• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• 소성∙가공
• /
• 제7권1호
• /
• pp.36-48
• /
• 1998

In order to analyze the stretch flange forming characteristics of tailored blanks. laser welded blanks of different thickness and strength combinations were prepared and hole expansion tests were done. The stretch flange formability of laser welded blanks was reduced as increasing the deformation restraining force($strength{\times}thickness$) ratio between two welded sheets. Simulation of stretch forming mode deformation and comparson with experimental results showed that the stretch flange formabili-ty was influenced not only by the difference of the deformation restraining forces between two base sheets but also by the difference of the deformation restraining forces between base sheet and weld. Therefore the stretch flange formability was reduced more rapidly than tensile elongation as increas-ing the deformation restraining force ration. It was also found that simulation of stretch flange forming was more accurate when material properties of weld was given.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.211-216
• /
• 2016

Al alloys are useful materials having high specific strength and are used in machining of parts having thin-walled structures for weight reduction in aircraft, automobiles, and portable devices. In machining of thin-walled structures, it is difficult to maintain dimensional accuracy because machining deformation occurs because of cutting forces and heat in the cutting zone. Thus, cutting conditions and methods need to be investigated and cutting signals need to be analyzed to diagnose and minimize machining deformation and thereby enhance machining quality. In this study, an investigation on cutting conditions to minimize machining deformation and an analysis on characteristics of cutting signals when machining deformation occurs are conducted. Cutting signals for the process are acquired by using an accelerometer and acoustic emission (AE) sensor. Signal characteristics according to the cutting conditions and the relation between machining deformation and cutting signals are analyzed.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.51-56
• /
• 2002

In this paper, the stress and deformation characteristics of the high pressure hose that have the hose components such as rubber, braid and steel( sleeve and nipple) during the manufacturing process, and analyzed using the [mite element method The swaging process is modeled with a contact problem in identical conditions of real circumstances, and the properties of hose materials based on the experimental data are used in this analysis. Also, to understand the effect of the nipple protrusions on the deformation characteristics of a power steering hose among the steel materials shape of the existing model, and changed the steel materials shape partially, and compared with the existing model.

• 대한조선학회논문집
• /
• 제38권4호
• /
• pp.66-74
• /
• 2001

선체 외판 제작을 위한 곡가공은 조선에 있어서 필수적인 공정이다. 프레스를 이용한 냉간가공과 가스토치를 이용한 열간가공이 주를 이루는데, 특히 숙련된 기능공의 작업 경험에 전적으로 의존하는 열간가공 공정에 대한 자동화 요구가 증대되어 국내외적으로 많은 연구가 진행되고 있다. 본 연구는 향후 삼각가열에 대한 효율적인 변형해석 기법을 개발하기 위한 기초 연구로서 삼각가열에 의한 판의 변형특성과 그 주요인자를 파악하고자 하였다. 실제 조선소에서 현장조건 그대로 Jang 등(2001)이 실시한 일련의 삼각가열 실험 결과를 토대로 열탄소성 해석을 위한 수치해석 모델을 개발하고 상용 구조해석 프로그램인 ANSYS를 이용하여 삼각가열에 의한 판의 변형을 시뮬레이션하였다. 또한, 총 투입 열량이 같은 경우 선상가열과 삼각가열에 의한 변형 양상을 비교하여 각 가열법에 따른 변형 특성을 보다 명확히 하였다. 마지막으로, 단위부피당 투입열량에 따른 각 변형 성분의 변화 특성을 살펴보았다.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.59-64
• /
• 1998

This paper presents the deformation characteristics of cam ring in a balanced type vane pump. Cam ring is operated in the high-pressure condition. Therefore the local deformation of cam ring affects the characteristics of compression, vane motion and noise and vibration. We analyzed the deformation of cam ring for the three types by using the finite element method. The deformed shape of cam ring and the effects of deformation on the compression are presented. As a result of analysis, we know that the right hole of the cam ring has advantage for reducing the pressure overshoot.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.61-64
• /
• 2004

The strength characteristics as well as deformation behaviors of honeycomb sandwich composite (HSC) structures were investigated under bending in consideration of various failure modes such as skin layer yielding, interface-delamination, core shear deformation and local buckling. Deformation behaviors of honeycomb sandwich plates were observed with various types of aluminum honeycomb core and skin layer. Their finite-element analysis simulation with a real model of honeycomb core was performed to analyze stresses and deformation behaviors of honeycomb sandwich plates. Its results were very comparable to the experimental ones. Consequently, the increase in skin layer thickness and in cell size of honeycomb core had dominant effects on the strength and deformation behaviors of honeycomb sandwich composites.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.195-198
• /
• 2000

It can be acquired the high effective productivity through of high speed, precision of machine tools, and then, machine tools will be got a competitive power. Industrially advanced countries already developed that the high speed feed is 60m/min using the high speed ball screw. Also, a lot of problems have happened the feed drive system. It is necessary to study about the characteristics of thermal deformation played a more critical role than static stiffness and dynamic rigidity in controlling the level of machining accuracy. In spite of the improving the thermal deformation characteristics of machine tools at the design stage, there are always some residual errors that have to be compensated for during machining. In this study, thermal deformation error automated compensation device with multiple linear regression is proposed that thermal deformation error can be eliminated at the machining stage. The developed device has been practically applied to the feed drive unit.

• 터널과지하공간
• /
• 제4권3호
• /
• pp.274-286
• /
• 1994

Direct shear tests were on ducted in a laboratory setting in order to investigate the shear strength and deformation behavior of rock joints. Also, the characteristics of acoustic emissions (AE) during shearing of rock joints were studied. The artificial rock joints were created by splitting the intact blocks of Hwangdeung granites and Iksan marbles. Joint roughness profiles were measured by a profile gage and then digitized by Image analyzer. Roughness profile indices(Rp) of the joints were calculated with these digitized data. Peak shear strength, residual shear strength, shear stiffness and maximum acoustic emission(AE) rate were investigated with joint roughness. The peak shear strenght, the residual shear strength and the shear stiffness were increased as roughness popfile index or normal stress increased in the shear tests of granites. In the tests of marble samples, the shear deformation characteristics were not directly affected by joint roughness. As the result of two directional shear tests, the shear characteristics were varied with shear direction. AE count rates were measured during the shear deformation and the AE signals in several stages of the deformation were analyzed in a frequency domain. The AE rate peaks coincided with the stress drops during the shear deformation of joint. The dominant frequencies of the AE signals were in the vicinity of 100 kHz fo rgranite sample and 900 kHz for marble samples. The distribution of amplitude was dispersed with increasing normal stress.

• Journal of Welding and Joining
• /
• 제28권1호
• /
• pp.92-99
• /
• 2010

For the last couple of decades many studies have been carried out to find out solutions to improve the effectiveness and productivity of the plate forming process. The practical way for the automation of the plate forming process has not been, however, developed yet. Since the characteristics of heating machines may be different form each other, it is necessary to investigate the thermal deformation characteristics of the heating machine to be used in the automation system. And their characteristics may be updated as new information about thermal deformation by heating is accumulated. In this paper, data base system has been constructed based on the results of experiments and numerical analyses, which will be used in deriving the deformation estimation formula. The computer code which can automatically derive the deformation estimation formula has been also developed. This paper also illustrates how the formula is updated as experimental data are added. From the present findings, it can be said that the automatic deriving procedure may be important in the automated plate forming system since the heating line information to be generated must be directly influenced by the deformation estimation formula.