• E2M - 전기 전자와 첨단 소재
• /
• 제7권6호
• /
• pp.511-519
• /
• 1994

The effect of the deposition conditions, such as the base pressure, working pressure, sputtering power, pre-sputtering, and deposition thickness in facing targets sputtering system(FTS), on the oxidation of the TbFeCo thin films was studied by investigating the magneto-optical properties as well as oxygen analysis by the AES depth profiles. The results showed that the base pressure did not affect the magnetic properties so much, probably due to the short flight distance of the sputtered particles. At the higher sputtering power and lower working pressure with pre-sputtering the oxidation of TbFeCo thin films was decreased. As the film thickness increased the TbFeCo thin films showed the perpendicular anisotropy from in-plane anisotropy overcoming the oxidation effect at the beginning of the sputtering.

• 한국세라믹학회지
• /
• 제29권4호
• /
• pp.319-327
• /
• 1992

Sb-doped SnO2 films were formed on Corning glass 7059 substrate by chemical vapor deposition using simulataneous hydrolysis of SnCl4 and SbCl5. Fairly good transparent conducting film with a low resistivity of ~6$\times$10-4{{{{ OMEGA }}cm and high average optical transparency above ~85% in the range of visible light was obtained at the deposition condition of 50$0^{\circ}C$ and input-gas ratio, [Psbcl5/Psncl4] of 0.05. Film conductivity was improved without loosing optical transparency at light doping of Sb and found to be due to the increase of electron concentration. However, high doping of Sb into SnO2 film largely deteriorated conductivity, optical transparency and crystallinity of the film.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.21.1-21.1
• /
• 2011

Vertically aligned single-crystal ZnO nanowires have been successfully grown on c-plane sapphire substrate using chemical vapor deposition (CVD) without catalyst. According to growth temperatures, it was changed ZnO growth characteristic. We investigated the effect of substrate temperatures on the growth ZnO films or nanowires on c-plane (0001) sapphire substrates. The ZnO films were acquired at $500^{\circ}C$, whereas the ZnO nanowires were obtained at $600^{\circ}C$, $700^{\circ}C$, and $800^{\circ}C$. The growth behavior diameter and growth rate of ZnO were changed due to different temperature. As a result of analyzing in-plane residual stress by X-ray diffraction, the optimized condition of ZnO nanowires were at $600^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.344-347
• /
• 2014

This study was carried out on DLC thin film deposition technology used in infrared optical system production as a method of reducing the shape changes of the molding core and the consequent loss of life. Experiments on the deposition on silicon wafer and tungsten carbide used as a substrate for molding core were conducted at each processing condition using a filtered arc system, and it was found that the surface and mechanical properties were of the greatest quality when the substrate bias voltage of -150 V was used. In addition, it was confirmed that the PV and Ra characteristics were improved by the deposition of the DLC thin film.

• 전기학회논문지
• /
• 제58권8호
• /
• pp.1566-1571
• /
• 2009

The discharge electrodes in ac PDP are coated with dielectric layer, and transparent MgO thin films are deposited on the dielectric layer. The main role of the MgO thin films in ac PDP is to protect the dielectric layer from sputtering by ion bombardment in the glow-discharge plasma. An additional important role of the MgO thin film is the high secondary electron emission coefficient which leads the low firing voltage and low cost of the PDP. In this paper, we investigated the relations of the crystal orientation about deposition thickness, deposition rate, temperature of substrate, and distance between the MgO tablet and the substrate. Additionally, we investigated the discharge characteristics of the AC PDP using nano-powder MgO tablet

• 전자공학회논문지A
• /
• 제29A권8호
• /
• pp.49-55
• /
• 1992

We Have investigated the properties of the titanium nitrite films widely used in VLSI devices as diffusion barrier in Al-based metallization. TiN films were formed by reactive sputtering from Ti target in Ar-N$_2$ mixtures, varying deposition parameters such as N$_2$ partial pressure, substrate temperature, power, and total pressure. All the samples received the heat treatment at 45$0^{\circ}C$ for 30 min. The resulting films are characterized by mechanical stylus($\alpha$-step), x-ray diffraction(XRD), scanning electron microscopy(SEM), and four point probe method. The Tin film properties strongly depend on the deposition condition. The stoichiometry and Ti deposition rate are critically affected by nitrogen partial pressure, and the resistivity, in particular, is dependent on both the substrate temperature and sputtering power.

• 산업기술연구
• /
• 제35권
• /
• pp.89-94
• /
• 2015

Graphene is a carbon-based two dimensional honeycomb lattice with monoatomic thickness and has attracted much attention due to its superior mechanical, electronic, and physical properties. Here, we present a synthesis of high quality graphene on Pt substrate using a chemical vapor deposition (CVD). We optimized synthesis condition with various parameters such as synthesis temperature, time, and cooling rate. Based on the results, we concluded that graphene synthesis is driven by mainly carbon adsorption on surface rather than precipitation of carbon which is dominant in other metal substrate. In addition, Pt substrate can be repeatedly used several times with high quality graphene.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권8호
• /
• pp.927-933
• /
• 2006

The structural and electrical characteristics of PLZT thin films fabricated onto $Pt/IrO_2/Ir/Ti/SiO_2/Si$ substrates by a pulsed laser deposition were investigated to develop the high dielectric thin films for capacitor layer of semiconductor memory devices The slim region 14/50/50 PLZT thin films were fabricated by PLD and estimated the characteristics for memory application 14/50/50 PLZT thin films have crystallize into perovskite structure at the $600^{\circ}C$ deposition temperature, 200 mTorr of oxygen pressure, and 2 $J/cm^2$ of laser energy density. In this condition PLZT thin films had the dielectric constant as high as 985, storage charge density 8.17 ${\mu}C/cm^2$ and charging time 0.20 ns. Leakage current density was less than $10^{-10}A/cm^2$ up to 5 V bias voltage.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.421-421
• /
• 2012

Graphene has drawn enormous attention owing to its outstanding properties, such as high charge mobility, excellent transparence and mechanical property. Synthesis of Graphene by chemical vapor deposition (CVD) is an attractive way to produce large-scale Graphene on various substrates. However the fatal limitation of CVD process is high temperature requirement(around $1,000^{\circ}C$), at which many substrates such as Al substrate cannot endure. Therefore, we propose plasma enhanced CVD (PECVD) and decrease the temperature to $400^{\circ}C$. Fig. 1 shows the typical structure of RF-PECVD instrument. The quality of Graphene is affected by several variables. Such as plasma power, distance between substrate and electronic coil, flow rate of source gas and growth time. In this study, we investigate the influence of these factors on Graphene synthesis in vacuum condition. And the results were checked by Raman spectra and conductivity measurement.

• 한국세라믹학회지
• /
• 제24권2호
• /
• pp.170-178
• /
• 1987

Changes of the properties of PECVD-SiN film with the variation of deposition process parameters were investigated and optimum process parameters were determined. The refractive index of the film increased with increasing substrate temperature and pressure, and decreasing rf-power, NH3/SiH4 gas ratio and total gas flow. BHF etch rate and deposition rate show a decreasing tendency with increasing refractive index. The step coverage of the film was not affected much by deposition rate and pressure, but improved apparently with increasing rf-power and NH3/SiH4 gas ratio. Also the optimum process parameters were determined by considering the characteristic properties as well as thickness uniformity of films. The refractive index of the film deposited under this condition was 2.06.