• 산업기술연구
• /
• 제22권A호
• /
• pp.193-200
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface IS a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this dissertation was to study the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), water-cement ratios and curing days at a same controlled environment of 60% of relative humidity and $20^{\circ}C$ of temperature The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower with low water-cement ratio, respectively This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.104-111
• /
• 2009

A ship engine operator should compensate the crankshaft assembly of ship engine after inspecting crankshaft deflection error in the crank throw regularly to avoid engine vibration and abrasions. In the previous method, the operator enters the bed plate and measures crankshaft deflection using dial gauge on rotating crankshaft manually. However, this method can cause dangerous situation to the operator as well as uncomfortable in an inferior environment. In order to solve the problems, this paper studies the method which makes the operator measure the error outside of the bed plate. In this paper, it is suggested that BlueTooth wireless communication transfers the error data to the outer standing operator with digitalized crankshaft deflection inspection device developed in this paper. So, the wireless measurement system is developed and applied to a medium-speed marine engine through size-miniaturization. After applying test, the developed inspection device showed that it provides much safe and ease inspection method. Furthermore, in the result, the measuring accuracy is more improved.

• 대한치과기공학회지
• /
• 제30권2호
• /
• pp.17-22
• /
• 2008

The purpose of this study was to observe the thermal expansion of the inlay waxes at temperature. Inlay pattern wax shows not only a high coefficient of expansion but also a tendency to warp or distort when allowed to stand unrestrained. The thermal expansion of inlay waxes was tested according to the treatment conditions for 10 minutes at $40^{\circ}C$ The thermal expansion of inlay waxes at various temperatures was measured with an electro dial gauge. The results were as fellows: 1. It is shown that the rate of thermal expansion of wax A is 0.2%, wax B is 0.29%, wax C is 0.38%, and wax D is 0.22% at $40^{\circ}C$ 2. It is shown that the coefficient of thermal expansion of wax A is $106{\times}10^{-6}/^{\circ}C$, wax B is $152{\times}10^{-6}/^{\circ}C$, wax C is $199{\times}10^{-6}/^{\circ}C$, and wax D is $116{\times}10^{-6}/^{\circ}C$ at $40^{\circ}C$ 3. The thermal expansion of the inlay waxes at $40^{\circ}C$ was shown to increase in the order of wax C, B, D, A.

• 대한치과기공학회지
• /
• 제28권2호
• /
• pp.367-373
• /
• 2006

This study was performed to observe the flow change of the inlay waxes at various temperatures. The flow of inlay waxes was tested according to the treatment conditions, for 10 minutes at 40$^{\circ}C$, 41$^{\circ}C$, 42$^{\circ}C$, 43$^{\circ}C$, 44$^{\circ}C$, and 45$^{\circ}C$ The flow of inlay waxes at various temperatures was measured with an electro dial gauge. The results were as fellows: 1. The flow change of the inlay waxes at various temperatures was shown to increase in the order of wax A, B, D, C. 2. Wax A was close to ADA specification with 3% flow at 40$^{\circ}C$ and 71% flow at 45$^{\circ}C$, but wax B and D did not reach up to ADA specification with 40% flow at 45$^{\circ}C$. 3. Wax C came up with 3% flow at 40$^{\circ}C$ and 7% flow at 45$^{\circ}C$, and it revealed a very low flow change at 5$^{\circ}C$.

• 한국물환경학회지
• /
• 제20권3호
• /
• pp.206-214
• /
• 2004

Residual wall thicknesses, corrosion rates, and residual life of thirty four samples of cast iron pipes(CIPs) and ductile cast iron pipes(DCIPs) collected from water mains of B city were studied to estimate their remaining service life or optimum time of rehabilitation. The internal maximum corrosion depths of samples measured using a dial gauge after shot blasting were twice higher than the external in most cases. Therefore corrosion of water pipes was much more affected by internal water quality than soil. Residual wall thicknesses of DCIPs were higher than those of CIPs. That reason was thought to be that DCIPs have been protected from internal corrosion by lining cement mortar. Residual life calculated by maximum corrosion rate was ranged up to 44 years with 12.40 years average. Since most CIPs were much deteriorated, rehabilitation plan should be established soon in B city. Residual life of DCIP was 33.52 years average. When cement mortar lining is used up by neutralization of DCIPs. DCIP also should be rehabilitated.

• 대한치과기공학회지
• /
• 제8권1호
• /
• pp.85-90
• /
• 1986

The effect of splinting on aqbutment tooth distal movement was performed in vitro study. An acrylic resin mandibular model with missing 2nd premolars, molars and a removable partial denture framework were constructed. The roots of the canines, 1st premolars and edentulous ridges were coated with silicone rubber. A modified Ney Surveyor was used for vertical load appkication, and abutment tooth distal movement were measured with a dial gauge with four conditions of splinting methods were tested by applying unilateral vertical loadings. The results are follows; 1. The magnitude of abutment tooth distal movement on the non-load side was less 40$\sim$69% than that occurred on the load side. 2. On the load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(30%), non-load side double abutment(10%), double abutments of both sides(40%) was compared with single abutments of both sides. 3. On the non-load side, reducing effect of splinting on abutment tooth movement in the condition of load side double abutment(5%), non-load side double abutment(22%), double abutments of both sides(59%) was compared with single abutments of both sides. 4. The magnitude of abutment tooth distal movement in the condition of double abutments of both sides was less 40$\sim$59% than that in the condition of single abutments of both sides.

• 대한전자공학회논문지
• /
• 제27권10호
• /
• pp.106-112
• /
• 1990

다공질 실리콘을 열산화할 때 산화의 온도 의존성과 IR흡수 스펙트럼을 조사하여 다공질 실리콘외 산화특성을 조사하였다. PSL(porous silicon layer)을 $700^{\circ}C$에서 1시간, $1100^{\circ}C$에서 1시간으로 2단계 습식산화시켜 bulk 실리콘의 열산화막과 같은 성질의 수십 ${\mu}m$두께의 OPSL(oxidized porous silicon layer)을 짧은 시간에 형성시킬 수 있으며, 식각율과 항복전계는 산화온도와 산화 분위기에 크게 의존하는 것으로 나타났다. 이때 PSL의 산화율은 약 390nm/s이고, 항복전계는 1.0MV/cm~2.0MV/cm의 분포를 갖는다. 웨이퍼 휨을 측정하여 고온 열산화시 발생하는 산화막의 stress를 조사하였다. $1000^{\circ}C$ 이상의 고온에서 건식산화할 경우 발생하는 stress는 ${10^2}dyne/{cm^2}~{10^10}dyne/{cm^2}$로 측정되었다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제36권1호
• /
• pp.23-27
• /
• 2010

The purpose of this study was to evaluate the reliability of 6-axis model surgery simulator (6AMSS) for orthognathic surgery. A rectangular parallelepiped plastic block was assembled to model-mounting plate of 6AMSS. Left-right (X), anterior-posterior (Y), up-down (Z) translation and pitching (${\phi}X$), rolling (${\phi}Y$) and yawing (${\phi}Z$) rotation was planned and performed using 6AMSS. The actual translation and rotation were measured with dial gauge and precisional protractor, respectively. Comparison between the planned and actual movements of plastic block for each variable were made using paired t- test. Statistical analysis for X, Y, Z, ${\phi}X$, ${\phi}Y$ and ${\phi}Z$ movement have shown no significant differences between planned and actual movement (P > 0.05). This indicate that model surgery performed with the aid of the 6AMSS is accurate in 3D translation and rotation. The 6AMSS is practically useful for accurate fabrication of surgical splint for orthognathic surgery.

• Composites Research
• /
• 제22권5호
• /
• pp.1-7
• /
• 2009

WR580/NF4000 유리섬유 에폭시 면재를 갖는 알루미늄 하니컴 샌드위치 복합재가 적용된 자동무인경전철 차체 구조물은 구조 시험과 유한요소 해석에 의해 평가되었다. 구조 시험은 JIS E 7105 규정에 따라 수행되었다. 차체 구조물의 추조 안전성은 다이얼 게이지와 가속도 센서를 통해 얻어진 처짐 및 고유진동수 결과에 의해 평가되었다. 그리고 제안된 유한요소 모델은 구조 시험 결과와 비교 되었으며, 유한요소 해석은 구조 시험과 잘 일치함을 보였다. 또한, 차제 구조물의 강성을 높이기 위해 언더프레임에 보강재가 적용된 모델은 설계단계에서 제안되었다. 보강된 언더프레임 모델을 갖는 복합재 차체 구조물은 구조 강성이 약 44%가 향상되었다.

• 대한방사선치료학회지
• /
• 제15권1호
• /
• pp.1-9
• /
• 2003

I. 목적 MLC의 단점인 조사영역경계의 요동현상이나, 반음영의 크기를 감소시킬 수 있는 HD270 MLC에 관한 소개와 유용성에 대해 평가하였다. II 대상 및 방법 HD-270 MLC는 PRIMUS(Siemens)의 치료테이블(ZXT) 과 다엽콜리메이터(3D MLC)를 leafs면에 수직방향으로 이동시킴으로써 유효반음영과 조사영역 경계의 요동을 감소시킨다. HD-270 MLC의 효율성과 적당한 resolution을 결정하기 위해 field edge angle(Y축과 이루는 각)이 0도에서 75도까지 15도의 간격으로 된 다각형의 field를 만들고 resolution은 5mm, 3mm, 2mm로 각각의 HD-270 group을 만들어 Siemens사 선형가속기(PRIMUS)의 6MV 광자선을 사용하여 solid phantom에서 SAD 100cm, depth 1.5cm으로 X-Omat film(Kodak)에 60MU로 조사하였다. 조사된 film은 Lumiscan75(LUMISYS)로 스캔해서 RIT113(Radiological Imaging Technology Inc. USA)으로 분석하여 유효반음영과 조사영역 경계의 요동의 변화를 측정하였다. 그리고 치료테이블 움직임의 정확성을 테스트하기 위해 테이블 위에 50Kg의 인체모형팬텀을 놓고 0.001inch의 정밀도를 가진 dial gauge로 가로, 세로, 수직의 세 직각방향으로 ${\pm}5mm,\;{\pm}4mm,\;{\pm}3mm,\;{\pm}2mm$단계별로 측정하였다 III. 결과 Resolution과 field edge angle이 증가할수록 유효반음영과 조사영역 경계의 요동현상은 증가하였다. 그리고 지멘스 ZXT 치료테이블움직임의 오차범위는 ${\pm}1mm$ 이내로 양호하였다. IV. 결론 최근 많이 사용되어지고 있는 다엽콜리메이터의 문제점들을 보완 할 수 있는 HD-270 MLC를 사용함으로써 MLC의 임상적용범위를 보다 넓힐 수 있을 것이다.