• 소성∙가공
• /
• 제18권1호
• /
• pp.52-58
• /
• 2009

Generally, a vertical rolling process is used to achieve extensive width reduction in hot strip mill. However, it is impossible to avoid the defects such as dog-bone and edge-seam defect. The sizing press process has been developed in response to the defects mentioned above. Especially, this study is carried out to investigate the deformation of slab by two-step sizing press. The deformation behavior of slab in the sizing press process is more favorable than that in conventional vertical rolling edger. The FE-simulation is applied to predict the deformation behavior of the slab. In this paper, the several causes of the asymmetrical deformation are mentioned for the purpose of understanding of the anvil shape. Load, dog-bone and edge-seam defect are discussed in width sizing process considering the anvil shape. And to reduce the problems generated at rougher mill just after sizing press, these are studied in this paper. The deformation behavior of slabs and optimum anvil shape are obtained by rigid-plastic finite element analyses and neural network.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.437-438
• /
• 2006

Generally, the vertical roll process is used to achieve extensive width reduction in hot strip mill. However, it is difficult to avoid the defects such as dog-bone and seam-defect. The sizing press has been developed in response to the defects mentioned above. Especially, this study is carried out to investigate the deformation of slab by two-step sizing press. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger. The objective of this study is to determine the optimal anvil shape parameters in the sizing press with two-step die from the viewpoint of edge-seam length. In general, the edge-seam defect occurs parallel to the rolling direction at both edges in horizontal rolling process after sizing press. The optimal combination of the parameters is determined by FE-simulation and Artificial Neural Network (ANN). The slab deformation in sizing press with convex anvil is analyzed by FE-simulation. The most suitable profile of the anvil is also discussed fur the improvement of trimming loss because of the side seam defect by FE-simulation and ANN.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.321-327
• /
• 2007

위상잠금 적외선 열화상기법은 넓은 면적을 동시에 검사할 수 있으며, 결함부와 건전부 사이의 위상 차로부터 결함의 유무를 판단할 수 있다. 지금까지 결함의 크기는 검사자의 주관적 판단으로 평가되어 왔으며, 재현성과 정확성이 부족하였다. 본 논문에서는 결함의 크기와 위치 평가에 있어 정확성과 재현성을 개선하기 위해서 전단위상기법을 제안하였다. 시험에서는 인공결함을 갖는 시험편으로 제안된 기법을 검증하였으며, 결함평가에 영향을 주는 인자를 추출하여 그 영향을 분석하였다.

• 대한기계학회논문집A
• /
• 제20권8호
• /
• pp.2458-2467
• /
• 1996

The rigid-plastic finite element analysis was performed for analysis of ofhot forging and cold sizing of a bevel gear. Two dimensional analysis was carried out to investigate the defect occurrence on vertical symmetric planes during hot forging and three dimensional analysis was to understand the filling behavior on horizontal planes during cold sizing. The involute curve of a tooth was approximated by a circle for convenience in the present analysis. In order to estimate the elastic deformation of the gear and dies during cold sizing, linear elastic finite element analysis was performed. Results of the analysis can be used to predict grain flows and strength distributions in the forged gear, and to design dies and an appropriate preform for the cold sizing.

• 비파괴검사학회지
• /
• 제25권4호
• /
• pp.304-310
• /
• 2005

용접부 및 구조물에 발생된 결함의 깊이를 정밀하게 측정하기 위한 노력은 현재까지 계속되어 왔으며 앞으로도 계속되어야 할 연구분야중의 하나이다. TOFD 검사기법은 현재까지 결함의 깊이를 측정하기 위한 여러 가지 검사 방법중에 가장 정밀한 것으로 알려져 있다. 그러나 사용하는 초음파 굴절각에 따른 빔의 도달범위에 의하여 결함을 놓칠 우려가 있다. 본 여구에서는 일반적인 TOFD 기법대신 위상배열 초음파 기법을 이용한 TOFD 검사를 적용하여 두께가 두꺼운 검사대상에 대하여 결함의 검출능 및 깊이 측정결과를 비교하였다. 위상배열 초음파를 이용한 TOFD 검사를 사용함으로써 다양한 결함에 대하여 검출능 및 정확한 깊이 측정이 가능함을 실험적으로 확인하였다. 본 연구에서 개발된 위상배열 TOFD 기법은 발전설비의 압력용기와 같은 두꺼운 검사대상에 적용될 경우 검사 신뢰도 향상에 기여할 것으로 판단된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.273-274
• /
• 2007

• 비파괴검사학회지
• /
• 제1권1호
• /
• pp.6-12
• /
• 1981

소위 Satellite-Pulse Technique(SPT)을 이용하여 인공결함의 크기를 측정하였다. 측정치와 실제치를 비교하였는바 오차는 무시할 정도이었다.

• 한국압력기기공학회 논문집
• /
• 제6권1호
• /
• pp.29-36
• /
• 2010

Ultrasonic inspection of heavy walled cast austenitic stainless steel(CASS)welds is very difficult due to complex and coarse grained structure of CASS material. The large size of anisotropic grain strongly affects the propagation of ultrasound by severe attenuation, change in velocity, and scattering of ultrasonic energy. therefore, the signal patterns originated from flaws can be difficult to distinguish from scattered signals. To improve detection and sizing capability of ID connected defect for heavy walled CASS piping welds, the low frequency segmented TRL Pulse Echo and Phased Array probe has been developed. The experimental studies have been performed using CASS pipe mock-up block containing artificial reflectors(ID connected EDM notch). The automatic pulse echo and phase array technique is applied the detection and the length sizing of the ID connected artificial reflectors and the results for detection and sizing has been compared respectively. The goal of this study is to assess a newly developed ultrasonic probe to improve the detection ability and the sizing of the crack in coarse-grained CASS components.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.76-82
• /
• 1997

The discrimination of flaw shape and sizing is very important subject in the material evaluation for semiconductor and new materials. The aim of this paper is to investigate the spectrum analysis of artificial defect signal captured from steel ball embedded in the resin. The results show that it can be evaluated quantitatively the size of artificial defect, from the amplitude variation of same frequency if the probe with same diameter and focal length is used. Comparing with the amplitude variation of the high frequency component and low frequency component obtained from the distance of defect center position, it can be estimated steel ball and flat bottm defect.

• 비파괴검사학회지
• /
• 제7권1호
• /
• pp.42-50
• /
• 1987

Most of significant defects in the pressure boundaries of nuclear power plant we re dispositioned to be monitored periodically every inservice inspection. Due to the difficulty of the defect sizing during operation, it is necessary to develope the continuous flaw monitoring techniques. The Tip Diffraction method, specifically speaking, spot seems to be suitable for flaw monitoring. The optimum conditions of selecting the transducer were 3.5 MHz and 45-57 degree according to compatibility with the defect height. The effective calculation of the defect height was to assume the fact that the incident beam is parallel. This method would be supplemented to ASME method about the defect characterization for the surface flaw.