• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.347-349
• /
• 2016

본 논문에서는 dopant density에 의존적인 pn junction의 breakdown 특성을 향상시키기 위하여, doping density와 doping profile에 대하여 분석했다. Doping density와 doping profile은 역방향 junction breakdown voltage를 결정하는 중요한 요소인 공핍영역의 두께와 공핍영역 내에 인가되는 electric field를 결정한다. Uniform doping profile과 Gaussian doping profile을 비교했고, 고전압 환경에서 사용할 수 있는 소자를 제작하는데 더욱 적절한 doping profile과 doping 농도에 대해 기술했다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.7
• /
• pp.52-58
• /
• 2013

The two-dimensional finite difference time domain algorithm is used to numerically reconstruct the electron density profile in O-mode ultrashort pulse reflectometry. A Gaussian pulse is employed as the source of a probing electromagnetic wave. The Gaussian pulse duration is chosen in such a manner as to have its frequency spectrum cover the whole range of the plasma frequency. By using a number of numerical band-pass filters, it is possible to compute the time delays of the frequency components of the reflected signal from the plasma. The electron density profile is reconstructed by substituting the time delays into the Abel integral equation. As a result of simulation, the reconstructed electron density profile agrees well with the assumed profile.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.60-67
• /
• 2011

A repeated impregnation and carbonization process was introduced to product high-density woodceramics using a resin impregnation board. The density profile were measured to further confirm morphologically and structurally occurred changes of one-time and two-time phenolic resin-treated and carbonized woodceramics. After the two-time carbonization of the products, the minimum, average and maximum densities increased more than those of the one-time carbonized woodceramics, and the increase of density profile. Therefore, it is considered that the preparation of uniformed woodceramics with high-density and low density dissipation can be produced by a repeated impregnation and carbonization).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.5
• /
• pp.483-489
• /
• 2002

The computer simulation has been done for non-insulated and insulated pipes which are vacant or half filled with liquid. The simulation results showed that the density profile on the radiography is continuous and symmetrical around the center of pipe in the case of vacant pipe. On the other hand the density profiles are not symmetrical and depend on geometrical setting for radiography in the case of half filled pipes. Finally, experimental testing on a non-insulated carbon steel pipe with artificial notches of different depth is carried out using Ir-192 and industrial film. Comparing the measured density profile on the radiograph to the calculated one, it has been shown that it is possible to evaluate thickness variation by measuring density profile on a radiograph.

• Biomolecules & Therapeutics
• /
• v.16 no.3
• /
• pp.293-298
• /
• 2008

Cirsium japonicum water extracts has been used to treat vascular related diseases. We have previously reported that Cirsium japonicum extracts activated estrogen receptors. It is widely known that estrogen increases the high density lipoprotein cholesterol and decrease the low density lipoprotein cholesterol on the lipid profile. But effects of Cirsium japonicum on lipid profile are not reported yet. Therefore, we have studied the effects of Cirsium japonicum on the lipid content in ovariectomized rats. Thirty Sprague-Dawley (SD) rats of $210{\pm}20\;g$ were studied for 10 weeks. The rats were divided into five groups; (I) sham, no ovariectomized rats plus olive oil, (II) ovariectomized rats plus olive oil, (III) ovariectomized rats plus 0.5 mg/kg $17{\beta}$-estradiol (E2) in olive oil, (IV) ovariectomized rats plus 0.5 mg/kg Cirsium japonicum in olive oil, and (V) ovariectomized rats plus 5 mg/kg Cirsium japonicum in olive oil. Treatment with Cirsium japonicum or E2 induced significant reduction in total cholesterol, low density lipoprotein cholesterol/total cholesterol, total cholesterol/high density lipoprotein cholesterol and low density lipoprotein cholesterol/high density lipoprotein cholesterol compared to control group as well as increase in uterine weight. However, changes in triglycerides levels were different. Our results suggest that Cirsium japonicum is functionally similar to E2 in vivo as well as in vitro.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.157-161
• /
• 2004

We present a simple analytical expression of plasma density by making use of the electron density equation to study the dynamic behavior of the corona discharge plasma. It assumes that a specified voltage profile is fed through the inner conductor of the reactor chamber consisting of two coaxial conducting cylinders. The analytical description is based on the electron continuity equation with ionization and attachment by electrons. It is found that the electron density profile calculated between two coaxial cylindrical electrodes depends very sensitively on the Profile of applied voltage. The analytical expression of plasma density and its generation will provide important scaling laws in the corona discharge plasma.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.44-53
• /
• 2006

In this study, the non-destructive computed tomography was adopted to observe the density profile of the needle-punched Carbon/Carbon(C/C) composites nozzle throat. The density profile of C/C was evaluated within ${\pm}0.01g/cm^3$ with 98.74% confidence when the correction of the image and high signal-to-noise ratio were achieved by the optimization of the beam hardening, the electrical noise and the scattered X-ray. The density variation of C/C with the computed tomography was in good agreement with the results obtained by the water immersion method and the observation with scanning electron microscope.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.2
• /
• pp.98-108
• /
• 2023

In this study, the boards were manufactured according to the mandarin peels addition rate using sawdust and mandarin orange peel. After that, the mechanical properties and density profile of ceramics prepared by conditions through resin impregnation process and carbonization process were investigated. The bending and compression strengths of ceramics tended to increase as the resin impregnation rate increased. When the resin impregnation rate was 70%, the highest values were 8.58 MPa and 14.77 MPa, respectively. Also, the mechanical properties of ceramics according to carbonization temperature showed the highest values at 1,200℃ for bending strength of 11.09 MPa and compression strength of 17.20 MPa. The bending strength and compression strength according to the mandarin peels addition rate showed the highest values at 8.62 MPa and 14.16 MPa, respectively, when the mandarin orange peel addition rate was 5%. The mechanical properties tended to decrease when the addition rate of mandarin orange was increased. The density profile of ceramics showed a similar tendency to the mechanical properties. It can be seen that the density distribution from the surface layer to the center layer is more uniform as the resin impregnation rate and carbonization temperature increase and the mandarin peels addition rate decreases.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.482-488
• /
• 2012

To fabricate a precise micro metal mold, the electrochemical etching process has been researched. We investigated the electrochemical etching process numerically and experimentally to determine the etching tendency of the process, focusing on the current density, which is a major parameter of the process. The finite element method, a kind of numerical analysis, was used to determine the current density distribution on the workpiece. Stainless steel(SS304) substrate with various sized square and circular array patterns as an anode and copper(Cu) plate as a cathode were used for the electrochemical experiments. A mixture of $H_2SO_4$, $H_3PO_4$, and DIW was used as an electrolyte. In this paper, comparison of the results from the experiment and the numerical simulation is presented, including the current density distribution and line profile from the simulation, and the etching profile and surface morphology from the experiment. Etching profile and surface morphology were characterized using a 3D-profiler and FE-SEM measurement. From a comparison of the data, it was confirmed that the current density distribution and the line profile of the simulation were similar to the surface morphology and the etching profile of the experiment, respectively. The current density is more concentrated at the vertex of the square pattern and circumference of the circular pattern. And, the depth of the etched area is proportional to the current density.

• The Journal of Korean Institute of Information Technology
• /
• v.17 no.4
• /
• pp.87-97
• /
• 2019

SRS was proposed for immediate processing of the meaning of sensor data on mobile devices independent from specific sensor networks and sensor type. However, each time new sensor data is received, sensor data inspection operations are performed repeatedly, and it cause resulting in low performance. App profile-based SRS has been proposed to resolve the problem. The app profile-based SRS has improved the SRS problem through the profile, but has been tested in a virtual simulation environment. After that the test was experimented in a real-time environment, but has not been tested with a variety of dynamic factors. Therefore, this paper experiment considering such as user mobility and sensor density in real-time environment. And this paper also evaluate performance of the App profile-based through analysis of the results of the experiment. As a result, app profile-based SRS is high influence by density and sensor type, and the number of sensor node is not influence.