• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.3
• /
• pp.232-239
• /
• 2010

By using the clock timing control at transmitter (TX), the crosstalk-induced jitter (CIJ) is compensated for in the 2-bit parallel data transmission through the coupled microstrip lines on printed circuit board (PCB). Compared to the authors' prior work, the delay block circuit is simplified by combining a delay block with a minimal number of stages and a 3-to-1 multiplexer. The delay block generates three clock signals with different delays corresponding to the channel delay of three different signal modes. The 3-to-1 multiplexer selects one of the three clock signals for TX timing depending on the signal mode. The TX is implemented by using a $0.18\;{\mu}m$ CMOS process. The measurement shows that the TX reduces the RX jitters by about 38 ps at the data rates from 2.6 Gbps to 3.8 Gbps. Compared to the authors' prior work, the amount of RX Jitter reduction increases from 28 ps to 38 ps by using the improved implementation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.231-242
• /
• 2001

In this paper, we present a method to improve the torque characteristic of PMSM(Permanent Magnet Synchronous Motor) and its hardware realization. It is based on the compensation of sinusoidal current delay caused by phase winding inductances. Since coordinate transformation is not used, simple hard-wired logic in the controller design is adopted and this scheme can eliminates the delay through the coordinate transformation. The delay components are varied according to rotation speeds, but this method can also make it possible to compensate those, dynamically. The control scheme has been verified by experiments on a 4-pole 3-phase PMSM, and the generated torques are increased at whole operation speed ranges.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.863-870
• /
• 2018

The traditional power control theories for the harmonic reduction methods in multilevel inverters are found to be unreliable under unbalanced load conditions. The unreliability in harmonic mitigation is caused by voltage fluctuations, non-linear loads, the use of power switches, etc. In general, the harmonics are reduced by filters. However, such devices are an expensive way to provide a smooth and fast response to secure power systems during dynamic conditions. Hence, the Decoupled Double Synchronous Reference Frame (DDSRF) theory combined with a State Delay Controller (SDC) is proposed to achieve a harmonic reduction in power systems. The DDSRF produces a sinusoidal harmonic that is the opposite of the load harmonic. Then, it injects this harmonic into power systems, which reduces the effect of harmonics. The SDC is used to reduce the delay between the compensation time for power injection and the generation of a reference signal. The proposed technique has been simulated using MATLAB and its reliability has been verified experimentally under unbalanced conditions.

• Journal of Sensor Science and Technology
• /
• v.7 no.1
• /
• pp.23-30
• /
• 1998

In this paper, we analyzed the effect of the time delay of the image sensor in the tracking loop of Electro-Optical Tracking System(EOTS). we showed that Smith predictor can greatly improve the stability and various performances of EOTS with time delay. And also, to verify the realistic validity, we executed the experiment in EOTS recently developed, and confirmed the effectiveness in EOTS.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1873-1878
• /
• 2007

Current differential relays may maloperate during magnetic inrush and over-excitation because a significant differential current is produced. To prevent maloperation, the relays adopt some harmonic components included in the differential current. The harmonic restraints may increase the security of a relay but cause the operating time delay of a relay when an internal fault occurs. Moreover, the operating time delay is more increased if a current transformer (CT) is saturated. This paper describes a current differential relaying algorithm for power transformer protection with a compensating algorithm for the secondary current of a CT. The comparative study was conducted with and without the compensating algorithm. The performance of the proposed algorithm was investigated when the measurement CT (C400) and the protection CT (C400) are used. The proposed algorithm can compensate the distorted current of a CT and thus reduce the operating time delay of the relay significantly for an internal fault with CT saturation.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.5
• /
• pp.1-7
• /
• 2011

EOTS(Electro-Optical Tracking System) provides stabilized images while tracking a moving target. The key of geo-pointing is the function that fixes EOTS's sight to a specific position(geo-point) throughout aircraft maneuvers. In this paper, a major error source for the geo-pointing is identified as the transport delay of navigation information, and an augmented Kalman filter is designed to estimate the present attitude of aircraft using delayed navigation information. Simulation results including the presented scheme shows that the error due to the information transport delay reduces under half.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.4
• /
• pp.339-345
• /
• 2007

This paper presents a design of an FPGA (Field Programmable Gate Array) -based currentcontroller. Using the nature of the high computational capability of FPGA, the digital delay due to the algorithm execution can be reduced. The control performance can be better than the conventional DSP (Digital Signal Processor)-based current controller. Moreover, this method does not need any delay compensation algorithm because the digital delay is physically diminished. Therefore, the bandwidth of the current controller can be extended by this method. The feasibility of this method is verified by several experimental results under the various conditions.

• Journal of Korea Multimedia Society
• /
• v.24 no.12
• /
• pp.1632-1640
• /
• 2021

In order to improve target tracking performance of the conventional electro-optical tracking system (EOTS) in the high speed and high maneuvering vehicle, an EOTS navigation algorithm is proposed, in which an inertial measurement unit(IMU) is included and navigation results of the vehicle are used. The proposed algorithm integrates vehicle's navigation results and the IMU and the time-delay and the scale factor errors are augmented into the integrated Kalman filter. In order to evaluate the proposed navigation algorithm, a land vehicle navigation experiments were performed a navigation grade navigation system, TALIN4000 and a tactical grade IMU, LN-200 and a equipment for roll motion were loaded on the land vehicle. The performance evaluation results show that the proposed algorithm effecting works in high maneuvering environment and for the time-delay.

• International Journal of Computer Science & Network Security
• /
• v.23 no.1
• /
• pp.96-102
• /
• 2023

In this paper, we proposed Channel Transfer Function estimation based on Delay and Doppler Profile for underwater acoustic OFDM communication system. It improved the estimation accuracy of the channel transfer function by linear time interpolation the change of Scattered Pilot (SP) insertion frequency in the time direction and the time by Delay and Doppler profile that analyzes the multipath situation of the channel investigated the performance of interpolation by simulation and report it. Previous works is inserted SP every 4 OFDM. It was effective under the environment without multipath, but it has observed that the effect of CTF compensation has been lowered in multipath channel condition. In addition to be better when inserted SP every 2 OFDM. But the amount of sending data will be decrease. Therefore, we conducted research to improve 4 OFDM with new interpolator. A computer simulation was performed as a comparison of SP inserted every 4 OFDM, SP inserted every 2 OFDM, and 4 OFDM with new interpolator. the performance of the proposed system is overwhelmingly improved, and the performance is slightly improved even 64 QAM.

• Smart Structures and Systems
• /
• v.14 no.6
• /
• pp.1173-1196
• /
• 2014

Real-time dynamic substructuring tests have been conducted on a cable-deck system. The cable is representative of a full scale cable for a cable-stayed bridge and it interacts with a deck, numerically modelled as a single-degree-of-freedom system. The purpose of exciting the inclined cable at the bottom is to identify its nonlinear dynamics and to mark the stability boundary of the semi-trivial solution. The latter physically corresponds to the point at which the cable starts to have an out-of-plane response when both input and previous response were in-plane. The numerical and the physical parts of the system interact through a transfer system, which is an actuator, and the input signal generated by the numerical model is assumed to interact instantaneously with the system. However, only an ideal system manifests a perfect correspondence between the desired signal and the applied signal. In fact, the transfer system introduces into the desired input signal a delay, which considerably affects the feedback force that, in turn, is processed to generate a new input. The effectiveness of the control algorithm is measured by using the synchronization technique, while the online adaptive forward prediction algorithm is used to compensate for the delay error, which is present in the performed tests. The response of the cable interacting with the deck has been experimentally observed, both in the presence of delay and when delay is compensated for, and it has been compared with the analytical model. The effects of the interface delay in real-time dynamic substructuring tests conducted on the cable-deck system are extensively discussed.