• Geomechanics and Engineering
• /
• 제7권3호
• /
• pp.297-316
• /
• 2014

This paper presents a detailed study focused on investigating the effects of silt content on the static and dynamic properties of sand-silt mixtures. Specimens with a low-plastic silt content of 0, 15, 30 and 50% by weight were tested in static triaxial, cyclic triaxial, and resonant columns in addition to consolidation tests to determine such parameters as compression index, internal friction angle, cohesion, cyclic stress ratio, maximum shear modulus, normalized shear modulus and damping ratio. The test procedures were performed on specimens of three cases: constant void ratio index, e = 0.582; same peak deviator stress of 290 kPa; and constant relative density, $D_r$ = 30%. The test results obtained for both the constant-void-ratio-index and constant-relative-density specimens showed that as silt content increased, the internal friction angle, cyclic stress ratio and maximum shear modulus decreased, but cohesion increased. In testing of the same deviator stress specimens, both cohesion and internal friction angle were insignificantly altered with the increase in silt content. In addition, as silt content increased, the maximum shear modulus increased. The cyclic stress ratio first decreased as silt content increased to reach the threshold silt content and increased thereafter with further increases in silt content. Furthermore, the damping ratio was investigated based on different silt contents in three types of specimens.

• 한국지반신소재학회논문집
• /
• 제15권3호
• /
• pp.1-12
• /
• 2016

본 논문에서는 지열 활용시스템을 지반구조물에 적용시 발생하는 주변 지반에 부과되는 다양한 온도 및 온도변화 사이클이 흙의 역학적 특성에 미치는 영향에 대한 내용을 다루었다. 이를 위해 화강풍화토를 대상으로 다양한 온도변화 조건을 구현하고 이에 따른 흙의 입자구조 및 열전도특성 변화 경향을 고찰하였다. 아울러 다양한 OCR(over consolidation ratio)값을 가지는 시료를 제작하여 내부 온도를 $20^{\circ}C{\sim}70^{\circ}C$까지 변화시키며 온도상승과 가열-냉각 반복작용 횟수에 따른 흙에 미치는 영향을 분석하고자 온도계로 압축셀 내부 온도를 측정하였으며 비배수 실험을 통해 시료에 작용하는 축차응력 및 간극수압을 측정하여 온도변화가 화강풍화토에 미치는 영향을 분석하였다. 그 결과 온도상승과 가열-냉각 반복 작용으로 인해 간극수압이 증가하며 축차응력 또한 감소하는 것으로 관찰되었다.

• 한국농공학회논문집
• /
• 제52권3호
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• 한국농공학회지
• /
• 제30권4호
• /
• pp.134-153
• /
• 1988

This paper was carried out to investigate the existence of a unique stress- strain behavior by obtaining some factors influencing the time dependent stress- strain behavior of clay. The results obtained from this study were summarized as follows ; 1. The relationship between stress ratro and strain in normally consolidated clay was in- dependent on pre-shear consolidation pressure. Therefore, shear strain could be expressed as a function with stress ratio. 2. The constitutive equation of shear strain on Modified Carn Clay Model coincided better with the observed value than Cam Clay Model. 3. The relationships between deviator stress and shear strain, between pore water pressure and shear strain were unified by the mean equivalent pressure. 4. The shear strain contour in norrnally consolidated clay was increased linearly through origin, but that in overconsolidated clay was not in accordance with the result of the former. 5. Because the effective stress path of normally consolidated clay was unified by the mean equivalent pressure, state boundary surface in (e,p,q) space was transformed into two dimensional surface. But it was considered to be suitable that the unified stress- strain in overconsolidated clay be expressed by a function with overconsolidation ratio. 6. The deviator for constant strain was increased linearly with increment of strain rate ($\varepsilon$) on semi-log scale, but pore water pressure was decreased. 7. The behavior of stress relaxation was transformed from linear to curvilinear with inc - rement of strain rate before stress relaxation test, and pore water pressure was increased in total range. 8. The strain of creep was increased linearly with increment of time on semi-log scale. The greater the strain rate before creep test became, the greater the increment of strain of creep became. And the pore water pressure during creep test was increased generally with increment of time on semi-log scale.

• 농업과학연구
• /
• 제12권2호
• /
• pp.309-323
• /
• 1985

본(本) 연구(硏究)는 삼축압축(三軸壓縮) 조건(條件)에서 여러 제한인자(制限因子)들이 재성형(再成形)한 해성점토(海成粘土)의 응력(應力)-변형(變形)에 미치는 영향(影響)을 알기 위하여 여러가지 단계(段階)의 함수비(含水比)와 밀도(密度)및 기타(其他)의 조건(條件)을 달리하여 실내(室內)에서 임의(任意)로 재성형(再成形)한 5가지 점토시료(粘土試料)의 비배수(非排水) 삼축압축(三軸壓縮) 시험(試驗)을 하여 다음과 같은 결과(結果)를 얻었다. 1. 함수비(含水比)의 증가(增加)와 함께 변형(變形)에 대(對)한 파괴주응력차(破壞主應力差)는 적어졌다. 2. 건조밀도(乾操密度)가 커질수록 변형(變形)에 대(對)한 파괴주응력차(破壞主應力差)는 커졌다. 3. 파괴주응력차(破壞主應力差)에 대(對)한 재성형(再成形) 함수비(含水比)와 밀도(密度)의 상호작용(相互作用)의 영향(影響)은 함수비(含水比) 6.6~9.7%와 건조밀도(乾操密度) $1.50{\sim}1.55g/cm^3$에서 가장 뚜렷했다. 4. 해성점토(海成粘土)에서는 축방향(軸方向) 변형율(變形率)이 응력(應力)-변형성질(變形性質)에 미치는 영향(影響)은 뚜렷하지 않았으나, 축방향(軸方向) 변형율(變形率)이 증가(增加)함에 따라 탄성계수율(彈性係數率)은 감소(減少)하는 경향(傾向)이 나타났다. 5. 입도(粒度)의 배합(配合)이 양호(良好)한 시료(試料)에서 변형(變形)에 대(對)한 주응력차(主應力差)가 큰 값을 나타냈다. 6. 해성점토(海成粘土)의 비배수(非排水) 변형(變形)에 관계(關係)가 깊은 인자(因子)만을 골라서 응력(應力)및 변형(變形) 예측(豫測)을 위한 중회귀(重回歸) 분석(分析) 모형(模型)을 만들 수 있다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.662-667
• /
• 1998

Recently, the using PSC with external unbonded tendons is increased. However, the behavior of external unbonded tendons is different with that of bonded internal tendon at ultimate state by compatibility condition, the slip with friction at deviator and the change of tendon eccentricity e.t.c., So, the analytical research considered the effect of these inherent characters was performed and the tendency of external unbonded tendons was estimated by numerical examples. By the analytical results, load-deflection relationship and stress increment of external unbonded tendons were similar to those of internal bonded tendon at initial elastic behavior state. Those characters were, however, smaller than those character of internal bonded tendons. For external unbonded tendons, if the 1 deviator which is positioned at maximum moment point and more 2 deviators which are position between maximum moment point and support are existed, the flexural behavior is similar to internal bonded tendons.

• 한국농공학회지
• /
• 제37권1호
• /
• pp.81-89
• /
• 1995

The aim of the work described in this paper is to develope a constitutive model for the prediction of an unsaturated Soil and to confirm the application of the model, which is composed of the elastic and plastic part in consideration of the matric suction and the net mean stress. From test results, volume changes and deviator stresses are analyzed at each state and their relationships are formulated. And the application of the model to silty sands is con- firmed by the comparison between test and predicted results. During drying-wetting and loading-unloading processes for isotropic states, the agreement between predicted and test results are satisfactory. And predicted deviator stresses are well agreed with test results in shearing process. Overall acceptable predictions are reproduced in high confining pressure. Usefulness of the model is confirmed for the unsat- urated soil except volumetric strain, which is not well agreed with the test results due to deficiency of dilatancy of the model in low confining pressure. It is, therefore, recom- mended to study the behavior of dilatancy for an unsaturated soil.

• 한국농공학회지
• /
• 제30권3호
• /
• pp.38-50
• /
• 1988

carried out to present a rheology model which is able to treat time-dependent properties of clay. The results were summarized as follow ; 1. The slope (a(e1)) of deviator stress in strain rate test was independent on axial strain, and pore water pressure was decreased with increment of strain rate. 2. The pore water pressure in a stress relaxation condition was not changed when the strain rate before stress relaxation was 0.05%/min., but it was increased with increment of time when the strain rate before stress relaxation was 0.2%/min 3. The greater the stress condition (q/qmax) and the strain rate before creep test became, the greater the increment rate of axial strain in creep test became. 4. SEKIGUCHI's constitutive equation was slightly overpredicted while empirical equation proposed in the study was well coincided with measured values. 5. The constitutive equation induced by a strain function could be dealed with a behavior of the pore water pressure increased with increment of elapsed time after primary consolidation.

• 한국지반공학회지:지반
• /
• 제11권3호
• /
• pp.43-54
• /
• 1995

실트질 모래를 재료로 삼축압축시험기를 개조하고, 삼축셀에 고압공기투과판을 부착하여 축변환기법에 의해 흡인력과 순평균응력을 조절하면서 등력압축시험과 전단시험을 행하여, 불포화 상태에 따른 토질정수의 변화를 규명하였으며, 함수상태의 변화에 따라 응력, 체적변화 등의 거동특성을 검토하였다. 실험의 결과에서 규명된 불포화토의 특성을 바탕으로, 불포화토의 응력성분을 고려하고, 수정 Cam -Clay 모델을 경계조건으로 하는 불포화토의 거동예측을 위한 구성식을 개발하고, 실트질 모래에 대한 실내실험의 자료로부터 구한 관측치와 예측치를 비교하여 이의 타당성을 검증하였다.

• Computers and Concrete
• /
• 제22권2호
• /
• pp.133-142
• /
• 2018

The deterioration of existing bridges has become a major problem around the world. In the paper, a new model and an associated stress checking method are proposed for concrete box girders strengthened by external prestressing. The new model called the spatial grid model can analyze all the spatial behaviors clearly by transforming the box girder into discrete orthogonal grids which are equivalent to plate elements. Then the three-layer stresses are employed as the stress checking indices to evaluate the stress state of the plate elements. The initial stress check before strengthening reveals the cracked and potential cracking areas for existing bridges, making the strengthening design more targeted and scientific; the subsequent stress check after strengthening evaluates the strengthening effect and ensures safety. A deficient bridge is selected as the practical example, verifying the accuracy and applicability of the proposed model and stress checking method. The results show that principal stresses in the middle layer of plate elements reflect the main effects of external prestressing and thus are the key stress checking indices for strengthening. Moreover, principal stresses check should be conducted in all parts of the strengthened structure not only in the webs. As for the local effects of external prestressing especially in the areas near anchorage and deviator, normal stresses check in the outer and inner layers dominates and local strengthening measures should be taken if necessary.