, therefore, have been developed to resolve the noise problems related with aerodynamics. It is necessary for designers to fully understand the relationship between vehicle aerodynamics and wind noise acoustics. In this study, we simulate the flow fields around two different shapes of side mirror models of passenger car and analyze the noise phenomena around one side mirror model that has lower drag than the other model using Fluent 6.3.

• Korean journal of applied entomology
• /
• v.57 no.4
• /
• pp.279-285
• /
• 2018

Different English terms indicating a same part in insect head were arranged according to position and function, and their corresponding different Korean terms were suggested. The terms include lines on head surface, head regions of embryo, external and internal skeletons, internal parts of mouth, long mouths, external parts and basic segments of antenna, antennal shapes, and hairs on surface.

• Wind and Structures
• /
• v.28 no.6
• /
• pp.369-380
• /
• 2019

Statistical distributions are very useful in describing wind speed characteristics and in predicting wind power potential of a specified region. Although the Weibull distribution is the most popular one in wind energy literature, it does not seem to be able to perfectly fit all the investigated wind speed data in nature. Thus, many studies are still being conducted to find flexible distribution for modelling wind speed data. In this study, we propose a new Odd-Burr Rayleigh distribution for wind speed characterization. The Odd-Burr Rayleigh distribution with two shape parameters is flexible enough to model different shapes of wind speed data and thus it can be an alternative wind speed distribution for the assessment of wind energy potential. Therefore, suitability of the Odd-Burr Rayleigh distribution is investigated on real wind speed data taken from different regions in the South Africa. Numerical results of the conducted analysis confirm that the new Odd-Burr Rayleigh distribution is suitable for modelling most of the considered real wind speed cases and it also can be used for predicting wind power.