• 한국수자원학회논문집
• /
• 제51권3호
• /
• pp.207-219
• /
• 2018

본 연구에서는 확률밀도함수의 서식처 적합도 지수를 사용하여 도심하천구간과 자연하천구간에서 유량점증방법론(Instream flow Incremental Methodology, IFIM)을 토대로 피라미 서식처의 생태유량을 모의하였다. 이와 같은 방법을 적용하기 위하여 본 연구에서는 PHABSIM 모형을 사용하였다. 본 연구에서는 서식처 적합도 지수(Kang, 2010)를 기초로 확률밀도함수의 매개변수를 조정하여 확률밀도함수의 서식처 적합도 지수를 개발하여 생태유량을 분석하였다. 그 결과, 도심하천구간에서는 정규분포가 자연하천구간에서는 2변수 log-pearson 분포가 Kang (2010)의 생태유량에 가장 근접하는 경향을 보였다. 확률밀도함수에 의한 서식처 적합도 지수와 하천구간별로 생태유량을 모의하여 확률론적 방법을 적용한 생태유량 산정기법을 제안하였다.

• 한국농공학회지
• /
• 제12권1호
• /
• pp.1854-1860
• /
• 1970

Results of this study on the influence of percent passing of No. 200 sieve on soil compaction are as follows; 1. The higher maximum dry density of soil is, the lower optimum moisture content is. Maximum dry density is highest value and optimum moisture content is the lowest value in twocases that percents of No. 200 sieve are 30% in soils of which percents retained on No. 10 sieve are 5% and 10% respectively. 2. Maximum dry density increases according as uniformity coefficient increase. Maximum dry density is the highest when uniformity coefficient is approximately 300 in soil of which maximum diameter is 4.76mm. 3. Maximum dry density has a tendency to become large according as value of Cu Caincrease. Correlation between maximum dry density and $Log_{10}$(CuCa) shows straight line. 4. Maximum dry density increases according as n increase and reaches the peak when n equal 0.35 in condition that the index of talbot formula n is less than 0.35 in soil of which maximum diameter is 4.76mm. 5. Maximum dry density has a tendency to increase according as value of Cg $(Cg=\frac{P_{50}^2}{P_{10}{\times}{P_{200}}$) decrease.

• 대한수학회보
• /
• 제55권3호
• /
• pp.679-698
• /
• 2018

In this paper, with optimal normalized constants, the asymptotic expansions of the distribution and density of the normalized maxima from generalized Maxwell distribution are derived. For the distributional expansion, it shows that the convergence rate of the normalized maxima to the Gumbel extreme value distribution is proportional to 1/ log n. For the density expansion, on the one hand, the main result is applied to establish the convergence rate of the density of extreme to its limit. On the other hand, the main result is applied to obtain the asymptotic expansion of the moment of maximum.

• 천문학회보
• /
• 제36권2호
• /
• pp.107.1-107.1
• /
• 2011

Density Probability Distribution Functions (PDFs) are a classic statistical way to study properties of Interstellar Medium (ISM) turbulence. In our three-dimensional MHD simulations, density PDFs of the position-position velocity (PPV) spaces are close to a log-normal distribution. the PDF widths depend on the plasma parameters such as magnetic strength and sonic Mach number. Futhermore, we compare these simulations results to Galactic molecular clouds observed by Jackson et. al (2006). By fitting of the velocity dispersion in the spectral line observation, volume density PDFs of the defined molecular clouds indicate that the sound speeds of the turbulences seem to have a few times larger than the simulation results. In order to understand the inconsistency with general characteristics of turbulence, we consider other simulations inducing the turbulent flow randomly at small driving scales. We find that the density PDF width decreases at more smaller driving scale. Finally, the simulations suggest that sources of ISM turbulence in Galactic molecular clouds can be important on small scales.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 공동학술대회 논문집
• /
• pp.323-328
• /
• 2007

We derived the dispersion curves and spectral density for several models constructed from physical property data of representative geology in Korea. Comparison between monopole and dipole sources, between physical properties, and between dispersion curves and spectral density maps have been made. The result was very helpful in sonic data acquisition as well as velocity determination.

• 한국식품저장유통학회지
• /
• 제20권5호
• /
• pp.650-658
• /
• 2013

전기장의 세기 20 kV/cm, 펄스 폭 25 ${\mu}s$에서 펄스 빈도 35 Hz(40 kJ/L), 55 Hz(70 kJ/L), 72 Hz(100 kJ/L) 및 85 Hz(130 kJ/L)로 달리하여 투입 에너지를 기준으로 사과 착즙액의 PEF 연속처리 살균 효과를 분석한 결과 일반세균수은 초기 5.3 log CFU/mL에서 130 kJ/L의 에너지로 처리하였을 때 3.0 log CFU/mL로 감소하였고 효모 및 곰팡이는 초기 4.6 log CFU/mL에서 130 kJ/L의 에너지로 처리로 < $10^1$ CFU/mL 이하로 감소하였다. 그리고 대장균군수도 초기 4.7 log CFU/mL에서 130 kJ/L의 에너지 처리로 < $10^1$ CFU/mL 이하로 감소하였다. PEF 처리에 따른 가용성 고형분, 유리당 등에는 처리 조건에 따른 유의적 차이가 없었으며(p<0.05), 총 페놀함량, DDPH 및 FRAP 값은 처리조건에 따라 부분적으로 유의적인 감소를 보였지만 $65^{\circ}C$에서의 가열처리보다는 감소량이 작았다. 전기장 세기 20.0 kV/cm, 펄스 빈도 85 Hz, 펄스 폭 25 ${\mu}s$에서의 반복처리는 미생물 살균 효과가 제한적이었고 처리회수에 따라 총 페놀함량, DPPH 및 FRAP 값을 유의적(p<0.05)으로 감소시켰다.

• Geomechanics and Engineering
• /
• 제13권1호
• /
• pp.99-117
• /
• 2017

Rock physics modeling of sandstone reservoir from gas fields of Krishna-Godavari basin represents the link between reservoir parameters and seismic properties. The rock physics diagnostic models such as contact cement, constant cement and friable sand are chosen to characterize reservoir sands of two wells in this basin. Cementation is affected by the grain sorting and cement coating on the surface of the grain. The models show that the reservoir sands in two wells under examination have varying cementation from 2 to more than 6%. Distinct and separate velocity-porosity and elastic moduli-porosity trends are observed for reservoir zones of two wells. A methodology is adopted for generation of Rock Physics Template (RPT) based on fluid replacement modeling for Raghavapuram Shale and Gollapalli Sandstones of Early Cretaceous. The ratio of P-wave velocity to S-wave velocity (Vp/Vs) and P-impedance template, generated for this above formations is able to detect shale, brine sand and gas sand with varying water saturation and porosity from wells in the Endamuru and Suryaraopeta gas fields having same shallow marine depositional characters. This RPT predicted detection of water and gas sands are matched well with conventional neutron-density cross plot analysis.

• 응용통계연구
• /
• 제28권6호
• /
• pp.1191-1208
• /
• 2015

대부분의 통계분석방법은 요약통계량에 의존하지만 그래픽적 방법을 이용하면 자료의 특성을 파악하기 쉽고 통계량만으로는 알아낼 수 없는 부분까지도 접근이 가능하다. 그래프를 통한 로지스틱회귀모형의 평가 방법으로 로그-밀도비를 통한 검토, 차원 검토, 주변모형산점도, 카이잔차산점도, CERES 그림을 알아보고 모의자료들을 통해 다양한 상황에서 그래픽적 방법들 어떠한 결과를 나타내지를 비교 검토한다.

• 한국산업융합학회 논문집
• /
• 제19권3호
• /
• pp.109-124
• /
• 2016

The objective of this paper is to find the density, stiffness, and strength of truss-wall diamond corrugation model combined with pinwheel truss inside space. The truss-wall diamond corrugation (TDC) model is defined as a unit cell coming from solid-wall diamond corrugation (SDC) model. Pinwheel truss-wall diamond corrugation (P-TDC) model is made by TDC connected with pinwheel structure inside of the space. Derived ideal solutions of P-TDC is based on truss-wall and pinwheel truss model at first. And then it is compared with Gibson-Ashby's ideal solution. To validate the ideal solutions of the P-TDC, ABAQUS software is used to predict the density, strength, and stiffness, and then each of them are compared to the ideal solution of Gibson-Ashby with a log-log scale. Applied material property is stainless steel 304 because of having cost effectiveness. Applied parameters for P-TDC are 1 thru 5 mm diameter within fixed opening width as 4mm. In conclusion, the relative Young's modulus and relative yield strength of the P-TDC unit model is reasonable matched to the ideal expectations of the Gibson-Ashby's theory. In nearby future, P-TDC model is hoped to be applied to make sandwich core structure by advanced technologies such as 3D printing skills.

• 한국산업융합학회 논문집
• /
• 제19권3호
• /
• pp.133-143
• /
• 2016

The objective in here is to find the density, stiffness, and strength of truss-wall rectangular (TWR) model which is combined with lattice truss (MLT) inside space. The TWR unit-cell model is defined as a unit cell originated from a solid-wall rectangular (SWR) model and it has an empty space inside. Thus, the empty space inside of the TWR is filled with lattice truss model defined as TWR-MLT. The ideal solutions derived of TWR-MLT are based on TWR with MLT model and it has developed by Gibson-Ashby's theory. To validate the ideal solutions of the TWR-MLT, ABAQUS software is applied to predict the density, strength, and stiffness, and then each of them are compared with the Gibson-Ashby's ideal solution as a log-log scale. Applied material property is stainless steel 304 because of cost effectiveness and easy to get around. For the analysis, SWR and TWR-MLT models are 1mm, 2mm, and 3mm truss diameter separately within a fixed 20mm opening width. In conclusion, the relative Young's modulus and relative yield strength of the TWR-MLT unit model is reasonably matched to the ideal expectations of the Gibson-Ashby's theory. In nearby future, TWR-MLT model can be verified by advanced technologies such as 3D printing skills.t.