• 한국소음진동공학회논문집
• /
• 제26권7호
• /
• pp.814-819
• /
• 2016

The Stockbridge damper is used to control the aeolian vibration of a overhead transmission line due to the natural wind under a low velocity, between 1 m/s to 7 m/s. The damper model can be simply derived with several design parameters and the location of eigenvalues of design parameters are important to determine the efficiency of energy dissipation by excitation itself with two counterweights. First, the importance of resonance frequencies of Stockbridge damper was reviewed through the analysis of frequency response function of damper system. Then, the best selection of design parameters was investigated with the introduction of objected function that minimize the distance between the calculated eigenvalues and target frequency points. The best choice of design parameters was reviewed using the simulated results from the objective function and the effectiveness of selected design case was discussed at the point view of practical implementation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.7-11
• /
• 1991

The adaptive control of flexible joint manipulator is the focus of this paper. The full order flexible joint manipulator dynamic system does not allow the determination of a feedback linearization control as for rigid manipulators. This drawback is overcome by a model order reduction based on a singular perturbation strategy. The full order flexible joint manipulator dynamic model is adopted for derivation of the adaptive control law to damp out the elastic oscillations at the joints. It is shown that the joint position error will converge to zero asymptotically and that other signals remain bounded without precise knowledge of parameters of the manipulator and its joint flexibility.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.97-99
• /
• 2012

A pressure-based BOIK model considering Shock to Detonation Transition(SDT) and damage due to external fragment or bullet stimuli impact on energetic materials and analytical approach for determination of free parameters are proposed. The rate of product mass fraction(${\lambda}$) consists of ignition term that represents the initiation due to shock compression and growth term that describes propagation of detonation wave and strain term representing the morphological deformation induced by external impact.

• International Journal of Concrete Structures and Materials
• /
• 제10권2호
• /
• pp.163-175
• /
• 2016

This paper presents a revised procedure for computation of double-K fracture parameters of concrete split-tension cube specimen using weight function of the centrally cracked plate of finite strip with a finite width. This is an improvement over the previous work of the authors in which the determination of double-K fracture parameters of concrete for split-tension cube test using weight function of the centrally cracked plate of infinite strip with a finite width was presented. In a recent research, it was pointed out that there are great differences between a finite strip and an infinite strip regarding their weight function and the solution of infinite strip can be utilized in the split-tension specimens when the notch size is very small. In the present work, improved version of LEFM formulas for stress intensity factor, crack mouth opening displacement and crack opening displacement profile presented in the recent research work are incorporated. The results of the double-K fracture parameters obtained using revised procedure and the previous work of the authors is compared. The double-K fracture parameters of split-tension cube specimen are also compared with those obtained for standard three point bend test specimen. The input data required for determining double-K fracture parameters for both the specimen geometries for laboratory size specimens are obtained using well known version of the Fictitious Crack Model.

• 한국농공학회논문집
• /
• 제52권6호
• /
• pp.19-26
• /
• 2010

Batch experiments were conducted to investigate growth and nutrient removal performance of microalgae Chlorella vulgaris by using piggery wastewater in different concentration of pollutants and the common growth models (logistic, Gompertz and Richards) were applied to compare microalgal growth parameters. Removal of nitrogen (N) and phosphorus (P) by Chlorella vulgaris showed correlation with biomass increase, implying nutrient uptake coupled with microalgae growth. The higher the levels of suspended solids (SS), COD and ammonia nitrogen were in the wastewater, the worse growth of Chlorella vulgaris was observed, showing the occurrence of growth inhibition in higher concentration of those pollutants. The growth parameters were estimated by non-linear regression of three growth curves for comparative analyses. Determination of growth parameters were more accurate with population as a variable than the logarithm of population in terms of R square. Richards model represented better fit comparing with logistic and Gompertz model. However, Richards model showed some complexity and sensitivity in calculation. In the cases tested, both logistic and Gompertz equation were proper to describe the growth of microalgae on piggery wastewater as well as easy to application.

• 한국측량학회지
• /
• 제23권1호
• /
• pp.59-67
• /
• 2005

본 연구에서는 위성영상의 RPC 카메라 모델로부터 외부표정요소 결정방법을 제안하였다. 제안한 방법을 이용하여 SPOT 위성영상을 이용한 선행실험을 한 결과, RPC로부터 결정된 외부표정요소와 원래의 외부표정요소의 차이는 미소하였으며, 지상좌표 추출에 있어서도 거의 유사한 결과 정확도를 얻었다. 그리고 제안한 방법을 IKONOS 위성의 Geo레벨 입체영상에 적용한 후, RPC 블럭조정방법에 의한 위치결정 정확도와 비교한 결과, 유사한 결과를 나타냈으며, 두 방법으로 획득한 샘플지역의 DEM 또한 큰 차이를 보이지 않았다.

• 대한기계학회논문집A
• /
• 제21권3호
• /
• pp.369-377
• /
• 1997

The torque converter, a major part of automatic transmissions, has many difficulties in analysis due to the factors such as power transmission through fluid flow, complex internal geometry, and various operating conditions. Because of such difficulties, the dynamic analysis and design of a torque converter are generally carried out by using equivalent performance model which is based on the concept of mean flow path. Since the design procedures of a torque converter are essential technology of automotive industry, the details of the procedures are rarely published. In this study, the basic design procedures of a torque converter are systemized and coded based on the equivalent performance model. The mathematical methods to deal with mean flow path determination and the core-shape are developed. And by using this model, the method of determination of performance parameters satisfying the requested performance is proposed. Finally, to embody the three-dimensional shape, the intermediate blade angles which maximize the tractive performance are determined and laid out.

• 한국측량학회지
• /
• 제13권2호
• /
• pp.117-124
• /
• 1995

본 연구는 GPS위성측량의 기준좌표계로 채택된 세계측지계(WGS-84)와 현재 우리나라에서 사용되고 있는 베셀타원체에 근거한 측지계와 좌표변환을 위하여 Bursa-Wolf모델, Molodensky-Badekas모델과 Veis모델의 3가지 7-매개변수 좌표변환 방법을 수행하고 좌표변환 정밀도를 비교하였다. 본 연구의 결과, 우리나라에서는 Bursa-Wolf 모델이 7-매개변수 결정모델로 적합하다는 것을 알 수 있었다.

• Journal of Information Technology Applications and Management
• /
• 제27권3호
• /
• pp.69-75
• /
• 2020

In this paper, we applied the shape parameters of the exponentialized exponential life distribution widely used in the field of software reliability, and compared the reliability properties of the software using the non-homogeneous Poisson process in finite failure. In addition, the average value function is also a non-decreasing form. In the case of the larger the shape parameter, the smaller the estimated error in predicting the predicted value in comparison with the true value, so it can be regarded as an efficient model in terms of relative accuracy. Also, in the larger the shape parameter, the larger the estimated value of the coefficient of determination, which can be regarded as an efficient model in terms of suitability. So. the larger the shape parameter model can be regarded as an efficient model in terms of goodness-of-fit. In the form of the reliability function, it gradually appears as a non-increasing pattern and the higher the shape parameter, the lower it is as the mission time elapses. Through this study, software operators can use the pattern of mean square error, mean value, and hazard function as a basic guideline for exploring software failures.

• Computers and Concrete
• /
• 제9권2호
• /
• pp.81-97
• /
• 2012

This paper presents development of double-K fracture model for the split-tension cube specimen for determining the unstable fracture toughness and initial cracking toughness of concrete. There are some advantages of using of split-tension cube test like compactness and lightness over the existing specimen geometries in practice such as three-point bend test, wedge splitting test and compact tension specimen. The cohesive toughness of the material is determined using weight function having four terms for the split-tension cube specimen. Some empirical relations are also suggested for determining geometrical factors in order to calculate stress intensity factor and crack mouth opening displacement for the same specimen. The results of double-K fracture parameters of split-tension cube specimen are compared with those obtained for compact tension specimen. Finally, the influence of the width of the load-distribution of split-tension cube specimen on the double-K fracture parameters for laboratory size specimens is investigated. The input data required for determining double-K fracture parameters for both the specimen geometries are obtained using well known version of the Fictitious Crack Model.