• 연구논문집
• /
• s.25
• /
• pp.169-173
• /
• 1995

The high temperature deformation of mechanically alloyed Al-Ti-Si alloy (Al-9.64wt% Ti-1.56wt% Si) was investigated by performing constant load compression creep tests over the temperature range of $673^\circC$K to $723^\circC$K. From the calculation based on the modified power law creep equation for dispersion strengthened alloy, the true creep activation energy, was 176kJ/mole, the true stress exponent was 4.9. Considering the value of activation energy, stress exponent, the shape of primary creep region, it could be concluded that creep deformation in the MA Al-Ti-Si alloy is controlled by dislocation climb.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1407-1412
• /
• 2003

In MEMS devices, packaging induced stress or stress induced structure deformation become increasing concerns since it directly affects the performance of the device. In this paper, deformation behavior of MEMS gyroscope package subjected to temparature change is investigated using high-sensitivity $Moir{\acute{e}}$ interferometry. Using the real-time $Moir{\acute{e}}$ setup, fringe patterns are recorded and analyzed at several temperatures. Temperature dependent analyses of warpages and extensions/contractions of the package are presented. Linear elastic behavior is documented in the temperature region of room temperature to $125^{\circ}C$. Analysis of the package reveals that global bending occurs due to the mismatch of thermal expansion coefficient between the chip, the molding compond and the PCB.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.103-108
• /
• 2001

Wear test has been performed to evaluate the wear mechanism of Inconel alloys against ferritic stainless steels in room temperature water. By means of scanning electron microscopy (SEM), the worn surface and microstructure of subsurface layer have been examined. The wear at steady state conditions result in the formation of 5∼7${\mu}$m thick layers with fragmented microstructure. The thickness of these layers seems to depend on the ability of work hardening and deformation accommodation at the contact areas during wear. Therefore, in room temperature water, the wear rate is closely related with the wear resistance of these fragment microstructure which are generated after severe subsurface deformation.

• Journal of Magnetics
• /
• v.15 no.1
• /
• pp.32-35
• /
• 2010

The effects of Cu-addition and die-upset temperature on the texture in the die-upset Nd-lean $Nd_xFe_{93.5-(x+y)}-Cu_yGa_{0.5}B_6$ (x = 9-12, y = 0-2) alloys were investigated. The die-upset Cu-containing Nd-lean $Nd_{12}Fe_{81.5-y}-Cu_yGa_{0.5}B_6$ (y = 1, 2) alloys showed a considerable texture. Texture in the Nd-lean alloys developed through basal plane slip deformation. The Cu-addition reduced the melting point of grain boundary phase facilitating grain gliding during the die-upsetting, and providing a greater chance for the $Nd_2Fe_{14}B$ grains to meet the deformation conditions. Die-upsetting at higher temperature facilitated grain gliding and plastic deformation, thus enhancing texture.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.1
• /
• pp.157-173
• /
• 2015

In the present study, the existing equivalent stain method is improved to make up for its weaknesses. The improved inherent strain model is built considering more sophisticated three dimensional constraints which are embodied by six cubic elements attached on three sides of a core cubic element. From a few case studies, it is found that the inherent strain is mainly affected by the changes in restraints induced by changes of temperature-dependent material properties of the restraining elements. On the other hand, the degree of restraints is identified to be little influential to the inherent strain. Thus, the effect of temperature gradients over plate thickness and plate transverse direction normal to welding is reflected in the calculation of the inherent strain chart. The welding deformation can be calculated by an elastic FE analysis using the inherent strain values taken from the inherent strain chart.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1251-1252
• /
• 2006

In order to investigate 95% retained critical current of Bi-2223/Ag tapes under various stress-strain conditions, load cell attached tension and bending apparatus was used. The critical current of stress-strained tape was degraded below 95% retained critical current when tension and bending was simultaneously applied together. But only one of this tension or bending did not degrade the tape below 95% retained critical current. Deformation temperature was important to maintain the 95% retained Ic of Bi-2223/Ag tapes after bending or tension deformation because mechanical strength of tapes can be changed drastically between room temperature and 77 K.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.4
• /
• pp.121-128
• /
• 1996

In order to examine spindle deformation characteristics that affects the performance of dynmic cutting acuracy due to tool weight variation in a experimental spindle. thermal deformation value of operrative spindle by the axial displacement and the radial run out was measured according to the rise of spindle temperature through the laps of operation time and the change of rotational speed under the tool weight variation. A qualitative summary is as follows ; 1) The results show that the tool weight affcets the spindle temperature variation in a experimental spindle. 2) Radial run out and axial displacement was measured according to the rise of the spindle temperature and the performance of dynamic cutting accuracy was affected by the tool weight variation. 3) Axial displacement is 1.3 times larger than the radial run out in a experimental spindle conditions. 4) Axial displacement is continuously elongated when the tool weight is repeatly exchanged since the spindle themal deformaion, however, when the same tool weight is used. the displacement is still constant.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.10-19
• /
• 1996

Grinding temperature and thermal deformation(dimensional error) are studied theoretically and experimentally. The propose of this research is clarified loading phenomena and residual stress In order to guide nozzle's efficiency. The main results to be obtained are as follows ; 1) When grinding condition Is high efficient grinding, FEM program is developed about grinding heat and dimensional error. 2) Thermal deformation depend on temperature distribution is in good agreement with experimental results in case of little grinding energy flux but is comparatively in good agreement with in case of large (3.5$\times$10$^{6}$ J/m). 3) In terms of high efficient grinding at field(table speed 4m/min), grinding fluid (dilution 5/100) obtained a good workpiece quality and decreased a grinding temperature. 4) A surface roughness, dimensional error, residual stress and loading phenomena with guide nozzle are decreased and these results obtained a good workpiece quality.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.187-194
• /
• 2001

The objective of this study is to develop a model for the grinding process for predicting the temperature, thermal stress and thermal deformation. The thermal load during grinding is modeled as uniformly distributed, 2D heat source moving across the surface of elastic half space, which is insulated or subjected to convective cooling. That non-dimensional temperature distribution, non-dimensional longitudinal stress distribution and non-dimensional thermal deformation distribution are calculated with non-dimensional heat source half width and non-dimensional heat transfer coefficient. Finite element models are developed to simulate moving heat source, which is modeled as uniformly or triangularly distributed, the FEM simulation is compared with numerical solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.448-451
• /
• 2005

An aspheric mirror, which requires less than $\lambda/2\;(\lambda=632.8nm)$ of form error for the $\phi$ 200mm reference curved surface, has been manufactured with an ultra-precision turning machine. We have known through several tests that the deformation patterns of the reflecting surface is related with bolting positions. In this paper the effect of main factors on deformation of a reflector is studied with a FE code. The considered factors are angular velocity, natural frequencies for a mirror, temperature increment during machining. The obtained test results are similar to the deformation shape due to the assumed temperature increment.