• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.2
• /
• pp.33-56
• /
• 2001

It is well known fact that all rocks exhibit brittle properties and time depends strain properties (creep). An understanding of the time dependent deformation behaviour of rocks is believed to be essential in the field of civil and tunnelling. The rock and concrete creep in various forms of loading conditions and physical environment are reviewed. A comparison of creep behaviour between rocks and concrete is provided, in order to bring two existing relatively independent methods of predicting creep strain closer together. It was felt that the physical process in the creep of rocks would be similar to the process in creep of concrete. Since experiments and observations have shown that non-elastic (creep) mechanical behaviour of all crystalline solids (i.e., concrete, rocks, ceramics and refractories) and single materials have a common base. Also a comparison of the results for the accepted methods of estimating creep in rocks and concrete under - multiaxial loading was attempted to extend the knowledge of deformational characteristics of these two materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3C
• /
• pp.105-113
• /
• 2009

Pressuremeter test estimates deformational properties of soil from the relationship between applied pressure and the displacement of cavity wall, and the results reflect the in-situ stress condition and the structure of soil particles. This study suggests the overall process of test and analysis for the evaluation of nonlinear degradation characteristics of shear moduli, based on the reloading curve of pressuremeter test. The method estimates the maximum shear modulus, taking into account the difference between the stress states around the probe in reloading and that of the in-situ state, and then combines the degradation characteristics of shear moduli taken from reloading curve. This procedure derives the shear moduli in overall strain range. Pressuremeter tests were carried out in various ground conditions using large calibration chamber, together with various reference tests. Shear moduli taken from pressuremeter tests were compared with bender element test and resonant column test results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2007.09a
• /
• pp.305-316
• /
• 2007

Free field ground motion during earthquake is significantly affected by the local soil conditions and it is essential for the seismic design to perform the site specific ground response analysis. So, Round Robin Test (RRT) on ground response analysis was performed for three sites in Korea. A total of 12 teams presented the results of ground response analysis with used input soil properties based on own judgement. In this paper, the results of one dimensional equivalent linear analysis presented by 11 teams were compared to evaluate the effect of input soil properties on ground response analysis. Additionally, 4 influence factors on ground response analysis, that is shear wave velocity of soil layer, nonlinear dynamic deformational characteristics, bedrock depth and bedrock velocity were studied for assumed simple soil conditions.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.57-63
• /
• 2004

The range of stresses experienced in subgrade soils and subbase materials in pavement under working stress conditions is below about 150㎪. Therefore, the deformational characteristics of soils at low confining pressures are important properties in the analysis and design of pavement system. Subgrade soils and subbase materials were collected from the actual pavement projects for testing. To evaluate the effect of confining pressure on modulus of those materials at low confining pressures, RC and FFRC tests were performed. Interestingly, the relationship between modulus of soils and confining pressure is more appropriate in linear space than in logarithm space at low confining pressure. Based on those results, new model fur evaluating the effects of confining pressure on modulus at low confining pressures was proposed.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.463-473
• /
• 2000

Reinforcement with geotextiles have been used in the foundation soil to enhance the resistance of embankments to avoid failure through excessive deformation or shear in the foundation. It is improtant to know the amount of the strain and the displacement of buried geotextiles for the verification of the reinforcement behaviour. Full scale trial constructions were performed to check the deformational characteristics of the polyester(PET) mat which was used for the embankment reinforcement. Many instrumentation equipments including surface settlement plates, profile gauges and inclinometer casings were installed to observe the behaviour of the soft ground due to the soil embankment. 60 electrical resistance strain gauges and 9 vibrating wire LVDTs were installed 세 measure the deformation of the polyester mat. Results of various tests and geotextile, waterproofing and protection from the hazard environments were introduced. The proposed instrumentation method was effective for the monitoring or the geotextile behaviour. The direct attachment of electrical resistance strain gauges on the gertextile mat was able to measure small changes of the strain of geotextiles. At the end of the 5 month monitoring, 54 of 60 (93%) strain gauges and 7 of 9 (78%) displacement transducers survived all perils of the compaction impacts and the humidity. And the tensile strain of grotextiles increased as the ground displacement became larger. Though the observed strain of mats under the 3m high embankment load was less than 1%, the magnitudes of the strain according to the mat spreading method were different from each other.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.115-121
• /
• 2010

To evaluate the engineering characteristics of aggregate base materials, cyclic triaxial, CBR and permeability tests were performed for 15 samples. The CBR values of aggregate base materials have wide range from 32 to 110(average 81) and the amount of swelling in submerged conditions has below 0.04mm. The Modulus of aggregate base materials were significantly affected by volumetric stress, linear volumetric model was best for fitting. The modulus of aggregate base materials were determined within range of 100MPa~600MPa, 80~270 and 0.1~0.6 for model coefficient $k_1$ and $k_2$ respectively. The empirical correlation model was suggested that prediction the modulus from the basic properties obtained from particle size distribution test and compaction test. The coefficient of determination of the proposed correlation model was 0.423 for model coefficient $k_1$, 0.920 for model coefficient $k_2$ and 0.872 for modulus with stress level.

• Geotechnical Engineering
• /
• v.13 no.6
• /
• pp.13-24
• /
• 1997

In Korea, granite is abundant and occupies around two-thirds of the country's ground. Bven though weathered granite residual soils are widely distributed, undisturbed sampling of this soil is extremely difficult because of the particultate structure. This difficulty has kept away the researchers from investigating !he deformational characteristics of weathered granite residual soil. Thus, a special undisturbed sampling device was developed and undisturbed samples were prepared for triaxial compression (TX), resonant column(RC), and torsional shear (75) tests. Local deformation transducer (LDT) was fabricated for internal strain measurements during TX tests. Both undisturbed samples and statically compacted samples of same density were tested by using TX with LDT, RC, and 75 test equipments. The behaviour of statically compacted specimens was almost the same as that of undisturbed samples in the strain ranges below 1 percent. The stiffness and strength decreased with increasing degree of weathering. In case of undisturbed specimens, strains at failure are widely varied from 2 percent to 11 percent, and planes of failure are irrelevant to the angle of internal friction due to the inhomogeneous nature.

• Steel and Composite Structures
• /
• v.7 no.2
• /
• pp.87-103
• /
• 2007

This paper presents some of the results from an experimental research project on the behavior of extended end-plate connections subjected to moment conducted at the Structural Laboratory of Jordan University of Science and Technology. Since the connection behavior affects the structural frame response, it must be included in the global analysis and design. In this study, the behavior of six full-scale stiffened and unstiffened cantilever connections of HEA- and IPE-sections has been investigated. Eight high strength bolts were used to connect the extended end-plate to the column flange in each case. Strain gauges were installed inside each of the top six bolts in order to obtain experimentally the actual tension force induced within each bolt. Then the connection behavior is characterized by the tension force in the bolt, extended end-plate behavior, moment-rotation relation, and beam and column strains. Some or all of these characteristics are used by many Standards; therefore, it is essential to predict the global behavior of column-beam connections by their geometrical and mechanical properties. The experimental test results are compared with two theoretical (equal distribution and linear distribution) approaches in order to assess the capabilities and accuracy of the theoretical models. A simple model of the joint is established and the essential parameters to predict its strength and deformational behavior are determined. The equal distribution method reasonably determined the tension forces in the upper two bolts while the linear distribution method underestimated them. The deformation behavior of the tested connections was characterized by separation of the column-flange from the extended end-plate almost down to the level of the upper two bolts of the lower group and below this level the two parts remained in full contact. The neutral axis of the deformed joint is reasonably assumed to pass very close to the line joining the upper two bolts of the lower group. Smooth monotonic moment-rotation relations for the all tested frames were observed.

• The Journal of the Petrological Society of Korea
• /
• v.22 no.2
• /
• pp.179-195
• /
• 2013

The study area, which is located in the southeastern part of the Jirisan province, Yeongnam massif, Korea, is mainly composed of the Precambrian Hadong southern anorthosite complex (HSAC), the Jirisan metamorphic rock complex (JMRC) and Cretaceous sedimentary rock which unconformably covers them. Lithofacies distribution of the Precambrian constituent rocks mainly shows NS and partly NE trends. This paper researched deformational phased structural characteristics of HSAC and JMRC based on the geometric and kinematic features and the forming sequence of multi-deformed rock structures, and suggests that the geological structures of this area was formed through at least three phases of ductile deformation. The first phase ($D_1$) of deformation happened due to the large-scale top-to-the SE shearing, and formed the sheath or "A"-type fold and the regional tectonic frame of NE trend in the HSAC and JMRC. The second phase ($D_2$) of deformation, like the $D_1$ deformation, regionally occurred under the EW-directed tectonic compression, and most of the NE-trending $D_1$ tectonic frame was reoriented into NS trend by the active and passive folding, and the persistent and extensive ductile shear zone (Hadong shear zone) with no less than 2.3~1.4 km width was formed along the eastern boundary of HSAC and JMRC through the mylonitization process. The third phase ($D_3$) of deformation occurred under the NS-directed tectonic compression, and partially reoriented the pre-$D_3$ structural elements into ENE or WNW direction. It means that the distribution of Precambrian lithofacies showing NE trend locally and NS trend widely in this area is closely associated with the $D_1$ and $D_2$ deformations, respectively, and the NS-trending Hadong shear zone in the eastern part of Hadong northern anorthosite complex, which is located in the north of Deokcheon River, also extends into the HSAC with continuity.

• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.803-809
• /
• 2005

The purpose of this study is to investigate the mechanical characteristics of plain and steel fiber high strength concrete under uniaxial and biaxial loading condition. A number of plain and steel fiber high strength concrete cubes having 28 days compression strength of 82.7MPa(12,000 psi) were made and tested. Four principal compression stress ratios ($\sigma_2/\sigma_1$=0.00, 050, 0.75 and 1.00), and four fiber concentrations($V_f$ =0.0, 0.5, 1.0 and $1.5\%$) were selected as major test variables. From test results, it is shown that confinement stress in minor stress direction has pronounced effect on the strength and deformational behavior. Both of the stiffness and ultimate strength of the plain and fiber high strength concrete Increased. The maximum increase of ultimate strength occurred at biaxial stress ratio of 0.5($\sigma_2/\sigma_1=0.5$) in the plain high strength concrete and the value were recorded $30\%$ over than the strength under uniaxial condition. The failure modes of plain high strength concrete under uniaxial compression were shown as splitting type of failure but steel fiber concrete specimens under biaxial condition showed shear type failure. The values of elastic modulus were also examined higher than that from ACI and CEB expression under biaxial compression condition.