• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.3
• /
• pp.379-386
• /
• 2016

In this paper, phase noise analysis result for 2.4 GHz PLL(phase locked loop) using SPD(sample phase detector) is proposed. It can be used for high performance frequency synthesizer's LO(local oscillator) to extend output frequency range or for LO of offset PLL to reduce a division rate or for clock signal of DDS(direct digital synthesizer). Before manufacturing, theoretical estimation of PLL's phase noise performance should be performed. In order to calculate phase noise of PLL using SPD, Leeson model is used for modeling phase noise of VCO(voltage controlled oscillator) and OCXO(ovened crystal oscillator). After theoretically analyzing phase noise of PLL, optimized loop filter bandwidth was determined. And then, phase noise of designed loop filter was calculated to find suitable OP-Amp. Also, the calculated result of phase noise was compared with the measured one. The measured phase noise of PLL was -130 dBc/Hz @ 10 kHz.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.11
• /
• pp.868-875
• /
• 2014

The requirement of acoustic material which is used in underwater environment more increases. The material is used to reduce acoustic signature and radiate noise for underwater vehicle. Underwater acoustic material was made by viscoelastic material such as rubber and polyurethane etc. The mechanical and acoustic characteristics of these material change with hydrostatic pressure. In order to improve an acoustic performance according to hydrostatic pressure, several kinds of scatterers were added to viscoelastic material. In this paper, acoustic modelling and analysis techniques of underwater acoustic material with hydrostatic pressure were introduced and proposed. The specimens for pulse tube test were made and echo reductions were calculated and measured with hydrostatic pressure. Also the characteristics of echo reduction of the specimens with hydrostatic pressure were obtained and discussed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.392-400
• /
• 2019

This paper provides a fin actuation system of missile based on electromagnetic-spring mechanism to miniaturize the system and lower the cost. Compared with proportional electro-mechanical actuators, the output of Electromagnetic-Spring Actuators(EMSA) has two or three discrete states, but the mechanical configuration of EMSA is simple since it does not need power trains like gears. The simple mechanism of EMSA makes it easy to build small size, low cost, and relatively high torque actuators. However, fast response time is required to improve the dynamic performance and accuracy of missiles since bang-off-bang operation of EMSA affects the flight performance of missile. In this paper the development of EMSA including parameter optimization and mathematical modeling is described. The simulation results using Simulink and experimental test results of prototype EMSAs are presented.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.857-864
• /
• 2018

This paper describes about the circuit design and test of the electronic Arm Fire Device. Electronic arm fire device consists of igniter, circuit and housing case and it operates without the actuator such as torque motor or solenoid. A high-voltage DC-DC converter was used to generate the voltage for initiating the LEEFI(Low Energy Exploding Foil Initiator). The MEMS switch was used to detect the acceleration that occurs when missile is launched, and the circuit was designed considering the size, performance, and specification of the electronic devices. The performance test was conducted to verify the designed circuit and we confirmed that it operates well.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.11
• /
• pp.5481-5495
• /
• 2018

Single pixel imaging technology has developed for years, however the video acquisition on the single pixel camera is not a well-studied problem in computer vision. This work proposes a new scheme for single pixel camera to acquire video data and a new regularization for robust signal recovery algorithm. The method establishes a single pixel video compressive sensing scheme to reconstruct the video clips in spatial domain by recovering the difference of the consecutive frames. Different from traditional data acquisition method works in transform domain, the proposed scheme reconstructs the video frames directly in spatial domain. At the same time, a new regularization called spatial cluster is introduced to improve the performance of signal reconstruction. The regularization derives from the observation that the nonzero coefficients often tend to be clustered in the difference of the consecutive video frames. We implement an experiment platform to illustrate the effectiveness of the proposed algorithm. Numerous experiments show the well performance of video acquisition and frame reconstruction on single pixel camera.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.4
• /
• pp.412-424
• /
• 2022

Since traditional derivative-based optimization for noisy simulation shows bad performance, evolutionary algorithms are considered as substitutes. Especially in case when outputs are binary, more simulation trials are needed to get near-optimal solution since the outputs are discrete and have high and heterogeneous variance. In this paper, we propose a genetic algorithm called SARAGA which adopts dynamic resampling and fitness approximation using surrogate. SARAGA reduces unnecessary numbers of expensive simulations to estimate success probabilities estimated from binary simulation outputs. SARAGA allocates number of samples to each solution dynamically and sometimes approximates the fitness without additional expensive experiments. Experimental results show that this novel approach is effective and proper hyper parameter choice of surrogate and resampling can improve the performance of algorithm.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.26 no.3
• /
• pp.205-213
• /
• 2023

An optimal design of a simple beam-shaped flexure hinge mount supporting an optical mirror is presented. An optical mirror assembly is an opto-mechanically coupled system as the optical and mechanical behaviors interact. This side-supporting mount is flexible in the radial direction and rigid for the remaining degrees of freedom to support the mirror without transferring thermal load. Through thermo-elastic, optical and eigenvalue analysis, opto-mechanical performance was predicted to establish the objective functions for optimization. The key design parameters for this flexure are the thickness and length. To find the optimal values of design parameters, response surface analysis was performed using the design of experiment based on nested FCD. Optimal design candidates were derived from the response surface analysis, and the optimal design shape was confirmed through Opto-mechanical performance validation analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.44-53
• /
• 2022

The depressurization rate in a thrust variable solid rocket motor is the major factor that has the greatest influence on the thrust termination performance. In this study, the depressurization rates range of model solid rocket motor was identified and major factors affecting the depressurization rate were found. It is important for actual system design to understand the depressurization rate of the system that can satisfy the target performance as well as the extinguishing characteristics of the solid propellant. The methodology for obtaining the depressurization rate model in this study is considered to be applicable to the optimal design of the thrust terminable propulsion system.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.31 no.3
• /
• pp.133-141
• /
• 2023

In the recent context of the Fourth Industrial Revolution, there is growing interest in digital transformation and smart factory as a focal point. But, the Aerospace and Defense (A&D) sector has seen limited research on digital transformation, primarily concentrating on digitally-driven areas. The study validates hypotheses pertaining to the factors that facilitate successful digital transformation within the A&D sector and the influence of digital leadership and dynamic capabilities, employing statistical tools like SPSS and AMOS. The comprehensive analysis reveals that, similar to manufacturing industries, digital leadership in A&D companies exerts an influence on successful digital transformation through dynamic capabilities. Furthermore, digital transformation within the A&D sector has a positive impact on firm performance. This paper offers empirical insights into digital transformation within the A&D sector, shedding light on how successful digital transformation can be achieved within the domestic A&D industry.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.456-461
• /
• 1993

In this paper, a new guidance law for a short-range air-to-air missile with constant thrust is presented. It is essentially based on the concept of proportional navigation. First, the theoretical guidance law is derived. Then, we show the technique for practical implementation of the guidance law. By a computer simulation, it is shown that the new guidance law gives better performance than the conventional proportional navigation.