• Journal of Power System Engineering
• /
• v.20 no.1
• /
• pp.18-23
• /
• 2016

As diesel engines have high power and good fuel economy on top of less $CO_2$ emissions, their market shares are increasing not only in commercial vehicles but also in passenger cars. LNT, urea-SCR and combination of them have been developed for after-treatment of the exhaust gas to reduce NOx on diesel vehicles. The aim of this study is to investigate the $NH_3$ generation characteristics of LNT catalyst downstream. It was found from the experiments of the LNT catalyst that $H_2$ was useful as a reductant in SCR catalyst because it can enhance the de-NOx performance and improve $NH_3$ selectivity. The $NH_3$ generation of the LNT, when hydrothermally aged at $900^{\circ}C$ for 18 hr, increased to about 90ppm at $300^{\circ}C$ due to Pt sintering and Ba agglomeration. LNT catalyst was most sulfur poisoning at $500^{\circ}C$. The $NH_3$ slip increased due to the reduction of residence time according to SV increase.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.68-78
• /
• 2006

In the past few years, considerable efforts have been directed towards the further development of Urea-SCR(selective catalytic reduction) technique for diesel-driven vehicle. Although urea possesses considerable advantages over Ammonia$(NH_3)$ in terms of toxicity and handling, its necessary decomposition into Ammonia and carbon dioxide complicates the DeNOx process. Moreover, a mobile SCR system has only a short distance between engine exhaust and the catalyst entrance. Hence, this leads to not enough residence times of urea, and therefore evaporation and thermolysis cannot be completed at the catalyst entrance. This may cause high secondary emissions of Ammonia and isocyanic acid from the reducing agent and also leads to the fact that a considerable section of the catalyst may be misused for the purely thermal steps of water evaporation and thermolysis of urea. Hence the key factor to implementation of SCR technology on automobile is fast thermolysis, good mixing of Ammonia and gas, and reducing Ammonia slip. In this context, this study performs three-dimensional numerical simulation of urea injection of heavy-duty diesel engine under various injection pressure, injector locations and number of injector hole. This study employs Eulerian-Lagrangian approach to consider break-up, evaporation and heat and mass-transfer between droplet and exhaust gas with considering thermolysis and the turbulence dispersion effect of droplet. The SCR-monolith brick has been treated as porous medium. The effect of location and number of hole of urea injector on the uniformity of Ammonia concentration distribution and the amount of water at the entrance of SCR-monolith has been examined in detail under various injection pressures. The present results show useful guidelines for the optimum design of urea injector for reducing Ammonia slip and improving DeNOx performance.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.695-699
• /
• 2021

In this study, Selective Catalytic Reduction on Diesel Particulate Filter (SDPF) after-treatment system was introduced to simultaneously remove NO_x and Particulate Matters (PM) emitted from trucks and special cargo vehicles using old engine. First, in order to select an Selective Catalytic Reduction (SCR) catalyst for SDPF, the de-NO_x performance of V/TiO₂ and Cu-Zeolite catalysts were compared, and the SCR catalyst characteristics were analyzed through Brunauer Emmett Teller (BET), X-ray Diffraction (XRD) and NH3-TPD (Temperature Programmed Desorption). From the activity test results, the Cu-zeolite catalyst showed the best thermal stability. For optimal coating of SDPF, slurry was prepared according to the target particle size. From the coating stability and back pressure test results of SDPF according to the amount of SCR coating, As a result of comparing coating stability, back pressure, and de-NOx performance by producing A, B, and C samples for each loading amount of the SDPF catalyst, the best results were found in the B sample. The engine dynamometer test was conducted for the optimal SDPF after-treatment system, and the test results satisfied Eu-5 regulations.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.128-136
• /
• 2007

It is well known that two representative methods satisfy EURO-IV regulation from EURO-III. The first method is to achieve the regulation through the reduction of NOx in an engine by utilizing relatively high EGR rate and the elimination of subsequently increased PM by DPF. However, it results in the deterioration of fuel economy due to relatively high EGR rate. The second is to use the high combustion strategy to reduce PM emission by high oxidation rate and trap the high NOx emissions with DeNOx catalysts such as Urea-SCR. While it has good fuel economy relative to the first method mentioned above, its infrastructure is demanded. In this paper, the number distribution of nano PM has been evaluated by Electrical Low Pressure Impactor(ELPI) and CPC in case of Urea-SCR system in second method. From the results, the particle number was increased slightly in proportion to the amount of urea injection on Fine Particle Region, whether AOC is used or not. Especially, in case of different urea injection pressure, the trends of increasing was distinguished from low and high injection pressure. As low injection pressure, the particle number was increased largely in accordance with the amount of injected urea solution on Fine Particle Region. But Nano Particle Region was not. The other side, in case of high pressure, increasing rate of particle number was larger than low pressure injection on Nano Particle Region. From the results, the reason of particle number increase due to urea injection is supposed that new products are composited from HCNO, sulfate, NH3 on urea decomposition process.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.187-191
• /
• 2001

In the paper, an approach to the development of the selective catalytic reduction process of NOx is presented. The reduction process can be efficiently controlled using a conventional combination of feed-forward and feed-back control structures. The aim of this paper is to test and verify an approach to the SCR process which is based on an industrial pilot plant of combustion and nitric oxide formation. The systems are based on measurements of a NOx removal ratio and the fuel flow rate, and NH$_3$slip which are usually available as a part of de-NOx control system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.7
• /
• pp.429-434
• /
• 2016

Among various De-NOx technologies, Urea-based Selective Catalytic Reduction (SCR) systems are known to be the most effective in marine diesel applications. The spraying and mixing behavior of the urea-water solution has a decisive effect on the system's net efficiency. Therefore, in this study, the spray behavior and ammonia uniformity with and without a static mixer were analyzed by CFD in order to optimize the SCR system. The results showed that the static mixer significantly affected the uniformity of velocity and ammonia concentration. Static mixers may be especially suited for marine SCR systems with space constraints.