• Korean Journal of Optics and Photonics
• /
• v.24 no.6
• /
• pp.324-330
• /
• 2013

Phase-measuring deflectometry is a full-field gradient measuring technique that lends itself very well to testing specular optical surfaces. We have measured deformation of a large specular surface by deflectometry. In this work, we have used a Fourier-transform method to get the phase from a measured deformed fringe pattern, and we have used least squares method to obtain the height information of the specular surface from the calculated slope. Experimentally, we have confirmed that deflectometry can be used for deformation measurement of a specular surface like that of a wafer.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.256-261
• /
• 2016

In this paper, Shape optimal design for a chair with 4 legs and 2 stretchers consisting of stainless steel was conducted. The shape was transformed by identifying stress and deformation for the part of leg and stretcher. In addition, load condition and mesh was designed using Hypermesh. The stress analysis was carried out using CSD_Elast that is one of EDISON program. In seat test, Maximum equivalent stress was showed at the contact part between seat and legs. As a result, a leg cross-section with rectangular and arch was designed. And optimal height of stretcher was found to reduce a deformation. Also, maximum deformation was reduced by designing a stretcher with ellipse cross-section. So, Optimal chair having 4 legs with rectangular cross section and 2 stretchers with ellipse cross section was shown to satisfy the safety ratio.

• Tunnel and Underground Space
• /
• v.6 no.1
• /
• pp.10-18
• /
• 1996

Arched openings are generally excavated in underground construction works. Since stress distribution around openings depends on geological structure in rock mass, any shape of arched openings fully conformed with in-situ stress condition should be recommended to maintain mechanical safety of structures. Shape of arched openings is specified by both roof curvature and height-width ratio, and especially this report presents deformation behaviors related with roof curvature. Scale model tests and numerical studies of various shaped openings are conducted, where rectangular opening shows the greatest convergence. Through the anlayses of various arched opengings, as radius of roof curvature is increased, roof lowering and sidewall closure are remarkably increased, whereas floor heaving is increased little by little. By the way, it is useful that displacements of openings are roughly estimated in the stage of preliminary investigation. To find out elastic displacements of arched openings with any roof curvature, regressional formula and charts by least square method are represented. In addition elastoplastic deformation behavoirs of arched openings concerning associated adn non-associated flow rule are discussed.

• Advances in nano research
• /
• v.15 no.2
• /
• pp.165-174
• /
• 2023

The study investigated the effect of geometric structures of nano-patterned surfaces, such as peak sharpness, height, width, aspect ratio, and spacing, on mechano-bactericidal properties. Here, in silico models were developed to explain surface interactions with Escherichia coli. Numerical solutions were performed based on the finite element method and verified by the artificial neural network method. An E. coli cell adhered to the nano surface formed elastic and creep deformation models, and the cells' maximum deformation, maximum stress, and maximum strain were calculated. The results determined that the increase in peak sharpness, aspect ratio, and spacing values increased the maximum deformation, maximum stress, and maximum strain on E. coli cell. In addition, the results showed that FEM and ANN methods were in good agreement with each other. This study proved that the geometrical structures of nano-patterned surfaces have an important role in the mechano-bactericidal effect.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.6
• /
• pp.653-660
• /
• 2015

Technologies for reducing construction duration are key factors in nuclear power plant construction projects, as a reduction in construction duration at the construction phase leads to a reduction in construction cost and an increase in profits through the early operation of the nuclear power plant. To analyze the constructability of the height of single-layer placement of formwork for the Reactor Containment Building (RCB) exterior wall through lateral pressure according to the height of concrete placement, the deformation criteria for formwork, and a new form design, 'MIDAS GEN (hereinafter referred to as MIDAS)' is used in this study. The cost and workload of formwork are derived according to the unit of height of the RCB exterior wall. Based on the result, it was found that the higher the RCB exterior wall, the higher the material cost, and the less the construction duration and the less the total number of formwork layers. Based on this result, it is believed that the material cost and the construction duration can be appropriately determined according to the formwork height.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.29-33
• /
• 2016

Production machines have been more important, due to quality level of vehicle motor core is getting higher. That is why, to improve assembly fit of tooling and to be emphasized how much moving down caused of deterioration of high speed press, it is also getting more important parts as solution of problems. To analyze how much move based on condition of movement as tooling and high speed press, and to measure how much impact to embossing height caused of changing movement down. As the result of investigation, in case of material thickness 0.5mm, there is highest pull and force power when emboss height is 0.45mm. If emboss height is less than 0.45mm, pull and force power is getting lower, if emboss height is higher than 0.45mm, it is impossible to make it forming caused of changed press movement, also it has been piercing.

• Journal of the Korean Society of Safety
• /
• v.12 no.3
• /
• pp.52-59
• /
• 1997

Hill's anisotropy theory and isotropy theory under the deformed profile assumed two separate cases(that is circular and ellipitical) are applied to predict the plastic deformation characteristics of bulge, the strain and polar height under instability condition, using thin square diaphragms of stainless steel, mild steel, brass, copper and aluminum. In this study it was found that the pressure-polar height curves, and the polar height-the polar radius of curvature curve, under anisotropy theory and isotropy theory, assuming a circle profile, agree well with the experimental results, and the equivalent strains of the instability condition under anisotropy theory are better good agreement with the experimental results than those of the instability condition under isotropy theory. Beside, FLCo(plane Strain Intercept) obtained by Bethlehem FLC method and standard FLC method (modified) agree well with the experimental result.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.121-129
• /
• 1993

Plane strain punch stretching test (PSST) was developed to evaluate stamping formability of sheet materials. In this test, the rectangular specimen of sheet material is uniformly stretched up to fracture by raising a specially designed punch to certainly assure plane strain stretching deformation along the longitudinal direction of the specimen. The stamping formability was evaluated by limit punch height(LPH) in plane strain punch stretching test compared to limit dome height(LDH) in hemispherical punch stretching test. LPH-value in PSST well ranks the stamping formability of various material and correlates with press performance. Moreover by using ultrasonic thickness gauge the plane strain intercept-limit plane strain(FLCo)-in forming limit curve can be accurately determined from thickness measurement around the fracture area. The FLCo derived from thickness measurement well correlates with the results from circle grid analysis for the deformed circle grid marked on the surface of the specimen.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1690-1692
• /
• 2000

The principle of crimping connection is to produce a compressive connection force between terminal and cores(wire conductor). Compressive connection force is produced by pushing each other on that stress(crimping force) of barrel by restored elastic strain after plastic deformation and the expansion force of cores' elastic stress. And resistance and tension force between terminal and cores are determined according to the condition of compressive connection force. In this study, we've found out that the adaptive height which has maximum tensile force by measuring a tensile force with a height of terminal.

• Transactions of Materials Processing
• /
• v.3 no.3
• /
• pp.291-301
• /
• 1994

In the simultaneous forward-backward extrusion the effects of some process variables including area reduction, stroke advance, materials(Al 2024 and commercial pure copper) on the extrusion load, plastic flow and height ratio of upper to lower extruded parts are experimentally investigated and analyzed. Grid-marking technique is employed to visualize the plastic flow. The influence of using split and original specimen on the extrusion load and height ratio is evaluated by experiments. Experimental results show that the plastic flow if oriented to the part of lower area reduction in the begining but it is usually variated during the overall process. The configurations of plastic deformation and plastic flow are dependent on the working materials and the lubricational conditions.