• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.182-183
• /
• 2017

This research identifies radon gas absorption mechanism by adsorption materials, replacing gypsum board with radon emissions, the density and absorption rates of magnesium were carried out using vermiculite, anthracite, powdered active carbon, bentonite, illite, diatomite as a basic study on the fire resistance type of radon Gas reduction type with absorption and decomposition. As a result of the experiment, diatomite showed the lowest density, and the highestt value was the highest. For the absorption rate, bentonite showed the highest absorption rate, and the anthracite showed the lowest absorption rate.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.245-249
• /
• 2015

Vertically coupled low density InGaAs quantum dots (QDs) buried in GaAs matrix were grown with migration enhanced molecular beam epitaxy method as a candidate for quantum information processing devices. We performed excitation power-dependent photoluminescence measurements at cryogenic temperature to analyze the effects of vertical coupling according to the variation in thickness of spacer layer. The more intense coupling effects were observed with the thinner spacer layer, which modified emission properties of QDs significantly. The low surface density of QDs was observed by atomic force microscopy, and scanning transmission electron microscopy verified the successful vertical coupling between low density QDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.9-12
• /
• 1994

Epoxy-Ceramic Composite have good insulating, therma1 and mechanical properties, so it is studied actively on this material. In this thesis, we made a composite material b)\ulcorner filling Epoxy Resin with ceramics treated with Sillane Coupling Agent and studied dielectric and insulating characteristics according to treatment density of Sillane Coupling Agent and weight percent of filler. As a result, loss tangent increase and electrical breakdown voltage decrease according to increasing treatment density of sillane coupling agent because Interface matching between matrix and filler is not good. The best treatment density of sillane coupling agent is 0.5% water solution, in this density the best interface matching is achieved so good dielectric and insulation characteristics are shown. Dielectric and insulation characteristics according to weight percent of filler are best at 25wt.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.385-386
• /
• 2006

For attaining optimum fatigue resistance of PM steels, high density levels are necessary. In this work, sintered steels Fe-1.5%Mo-0.6%C and Fe-1.5%Cr-0.2%Mo-0.6%C were produced with density levels of 7.1 to $7.6\;g.cm^{-3}$. Ultrasonic fatigue testing with 20 kHz was performed in push-pull mode up to 10E9 cycles. It was shown that the fatigue endurance strength is strongly improved by higher density levels, but also higher sintering temperatures are beneficial. The Cr-Mo steels proved to be superior to the plain Mo alloyed, due to a more favourable as-sintered matrix microstructure.

• Korean Journal of Veterinary Research
• /
• v.30 no.4
• /
• pp.373-381
• /
• 1990

Endocrine cells in the cardiac and fundic regions of the Korean hedgehog were studied ultrastructurally. Five types of endocrine cells classified as EC, ECL, $D_1$. G and A-like cells were identified in these regions. EC cells contained pleomorphic granules, 170~500nm in diameter, with high electron density and highly dense bodies in a dense matrix. ECL cells were characterized by the presence of round or oval granules, 220~450nm in diameter, with high electron density. Some granules of ECL cells showed a small amounts of contents or empty. $D_1$ cells contained round and relatively small granules, 140~400nm in diameter, with low to moderate electron density. G cells were characterized by the presence of round or oval granules, 200~400nm in diameter, with moderate electron density. Some granules of these cells showed a narrow halo between the limiting membrane and the granular matrix. A-like cells contained round granules, 170~260nm in diameter, With high electron density. The granules of these cells showed homogeneous matrix surrounded by the tight membrane.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.31 no.6
• /
• pp.481-491
• /
• 2005

Purpose: The aim of the present study is to evaluate the effect of autogenous bone and allograft material coverd with a bioresorbable membrane on bone regeneration after a simultaneous installation of implant. Materials and methods: Twelve healthy rabbits, weighing about $3{\sim}4$ kg, were used in this experiment. Following impalnt(with 3.25 mm diameter and 8 mm length) site preparation by surgical protocol of $Oraltronics^{(R)}$, artificial bony defect, 5mm sized in height and depth, was created on femoral condyle using trephine drill(with 5 mm diameter and 5 mm length). Then implant was inserted. In the experimental group A, the bony defect was filled with autogenous particulated bone and coverd with $Lyoplant^{(R)}$ resorbable membrane. In the experimental group B, the bony defect was filled with allograft material(Orthoblast $II^{(R)}$) containing demineralized bone matrix and covered with $Lyoplant^{(R)}$. In the control group, without any graft materials, the bony defect was covered with $Lyoplant^{(R)}$. The experimental group A and B were divided into each 9 cases and control group into 3 cases. The experimental animals were sacrificed at 3, 6 and 8 weeks after surgery and block specimens were obtained. With histologic and histomorphometric analysis, we observed the histologic changes of the cells and bone formation after H-E staining and then, measured BIC and bone density with KAPPA Image $Base^{(R)}$ system. Results: As a result of this experiment, bone formation and active remodeling process were examined in all experimental groups and the control. But, the ability of bone formation of the experimental group A was somewhat better than any other groups. Especially bone to-implant contact fraction ranged from 12.7% to 43.45% in the autogenous bone group and from 9.02% to 29.83% in DBM group, at 3 and 8 weeks. But, bone density ranged from 15.67% to 23.17% in the autogenous bone group and from 25.95% to 46.06% in DBM group at 3 and 6 weeks, respectively. Although the bone density of DBM group was better than that of autogenous bone group at 3 and 6weeks, the latter was better than the former at 8 weeks, 54.3% and 45.1%, respectively. Therefore these results showed that DBM enhanced the density of newly formed bone at least initially.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.473-476
• /
• 2004

Low-Density Parity-Check (LDPC) codes are recently emerged due to its excellent performance to use. However, the parity check matrices (H) of the previous works are not adequate for hardware implementation of encoders or decoders. This paper proposes a hybrid parity check matrix for partially parallel decoder structures, which is efficient in hardware implementation of both decoders and encoders. Using proposed methods, the encoding design can become practical while keeping the hardware complexity of partially parallel decoder structures.

• Carbon letters
• /
• v.14 no.1
• /
• pp.58-61
• /
• 2013

In this work, the effect of catalysts on the mechanical properties of carbon fibers-reinforced epoxy matrix composites cured by cationic latent thermal catalysts, i.e., N-benzylpyrazinium hexafluoroantimonate (BPH) was studied. Differential scanning calorimetry was executed for thermal characterization of the epoxy matrix system. Mechanical interfacial properties of the composites were studied by interlaminar shear strength (ILSS), critical stress intensity factor ($K_{IC}$), and specific fracture energy ($G_{IC}$). As a result, the conversion of neat epoxy matrix cured by BPH was higher than that of one cured by diaminodiphenyl methane (DDM). The ILSS, $K_{IC}$, $G_{IC}$, and impact strength of the composites cured by BPH were also superior to those of the composites cured by DDM. This was probably the consequence of the effect of the substituted benzene group of BPH catalyst, resulting in an increase in the cross-link density and structural stability of the composites studied.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.6
• /
• pp.47-52
• /
• 2003

To determine the effect of transverse open crack on the dynamic behavior of simply-supported Euler-Bernoulli beam with the moving masses, an iterative modal analysis approach is developed. The influence of depth and position of the crack in the beam, on the dynamic behavior of the simply supported beam system, have been studied by numerical method. The cracked section is represented by a local flexibility matrix, connecting two undamaged beam segments that is, the crack is modeled as a rotational spring. This flexibility matrix defines the relationship between the displacements and forces across the crack section, and is derived by applying a fundamental fracture mechanics theory. As the depth of the crack is increased, the mid-span deflection of the simply-supported beam, with the moving mass, is increased. The crack is positioned in the middle point of the pipe, and the mid-span defection of the simply-supported pipe represents maximum deflection.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.74-79
• /
• 2001

Alumina composite reinforced by chopped alumina fiber was fabricated by filter-pressing the fiber slurry followed by the infiltration of alumina slurry. The chopped fiber was coated with nickel by electroless plating method. The green samples were densified by hot-pressing. Microstructures were studied by SEM and the mechanical properties such as bending strength and fracture toughness were measured. The resulting mechanical properties were analyzed in relation with processing parameters such as preform density and resulting microstructures. The load-displacement curve of the specimen with Ni interlayer but without Ni inclusion showed brittle fracture mode due to the direct contact between matrix and fiber. The load-displacement curve of the specimen with Ni interlayer and Ni inclusion in the matrix which is introduced by high applied pressure during specimen preparation showed non-brittle fracture mode due to the fiber pull-out and dutile phases in the matrix.