• Magazine of the Korean Society of Agricultural Engineers
• /
• v.38 no.3
• /
• pp.70-81
• /
• 1996

Solutions of geotechnical engineering problems require predictions of deformation and stresses during various stages of loading. Powerful numerical methods are available to make such predictions even for complicated problems. To get accurate results, realistic stress-strain relationships of soils are dependent on a number of factors such as soil type, density, stress level and stress path. Attempts are continuously being made to develope analytical models for soils incorporating all such factors. Isotropic compression-expansion test and a series of drained conventional triaxial tests with several stress path for Baekma river sand were performed to investigate stress-strain and volume change characteristics of Lade's single work hardening model dependant on the stress path. In order to predicted of stress-strain and volumetric strain behavior were determined the values of parameters for the mode by the computer program based on the regression analysis. Predicted stress-strain behavior of triaxial compression tests and optional stress path tests for increasing confining pressure with parameters obtained conventional triaxial compression tests agreed with several test results but the prediction results for decreasing confining pressure reduced triaxial compression tests make a little difference with test results.

• Transactions of Materials Processing
• /
• v.17 no.6
• /
• pp.420-428
• /
• 2008

The effect of loading path changes on the strain and mechanical properties of a commercial pure aluminum was studied using flat rolling and groove rolling. Material during flat rolling undergoes a continuous monotonic compressive loading, while one during groove rolling experiences a series of cross compressive loading. Four-pass flat rolling and groove rolling experiment are designed such that the aluminum undergoes the same amount of the strain at each pass. The rolling experiment was performed at room temperatures. Specimens for tensile test are fabricated from the plate and bar rolled. In addition, the strain distribution for the plate and bar cold rolled specimens is also calculated by finite element method. The results reveal that differences of loading path attributed by monotonic loading(flat rolling) and cross loading(groove rolling) significantly influence the mechanical properties such as yield stress, ultimate tensile stress, strain hardening and elongation. It is clear that the different loading path can give raise to change the deformation history, although it is deformed with same amount of strain for same material.

• Computers and Concrete
• /
• v.29 no.5
• /
• pp.303-321
• /
• 2022

The current design equations for predicting the torsional capacity of RC members underestimate the torsional strength of under-reinforced members and overestimate the torsional strength of over-reinforced members. This is because the design equations consider only the yield strength of torsional reinforcement and the cross-sectional properties of members in determining the torsional capacity. This paper presents an analytical model to predict the thickness of shear flow path in RC beams subjected to pure torsion. The analytical model assumes that torsional reinforcement resists torsional moment with a sufficient deformation capacity until concrete fails by crushing. The ACI 318 code is modified by applying analytical results from the proposed model such as the average stress of torsional reinforcement and the effective gross area enclosed by the shear flow path. Comparison of the calculated and observed torsional strengths of existing 129 test beams showed good agreement. Two design variables related to the compressive strength of concrete in the proposed model are approximated for design application. The accuracy of the ACI 318 code for the over-reinforced test beams improved somewhat with the use of the approximations for the average stresses of reinforcements and the effective gross area enclosed by the shear flow path.

• Structural Engineering and Mechanics
• /
• v.62 no.5
• /
• pp.619-629
• /
• 2017

This paper focuses on the study of complete dynamic modeling and maximum dynamic load carrying capacity computation of N-flexible links and N-flexible joints mobile manipulator undergoing large deformation. Nonlinear dynamic analysis relies on the Timoshenko theory of beams. In order to model the system completely and precisely, structural and joint flexibility, nonlinear strain-displacement relationship, payload, and non-holonomic constraints will be considered to. A finite element solution method based on mixed method is applied to model the shear deformation. This procedure is considerably more involved than displacement based element and shear deformation can be readily included without inducing the shear locking in the element. Another goal of this paper is to present a computational procedure for determination of the maximum dynamic load of geometrically nonlinear manipulators with structural and joint flexibility. An effective measure named as Moment-Height Stability (MHS) measure is applied to consider the dynamic stability of a wheeled mobile manipulator. Simulations are performed for mobile base manipulator with two flexible links and joints. The results represent that dynamic stability constraint is sensitive when calculating the maximum carrying load. Furthermore, by changing the trajectory of end effector, allowable load also changes. The effect of torsional spring parameter on the joint deformation is investigated in a parametric sensitivity study. The findings show that, by the increase of torsional stiffness, the behavior of system approaches to a system with rigid joints and allowable load of robot is also enhanced. A comparison is also made between the results obtained from small and large deformation models. Fluctuation range in obtained figures for angular displacement of links and end effector path is bigger for large deformation model. Experimental results are also provided to validate the theoretical model and these have good agreement with the simulated results.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.130-133
• /
• 2008

The formability of DP steels can be affected by not only initial texture but also deformation texture evolved during plastic deformation. To investigate the evolution of deformation texture during deep drawing, deep drawing process for DP steels was carried out experimentally. A rate sensitive polycrystal model was used to predict texture evolution during deep drawing process. In order to evaluate the strain path during deep drawing, a steady state was assumed in the flange part of deep drawn cup. A rate sensitive polycrystal model successfully predicted the texture development in DP steels during deep drawing process. It was found that the final stable orientations were strongly dependent on the initial location in the blank.

• Structural Engineering and Mechanics
• /
• v.33 no.1
• /
• pp.67-77
• /
• 2009

The soil response calculation is described, by which, threw the fictive path of stress, the stress-deformation diagrams are determined, considering the nonlinear soil behavior. The calculation are lead incrementally, by which is shown that in the presented soil model (modified Cam Clay), considering the influence of overconsolidated soil pressure OCR, the number of calculation steps may, but not necessarily, have a sufficient influence on the value of failure load and definite soil deformation. The simplicity and the practicalness of the procedure, the enables modeling the complex relations in soil.

• Journal of Welding and Joining
• /
• v.25 no.5
• /
• pp.72-77
• /
• 2007

Prediction and control of the thermal distortion is particularly important for the design and manufacture of welded thin metal structure. In this study, numerical computations are performed to analyze effect of structure section shape and weld line location on distortion. In addition, this study aims to develop a thermal elasto-plastic simulation using finite element method to predict distortion, with particular emphasis on bending deformation generated in outline welding of a thin box structure. From the numerical analysis, it was revealed that the section shape and weld line location play an important role on the welding distortion. Among 3 types of section shape design proposed in this study, the least deformation remained in the two path welded structure.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.85-98
• /
• 2001

Cone penetration was analyzed by arbitrary Lagangian-Eulerian(ALE) method. In order to simulate full penetration, steady state analyses were performed using ABAQUS/Explicit, which models upward flow of soil layers. In the analysis of homogeneous layer it was found that the paths and the strain of soil particles were consistent with the result of the strain path method and that the ultimate resistance were reasonably evaluated. The cone penetration through different soil layers was also analyzed and that showed the transfer of cone resistance. The steady state ALE analysis could perform full penetration through the layered soils.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.1
• /
• pp.160-170
• /
• 2008

Shape morphing is the process of transforming a source shape, through intermediate shapes, into a target shape. Two main problems to be considered in three dimensional shape morphing are vertex correspondence and path interpolation. In this paper, an approach which uses the linear interpolation of the Laplacian coordinates of the source and target meshes is introduced for the determination of more plausible path when two topologically identical shapes are morphed. When two shapes to be morphed are different in shape and topology, a new method which combines shape deformation theory based on Laplacian coordinate and mean value coordinate with distance field theory is proposed for the efficient treatment of vertex correspondence and path interpolation problems. The validity and effectiveness of the suggested method was demonstrated by using it to morph large and complex polygon models including male and female whole body models.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.06a
• /
• pp.156-163
• /
• 1998

During an actual forming operation, a material may undergo considrably large changes in strain path, and these changes can significantly alter the forming limits. So, in this study, modified forming limit curves(FLCs) in complex strain path are determined with specially designed jig to give test specimens with desired prestrains in uniaxial or biaxial deformation mode. In another part of present study, theoretical prediction of FLCs is attempted with MK's theory and Hosford's yield criterion to give forming limit curves in positive minor strain region and with Hill's local necking theory in negative minor strain region. Comparison of these theoretical results with experimental ones will be mentioned for both linear and complex strain path.