• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.367-368
• /
• 2014

This paper investigates characteristics of high power semiconductor device losses in 5MW-class Permanent Magnet Synchronous Generator (PMSG) Medium Voltage (MV) wind turbines. High power semiconductor device of press-pack type IGCT of 6.5kV is considered in this paper. Analysis is performed based on neutral point clamped (NPC) 3-level back-to-back type voltage source converter (VSC) supplied from grid voltage of 4160V. This paper describes total loss distribution at worst case under inverter and rectifier operating mode for the power semiconductor switches. The loss analysis is confirmed through PLECS simulations. In addition, the loss factors due to di/dt snubber and ac input filter are presented. The investigation result shows that IGCT type semiconductor devices generate the total efficiency of 97.74% under the rated condition.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.359-360
• /
• 2015

10kV IGCT has been recently developed and has the potential to push wind turbine systems to higher power and voltage rating. Converters employing IGCTs need snubber and OVP circuit to limit the rate of rise of current and peak over voltage across IGCT during turn on and off state respectively. The conventional RCD snubber which is used in such power converter dissipates a significant amount of power. In order to reduce the amount of energy lost by conventional RCD snubber, this paper proposes an isolated inductor snubber circuit that not only meets all of the IGCTs characteristics during on and off-state but also significantly saves the power loss. Loss analysis of conventional di/dt snubber and OVP circuit is performed for the 3-level NPC type back-to-back VSC supplied from grid voltage of 6.9kV. In comparison with the conventional snubber, isolated inductor snubber has a fewer number of components and improved efficiency leading to a reliable and efficient wind turbine systems.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.418-424
• /
• 2001

A holographic HMD element having low aberrations and high diffraction efficiency over wide FOV has been fabricated. In order to design the HOE having low aberrations a recursive technique was used. To obtain the HOE having low aberrations as well as high diffraction efficiency over a wide FOV, we used an intermediate hologram and the grating function of the aberration corrected hologram was transferred to the final hologram through it. For the fabricated final HMD element, we got the results of spot size improved about 10 times and high diffraction efficiency over FOV of $\pm$10$^{\circ}$.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.1-3
• /
• 2019

본 논문은 연속적인 입력 전류와 낮은 스위치 전압 스트레스를 갖는 플라이백 컨버터를 제안한다. 보조 권선과 직류 차단 캐패시터를 사용하여 기존 플라이백 컨버터(CFB)의 불연속적인 입력 전류의 리플을 저감시킨다. 이를 통해 입력 전류의 di/dt를 감소시켜 낮은 EMI 특성을 갖도록 한다. 그 결과 입력 필터 크기를 줄일 수 있으며 낮은 실효 입력 전류 때문에 인공위성의 캐패시터 수명을 연장 시킬 수 있다. 또한, 하나의 스위치와 다이오드를 추가하여 스위치 전압 스트레스를 감소시킨다. 그러므로 제안 회로는 스위칭 손실이 작으며, 작은 온 저항($R_{ds(on)}$)을 갖는 스위치 적용이 가능하여 도통 손실을 저감시켰다. 본 논문에서는 제안 회로의 모드 분석과 이론적인 분석을 제시한다. 제안 회로는 현재 인공위성에 사용하는 입출력 사양인 입력 전압 50 V, 출력 전압 15V, 출력 전력 100W의 사양으로 시뮬레이션을 진행하였다. 이 결과를 통해 제안 회로의 타당성을 증명한다.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.707-714
• /
• 1996

Extraction behaviour of Np with DEHPA(di-(2-ethyhexyl)Phosphoric acid) from the low nitric acid solution(below 1M $HNO_3$) containing $H_2O_2$ as a reducing agent was studied at a batch system in order to establish the conditions of extraction and stripping and to enhance the extraction rate. As results, it was confirmed that the Np was mainly the pentavalent oxidation state in the low nitric acid solution. The extraction yield of Np was increased with increasing the concentration of DEHPA and $H_2O_2$ and decreased more rapidly with the increase of $HNO_3$ concentration. It was also found that the Np could be extracted into DEHPA even without the addiction any redox agents, although the extraction yield is rather low as about 70%. The extraction rate was proportional to the 0.516 power of $H_2O_2$ concentration and inversely proportional to 0.483 power of $HNO_3$ concentration as follows. $d[Np(V)]/dt=-1.391{\times}10^{-2}[H_2O_2]^{0.516}[HNO_3]^{-0.483}[Np(V)]$ Regardless of the $H_2O_2$, the Np extracted in the organic phase was effectively stripped to the aqueous phase with $H_2C_2O_4$. The Np could be stripped more than 92 % with 0.5M $H_2C_2O_4$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.6
• /
• pp.411-418
• /
• 2019

Light-triggered thyristors (LTTs) are essential components in high-power applications, such as HVDC transmission and several pulsed-power applications. Generally, LTT fabrication includes a deep diffusion of aluminum as a p-type dopant to form a uniform p-base region, which needs careful concern for contamination and additional facilities in silicon semiconductor manufacturing factories. We fabricated 4-inch 5,000 V LTTs with boron implantation and diffusion process as a p-type dopant. The LTT contains a main cathode region, edge termination designed with a variation of lateral doping, breakover diode, integrated resistor, photosensitive area, and dV/dt protection region. The doping concentration of each region was adjusted with different doses of boron ion implantation. The fabricated LTTs showed good light triggering characteristics for a light pulse of 905 nm and a blocking voltage (V_DRM) of 6,500 V. They drove an average on-state current (I_TAVM) of 2,270 A, peak nonrepetitive surge current (I_TSM) of 61 kA, critical rate of rise of on-state current (di/dt) of 1,010 A/㎲, and limiting load integral (I²T) of 17 MA²s without damage to the device.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.5
• /
• pp.423-431
• /
• 2001

This paper proposes a new active common-mode voltage damper circuit that is capable of suppressing a common-mode voltage produced in the PWM VSI-fed induction motor drives. The new active common mode voltage damper is consists of a four-level half-bridge Inverter and a common mode transformer with a blocking capacitor. In order to reduce the common mode voltage and high frequency leakage current the active common mode damper applies to the PWM inverter system the compensated voltage of which the amplitude is the same as the common mode voltage and of which the polarity is opposite to the common mode voltage. Simulated using P-SPICE and experimental results show that common-mode voltage damper makes contributions to reducing a high frequency leakage current and common-mode voltage.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.403-412
• /
• 2019

Aiming at the problems of large dv/dt and di/dt in traditional single-ended converters and high electromagnetic interference (EMI) noise levels, a single-ended isolated converter using the secondary resonance technique is proposed in this paper. In the proposed converter, the voltage stress of the main power switch can be reduced and the voltage across the output diode is clamped to the output voltage when compared to the conventional flyback converter. In addition, the peak current stress through the main power switch can be decreased and zero current switching (ZCS) of the output diode can be achieved through the resonance technique. Moreover, the EMI noise coupling path and an equivalent model of the proposed converter topology are presented through the operational principle of the proposed converter. Analysis results indicate that the common mode (CM) EMI noise and the differential mode (DM) EMI noise of such a converter are deduced since the frequency spectra of the equivalent controlled voltage sources and controlled current source are decreased when compared with the traditional flyback converter. Furthermore, appropriate parameter selection of the resonant circuit network can increase the equivalent impedance in the EMI coupling path in the low frequency range, which further reduces the common mode interference. Finally, a simulation model and a 60W experimental prototype of the proposed converter are built and tested. Experimental results verify the theoretical analysis.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.40-46
• /
• 2011

The synthesis of well-defined poly(styrene-b-isobutylene-b-styrene) (SIBS) triblock copolymers was accomplished by cationic sequential block copolymerization of isobutylene (IB) with styrene (St) using 1,4-di(2-chloro-2-propyl) benzene (DCC) /$TiCl_4$/2,6-di-tert-butylpyridine(DtBP) as an initiating system in methyl chloride ($CH_3Cl$)/methylcyclohexane(MeChx) (50/50 v/v) solvent mixture at $-80^{\circ}C$. The triblock copolymers exhibited excellent thermoplastic and elastomeric characteristics. Tensile strengths and Shore hardness increased with increasing polystyrene (PS) content, while elongation at break decreased. The blood-compatibility of SIBS was assessed by SEM observation of the platelet adhesion, blood clotting time and haemolysis ratio. The haemolysis ratios were below 5% which met the medical materials standard. The platelet adhesion test further indicated that SIBS block copolymers had a good blood compatibility.

• The Korean Journal of Health Service Management
• /
• v.11 no.1
• /
• pp.171-180
• /
• 2017

Objectives : The objective of this study was to compare oral health behaviors and oral health indices between regular scaling group and irregular scaling group. Methods : This study was performed at M Dental Clinic in Busan on 352 dental patients treated between January 2014 and June 2015 using V6.0 software and medical interviews. The 352 patients were divided into 3 groups and oral health behavior (OHB) and oral health indices were compared. Results : The OHB scores significantly differed among Groups C and A. Group C had the lowest number of "Bad" scores for the Simplified Debris Index (S-DI), Simplified Calculus Index (S-CI), and Simplified Oral Hygiene Index (S-OHI). Groups B and A had the lowest number of "Excellent" scores. Group C had the lowest bleeding on probing (BOP), calculus rate (CR) and decayed teeth (DT). Furthermore, Group C had the highest number of missing teeth (MT) and filled teeth (FT). Conclusions : Patients who underwent regular scaling had the highest OHB and oral health index scores. This emphasizes the importance of regular scaling for prevention and early detection of oral disease.