• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.4
• /
• pp.246-250
• /
• 2014

Large mutual capacitance touch screen panels (TSP) are susceptible to display and ambient noise. This paper presents a multi-touch detection algorithm using an efficient noise compensation technique for large mutual capacitance TSPs. The sources of noise are presented and analyzed. The algorithm includes the steps to overcome each source of noise. The algorithm begins with a calibration technique to overcome the TSP mutual capacitance variation. The algorithm also overcomes the shadow effect of a hand close to TSP and mutual capacitance variation by dynamic threshold calculations. Time and space filters are also used to filter out ambient noise. The experimental results were used to determine the system parameters to achieve the best performance.

• Convergence Security Journal
• /
• v.9 no.2
• /
• pp.41-48
• /
• 2009

Distributed denial of service attack detection for more development and research is underway. The method of using statistical techniques, the normal packets and abnormal packets to identify efficient. In this paper several statistical techniques, using a mix of various offers a way to detect the attack. To verify the effectiveness of the proposed technique, it set packet filtering on router and the proposed DDoS attacks detection method on a Linux router. In result, the proposed technique was detect various attacks and provide normal service mostly.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.3
• /
• pp.200-206
• /
• 2005

In this paper, a redundancy management system for aircraft is studied, and FDI (Fault Detection and Isolation) algorithm of inertial sensor system is proposed. UAV system cannot allow triple or quadruple hardware redundancy due to the limitations on space and weight. In the UAV system with dual sensors, it is very difficult to identify the faulty sensor. Also, conventional FDI method cannot isolate multiple faults in a triple redundancy system. In this paper, hardware based FDI technique is proposed, which combines a parity equation approach with the wavelet based technique, which is a model-free FDI method. To verify the effectiveness of the proposed FDI method, numerical simulations are performed.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1683-1684
• /
• 2008

For direct detection of microbes in air, samples have to be collected but environmental particles such as dust are also trapped in such samples. Therefore the isolation of target bacteria from non-biological materials of similar size is of great importance in the identification of such organisms. Dielectrophoresis is an emerging technique that can rapidly separate cells in microfluidics. In this paper we proposed a new method for the separation of airborne microbes using condensation and dielectrophoresis. This system could be used as a continuous flow through separation system for various particles and utilized as a pretreatment technique for microbe detection.

• Journal of Multimedia Information System
• /
• v.7 no.1
• /
• pp.17-24
• /
• 2020

Rice (Oryza Sativa) is an important source of food for the people of our country, even though of world also .It is also considered as the staple food of our country and we know agriculture is the main source country's economy, hence the crop of Rice plays a vital role over it. For increasing the growth and production of rice crop, ground-breaking technique for the detection of any type of disease occurring in rice can be detected and categorization of rice crop diseases has been proposed in this paper. In this research paper, we perform comparison between two classifiers namely MDC and Bayes' classifiers Survey over different digital image processing techniques has been done for the detection of disease in rice crops. The proposed technique involves the samples of 200 digital images of diseased rice leaf images of five different types of rice crop diseases. The overall accuracy that we achieved by using Bayes' Classifiers and MDC are 69.358 percent and 81.06 percent respectively.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1104-1113
• /
• 2000

This paper proposes an efficient reverse engineering technique for compound surfaces using a boundary detection method. This approach consists in extracting geometric edge information using a vision system, which can be used in order to drastically reduce geometric errors in the vicinity of compound surface boundaries. Through the image-processing technique and the interpolation process, boundaries are reconstructed by either analytic curves (e. g. circle, ellipse, line) or parametric curves (B-spline curve). In other regions, except boundaries, geometric data are acquired on CMM as points inspected using a touch type probe, and then they are interpolated on several surfaces using a B-spline skinning method. Finally, the boundary edge and the skinned surfaces are combined to reconstruct the final compound surface. Through simulations and experimental works, the effectiveness of the proposed method is confirmed.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.114-121
• /
• 1995

An ultrasonic technique using normal-incident compressional waves was used to evaluate the surface and subsurface damage in ceramics produced by Hertzian indentation. Damage was produced by a blunt indenter (tungsten carbide ball) in glass-ceramic, green glass and silicon nitride. The damage was classified into two types; (1) Hertzian cone crack, in green glass and fine grain silicon nitride, and (2) distributed subsurface micro fractures, without surface damage, produced in glass ceramic. The ultrasonic technique was successful in detecting cone craks. The measurement results with the Hertzian cone cracks indicated that cracks perpendicular to the surface could be detected by the normal-incident compressional waws. Also shown is the capability of normal-incident compressional waves in detection distributed micro-sized cracks size of subsurface microfractures.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.9
• /
• pp.828-833
• /
• 2010

Steam leakage is one of the major issues for the structural fracture of pipes of nuclear power plants. Therefore a method to inspect a large area of piping systems quickly and accurately is needed. In this paper, we proposed the method for the detecting steam leakage by using image signal processing. Our basic idea come from heat shimmer which shine with a soft light that looks as if it shakes slightly. To test the performance of this technique, experiments have been performed for simple heat source and steam generator. Results show that the proposed technique is quite powerful in the steam leak detection.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.223-229
• /
• 2003

Tool wear monitoring is an important technique in the flexible manufacturing system. This paper studies the end mill wear detection using CCD camera and pattern recognition method. When the end mill working in the machining center, the bottom edge of the end mill geometry change, this information is used. The CCD camera grab the new and worn tool geometry and the area of the tool geometry was compared. In this result, when the values of the subtract worn tool from new tool end in 200 pixels, it decides the tool life. This paper proposed the new method of the end mill wear detection.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.1
• /
• pp.345-359
• /
• 2017

Optical Character Recognition (OCR) that has been a main research topic of computer vision and artificial intelligence now extend its applications to detection of text area from video or image contents taken by camera devices and retrieval of text information from the area. This paper aims to implement a binarization algorithm that removes user intervention and provides robust performance to outdoor lights by using TopHat algorithm and channel transformation technique. In this study, we particularly concentrate on text information of outdoor signboards and validate our proposed technique using those data.