• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.95-107
• /
• 2007

This study starts to find a way out, experiment and apply commercial UV coatings to the cap closures. The cap closures is made form coating and succeeding deformation process. It is coated with several printing layers, printing and over print varnish coating. Then it pressed in three steps of press called 'deep-drawing'. In this study, two kinds of coating was designed and accomplished in the base of the same manufacturing and environment conditions. Consequently, UV curable ink have adequate performance in this experiment (T-bending, Erichsen Test), but it were experienced several damages in this experiments (web-bending, impact test). They were not cured enough to endure the friction and a unique shape of serial cracks were appeared.

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.58-67
• /
• 1998

A sectional analysis of sheet metal forming process with an arbitrary tool shape is proposed in the present work. To improve the numerical convergence in the conventional membrane sectional analysis, the Bending Energy Augmented Membrane (BEAM) elements had been developed. The BEAM elements particularly improve the stability and convergence of the finite element method for the case of deep drawing. In this work, the FERGUBON spline (C$^2$-continuous) was used to fit the deformed mesh to smooth the given curves and calculate the local curvature of the deformed sheet. The fittings of the deformed sheet and tool surface profile ensure the stability and the convergence of the finite element analysis of highly nonlinear stamping processes. A center floor section and front fender section are analyzed to show the accuracy and robustness of the approach. The results obtained by the proposed approach are compared with the available experimental data.

• 소성∙가공
• /
• 제11권5호
• /
• pp.430-438
• /
• 2002

This paper suggests the new technology to control metal flow in orther to change of the cold forging from conventional deep drawing forming. This technology can be summarized the complex forming, which consists of bulk forming and sheet forming, and multi-action forging, which be performed double action press. The proposed technology is applied to hub clutch model which is part of auto-transmission for automobile. The purpose of this study is to investigate the material flow behavior of hub clutch through control the relative velocity ratio and the stroke of mandrel and punch using the flow forming technique. First of all, the finite element simulations are applied to analyse optimal process conditions to prevent flow defect(necking defect etc.) from non-uniform metal flow, then the results are compared with the plasticine model material experiments. The punch load for real material is predict from similarity law. Finally, the model material experiment results are in good agreement with the FE simulation ones.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.146-154
• /
• 1996

In this work, rapid prototyping and three-dimensional finite element analysis are simultaneously applied to the die design of metal forming processes. Rapid prototyping is a new prototyping technology which produces three-dimensional part models directly from CAD data and has been extensively applied to various manufacturing processes. There are many types of rapid prototyping systems due to their building principles and materials. In this work, Stereolithography Apparatus(SLA), which is the most widely used rapidprototyping system, is introduced to manufacture the die set. For general preparation of STL file, which is the standard input file of rapid prototyping system, mesh data which are used in describing the die surface in finite element analysis are translated so that rapid prototyping and finite element analysis are dffectively connected. A die set for spider forging and a clover punch for deep drawing section are manufactured effciently using SLA prototypes, and metal forming experiments are carried out using them. Comparing the result of experiments with that of analyses, the processes can be predicted and designed successfully.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.555-559
• /
• 2005

Spinning process is a chipless metal forming method for axis-symmetric parts, which is more economical, efficient and versatile method for producing parts than other sheet metal forming process such as stamping or deep drawing. The large-sized spindle for spinning machine is the equipment to ferm a high-pressure vessel into the demanded shape. The important problem in the spindle system fur spinning machines is to reduce and minimize the thermal effect by motor and bearings. In this study, the effect of heat generation of bearings for the large-sized spindle is considered. Temperature distribution and thermal displacement of the spindle system for spinning machine can be analyzed by using the finite element method. The numerical results are compared with the measured data. The results show that temperature distribution and thermal displacement can be reasonably estimated by using the finite element method and the three dimensional model.

• 한국학교수학회논문집
• /
• 제12권2호
• /
• pp.151-170
• /
• 2009

초등학생에게 분수는 추상적인 개념이며 형식화된 이해를 요구하는, 핵심적인 수학적 기초 내용이다. 초등학교 수학에서 중학교 수학으로 연계되는 내용의 위계 구조상 적지 않은 영향력을 끼치는 내용 중 하나가 초등수학에서의 분수 학습일 것이다. 이에 본 연구에서는 초등학교 6학년생에게 나타난 분수 개념에 대한 이해와 오류를 분석하고 초등학교 학생이 가장 어려워하는 분수 나눗셈에 대한 표현 능력을 살펴봄으로써 초등수학에서의 시사점을 제공하고자 한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.467-470
• /
• 2005

There are about 10 motors for tile actuator of the automation system in an auto-mobile recently. The performance of the motor-case is much related to the noise and the vibration of an auto-mobile Multi-Forming process is so much the better than existing deep-drawing or Multi-step forming by press by less cost, installation and staff. But there isn't the specific and general process design, so we aren't good at competition. So in the first step, I want to study about the core design for the multi-forming process. We can access by the elasto-plastic theory and the finite element method, and we use a commercial package of the Deform-2D and, Deform-3D which is based on three-dimensional elasto-plastic finite element, evaluated propriety oi the package. The evaluation of the package propriety was simulated by simple bending example. It was found the elasto-plastic theory was mostly in agreement with the simulation. We proposed that three type of section for the core and analyzed by finite element method (Deform-2D). We can get the best result with the ellipse type core. Then we apply the result of the preceding analysis to the finite element method (Deform-3D). In 3D-finite element analysis, we can get the result of 8/100mm-roundness. This result can help the improvement of the multi-forming process.

• 대한기계학회논문집A
• /
• 제40권10호
• /
• pp.887-894
• /
• 2016

압축천연가스(CNG) 압력용기는 D.D.I공정을 통해 실린더부를 제작한 후, 스피닝 공정을 통해 돔 부 성형이 이루어진다. 그러나 스피닝 공정의 입구 부 성형에 관한 연구는 미미하며, 현장 작업자들의 경험이나 시행착오에 의해 제작되고 있는 실정이다. 이에 본 연구에서는 이론 임계좌굴하중 및 유한요소해석에서 축 방향 하중의 비교를 통하여 좌굴발생을 예측하였고, 상용 소프트웨어를 이용하여 돔부의 좌굴 방지를 위한 방법을 제안하였다. 또한, 입구 부 성형을 위하여 돔 부와 롤러가 맞닿는 점에서의 돔부의 반경에 따른 롤러 하중을 분석하고, 이를 토대로 입구 부 성형을 수행하였다.

• 한국산학기술학회논문지
• /
• 제18권6호
• /
• pp.330-335
• /
• 2017

최근 자동차 산업에서 전기 모터 연료 전지에 대한 수요가 급증했으며, 연료 전지 케이스로 사용되는 사각형 알루미늄 캔에 대한 수요 또한 증가하고 있다. 직사각형 배터리 케이스의 바닥에 있는 에어 벤트는 비정상적으로 높은 압력이 발생할 때 미리 압력을 방출하여 큰 폭발을 방지하는 역할을 한다. 직사각형 컵 배터리 케이스는 6 단계의 다단계 딥 드로잉으로 외형을 만들고 직사각형 배터리 케이스와 용접하여 벤트 부품을 제작해왔다. 그러나 본 연구에서는 직사각형 케이스의 바닥면에 공기 벤트 형상을 직접 추가 하는 연구를 수행하였다. 단조의 초기 형상으로는 사각 컵 다단식 딥 드로잉 성형 해석에서 추출한 두께와 형상을 이용한 유한 요소 해석 기법을 사용 하였다. 그 결과, 예측 정밀도가 향상되고, 배부름 및 파단 등의 결함을 미리 예측할 수 있었다. 초기 분석 결과를 토대로 두 가지 단조 형상이 후보로 제시되었고 성형 해석을 통해 최적의 단조 형상을 결정 하였다. 이러한 결과를 바탕으로 금형을 제작하고 실제 결과와 분석 결과를 비교하여 본 연구의 타당성을 검증하였다.

• 소성∙가공
• /
• 제17권7호
• /
• pp.501-506
• /
• 2008

In this study, a forming magnesium alloy circular cup was simulated accounting for heat transfer at elevated temperatures. In order to predict the failure of magnesium alloy sheet during simulation, the forming limit diagram, which is used in sheet metal forming analysis to determine the criterion for failure, was investigated. For the failure prediction in the simulation accounting for heat transfer, the forming limit diagram for a temperature the same as the temperature of the blank element was used. The result of the simulation showed that the drawn depth increases with the increase of the die-holder temperature, and is in accord with the experimental results above the die-holder temperature of $150^{\circ}C$. The forming limit diagram provided a good guide for the failure prediction of warm forming simulation accounting for heat transfer. In addition, the effect of the tool shoulder radius on the drawn depth at various tool temperatures is verified using the simulation conditions which agreed with the experimental results.