• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.349-356
• /
• 2014

As the turns ratio of the tapped-inductor contributes to the step-up ratio, the tapped-inductor boost (TIB) converter has significantly increased level of difficulties in its analysis and design compared to the conventional boost converter where the duty ratio is the sole factor affecting the step-up ratio. In this paper, the operation of the continuous current mode TIB converter is briefly reviewed, the characteristics are analyzed in detail, and a design guideline optimizing the loss in the tapped-inductor is presented with a practical design example. Finally, experimental results from a 12V/120V prototype for 0.25A LED driver application are also presented to confirm the design.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.475-481
• /
• 2019

The importance of performance-based design feedback is being emphasized when it comes to the potential impact that affects all the lifecycle of the building. However, the latency and disconnection of domain expert in the sector of AEC/FM remain current obstacles between design and performance feedback. It is hard to utilize performance feedback information for design exploration and support design decision making during the conceptual phase of design. Using parametric design, this paper proposes various design alternatives from a set of rules and constraints defined by algorithms for the geometric configurations of an Office Building. A Building Performance Analysis (BPA) was to developed using Autodesk® Revit® 2019 which integrates Autodesk® Green Building Studio® to predict its sufficient daylighting conditions of the LEED v4's Daylighting Autonomy (DA). The parametric-based performance feedback of this study outlines potential design improvements for further exploration in application to the early design process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.677-686
• /
• 2016

A thermal power plant is the first CFBC (Circulating Fluidized Bed Combustion) power plant consisting of 2 boilers-1 turbine. The optimal height of a stack needs to be approximately 156 meters in the case of this thermal power plant; however, the thermal power plant sites satisfy a function and reduce the construction cost by using mountains in the sites after cutting the ground and locating an integrated office and chimney at an altitude of 70 meters thereby lowering the height of the stack to 86 meters. In addition, the integrated office, which has a combined stack style with a unique design, is constructed by connecting with 2 stacks and disposing the office and an observatory in the space between them. Therefore, this study examined the design concept that fulfils the structural, functional, and aesthetic factors, harmoniously by joining the integrated office and the stack, which are disparate, and investigated special construction methods (Slip Form, Steel Inner Flue & Lift-up) through which heterogeneous architectures are structurally, functionally, and aesthetically constructed.

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.57-57
• /
• 2004

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.07a
• /
• pp.525-526
• /
• 2006

Ethernet Passive Optical Networks (EPON) are an emerging access network technology that provide a low-cost method of deploying optical access lines between a central office (CO) and a customer site. This paper shows that subscriber unit manages traffic data between a central office (CO) and a customer site in economic solution.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.100-103
• /
• 2005

This work discusses the numerical analysis, the design and experimental test of the SMA (Shape Memory Alloy) actuator along with its capabilities and limitations. Convection heating and cooling using water actuate the SMA element of the actuator. The fuel such as propane, having a high energy density, is used as the energy source for the SMA actuator in order to increase power and energy density of the system, and thus in order to obviate the need for electrical power supplies such as batteries. The system is composed of a pump, valves, bellows, a heater (burner), control unit and a displacement amplification device. The actuation frequency is compared with the prediction obtained from numerical analysis. For the designed SMA actuator system, the results of numerical analysis were utilized in determining design parameters and operating conditions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.967-975
• /
• 2009

In order to control differential settlement and to secure the safety of super structure on a high rock embankment the designed static compaction is changed with dynamic compaction and piled raft method. The parameters for dynamic compaction design are obtained from a pilot test. In addition, numerical analyses are also carried out to figure out the length and quantity of piled raft that can restraint the differential settlement within allowance range.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2001.05a
• /
• pp.144-148
• /
• 2001

The structures built carelessly become the origin of a serious environmental problem caused from the urbanization. To solve this problem, I have considered the characteristics of Atrium as an environment-friendly factor to the office environment. The result is that Atrium protects the insiders health and contributes to the energy saving as it enables the use of natural lights and solar heat first. Second, it gives the office environment liveliness, makes a clean environment and helps the insiders health for introduction of green field. Third, it plays a role of a place for rest, a place for meeting, and a small park by attracting people to the organic space where the inside and outside are connected with a huge glass. On the basis of these characteristics, we should try to prepare the complementary relationship between human beings and nature mutually through its active introduction in the space.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.8
• /
• pp.23-34
• /
• 2019

The façade, a fundamental function as a skin that protects human life from external environment such as cold and hot weather, snow, rain, and wind, etc, has served as a media for communication between indoor space of the building and outside space. From the media for communication point of view, the approach to envelope design, in which environmental elements are transmitted internally through the filtering of external environments, has been evolving in various ways from the past to the present. Today, modern architecture technologies including curtain wall systems and user-friendly computer programming and environmental analysis programs demonstrate a differentiated approach to envelope design related to the indoor environment. For this reason, it is worth noting that the envelope design factors and trends that appear variously in the UNStudio's projects before and after the 2000s. The factors reflected in the envelop design in conjunction with the indoor environment obtained through the case study of the UNStudio's office projects were daylight environment, thermal environment, ventilation, noise, privacy and view, and consideration for daylight environment and thermal environment was reflected in many cases through the case study. Looking at the changes in the diagrams in order of year, it can be seen that the envelope design using the environmental analysis tool has been performed since 2006. This is a clue to show the envelop design changes from the conceptual method to the data-based one. The diagrams and analysis results related to the envelop design showed that the thermal environment related to solar radiation was the most, and no diagrams and analysis related to the indoor illumination were found. Since 2010, PV panel installation has been shown in the envelope design, which can be found in the increased efficiency of PV panels due to the technological advances and the decrease in production cost.

• Korean Architects
• /
• s.554
• /
• pp.96-97
• /
• 2015

지난 편에서는 parametric design의 발생과 흐름에 대해 간략하게 이야기 해 보았습니다. 이번 편에서는 parametric design을 하기 위해 고안된 여러 가지 parametric tool들이 바탕을 두고 있는 기본적인 개념 및 그 구성요소 등에 대해 간략하게 이야기를 해보고자 합니다.