• Journal of Ocean Engineering and Technology
• /
• v.31 no.4
• /
• pp.288-298
• /
• 2017

A study of the damage evolution laws for ductile materials was carried out to predict the ductile fracture behavior of a marine structural steel (EH36). We conducted proportional and non-proportional stress tests in the experiments. The existing 3-D fracture strain surface was newly calibrated using two fracture parameters: the average stress triaxiality and average normalized load angle taken from the proportional tests. Linear and non-linear damage evolution models were taken into account in this study. A damage exponent of 3.0 for the non-linear damage model was determined based on a simple optimization technique, for which proportional and non-proportional stress tests were simultaneously used. We verified the validity of the three fracture models: the newly calibrated fracture strain model, linear damage evolution model, and non-linear damage evolution model for the tensile tests of the asymmetric notch specimens. Because the stress evolution pattern for the verification tests remained at mode I in terms of the linear elastic fracture mechanics, the three models did not show significant differences in their fracture initiation predictions.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.2
• /
• pp.85-90
• /
• 2008

Ships in bad weather conditions are likely to be subjected to accidental loads, such as high bending moment, collision, and grounding. Once she has damage to her hull, her ultimate strength will be reduced. This paper discusses an investigation of the effect of collision damage on the ultimate strength of a ship structure by performing a series of collapse tests. For the experiment, five box-girder models with stiffeners were prepared with a cross section of $720mm\;{\times}\;720mm$ and a length of 900mm. Of the five, one had no damage and four had an ellipse shaped damage area that represented the shape of the bulbous bow of a colliding ship. The amount of damage size was different between models. Among the damaged models, the damage in three of them was made by cutting the plate and stiffener, and in one by pressing to represent collision damage. Experiments were carried out under a pure bending load and the applied load and displacements were recorded. The ultimate strength was reduced as the damage size increased, as expected. The one with the largest amount of damage had damage to 30% of the depth, and its ultimate strength was reduced by 19% compared to the undamaged one. The pressed one has higher ultimate strength than those that were cut. This might be due to the fact that the plate around the pressed damage area contributes to the ultimate strength, whereas the cut one has no plate to contribute.

• KCI Concrete Journal
• /
• v.13 no.2
• /
• pp.67-74
• /
• 2001

In this study, a numerical model for the simulation of reinforced concrete columns subject to cyclic loading is presented. The model consists of three separate models representing concrete, reinforcing steel bars and bond-slip between a reinforcing bar and ambient concrete. The concrete model is represented by the plane stress plastic-damage model and quadrilateral finite elements. The nonlinear steel bar model embedded in truss elements is used for longitudinal and transverse reinforcing bars. Bond-slip mechanism between a reinforcing bar and ambient concrete is discretized using connection elements in which the hysteretic bond-slip link model defines the bond stress and slip displacement relation. The three models are connected in finite element mesh to represent a reinforced concrete structure. From the numerical simulation, it is shown that the proposed model effectively and realistically represents the overall cyclic behavior of a reinforced concrete column. The present plastic-damage concrete model is observed to work appropriately with the steel bar and bond-slip link models in representing the complicated localization behavior.

• Smart Structures and Systems
• /
• v.6 no.1
• /
• pp.17-27
• /
• 2010

The approach to damage detection and localization adopted in this paper is based on a statistical comparison of models built from the response time histories collected at different stages during the structure lifetime. Some of these time histories are known to have been recorded when the structural system was undamaged. The consistency of the models associated to two different stages, both undamaged, is first recognized. By contrast, the method detects the discrepancies between the models from measurements collected for a damaged situation and for the undamaged reference situation. The damage detection and localization is pursued by a comparison of the SSE (sum of the squared errors) histograms. The validity of the proposed approach is tested by applying it to the analytical benchmark problem developed by the ASCE Task Group on Structural Health Monitoring (SHM). In the paper, the results of the benchmark studies are presented and the performance of the method is discussed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.1-8
• /
• 2013

This study investigates life and damage due to structural and fatigue load at speaker placer with wall hanger type. As the small stress and deformation are shown at the models of A, B and C shapes on structural analysis, there is no problem at installing speaker placer. As the largest stress is happened at the middle part of joint on the models of A, B and C shapes, this part must be considered at the design. A shape is thought to have most fatigue damage among 3 shape models. C shape model has most excellent, but A model has least at fatigue durability. This study result is applied with the design of speaker placer and it can be useful at predicting prevention and durability against its damage.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.21-36
• /
• 2018

The incidence of collision damage models on oil tanker and bulk carrier reliability is investigated considering the IACS deterministic model against GOALDS/IMO database statistics for collision events, substantiating the probabilistic model. Statistical properties of hull girder residual strength are determined by Monte Carlo simulation, based on random generation of damage dimensions and a modified form of incremental-iterative method, to account for neutral axis rotation and equilibrium of horizontal bending moment, due to cross-section asymmetry after collision events. Reliability analysis is performed, to investigate the incidence of collision penetration depth and height statistical properties on hull girder sagging/hogging failure probabilities. Besides, the incidence of corrosion on hull girder residual strength and reliability is also discussed, focussing on gross, hull girder net and local net scantlings, respectively. The ISSC double hull oil tanker and single side bulk carrier, assumed as test cases in the ISSC 2012 report, are taken as reference ships.

• Earthquakes and Structures
• /
• v.9 no.5
• /
• pp.957-981
• /
• 2015

Earthquakes occur as a cluster in many regions around the world where complex fault systems exist. The repeated shaking usually induces accumulative damage to affected structures. Damage accumulation in structural systems increases their level of degradation in stiffness and also reduces their strength. Many existing analytical tools of modeling RC structures lack the salient damage features that account for stiffness and strength degradation resulting from repeated earthquake loading. Therefore, these tools are inadequate to study the response of structures in regions prone to multiple earthquakes hazard. The objective of this paper is twofold: (a) develop a tool that contains appropriate damage features for the numerical analysis of RC structures subjected to more than one earthquake; and (b) conduct a parametric study that investigates the effects of multiple earthquakes on the response of RC moment resisting frame systems. For this purpose, macroscopic constitutive models of concrete and steel materials that contain the aforementioned damage features and are capable of accurately capturing materials degrading behavior, are selected and implemented into fiber-based finite element software. Furthermore, finite element models that utilize the implemented concrete and steel stress-strain hysteresis are developed. The models are then subjected to selected sets of earthquake sequences. The results presented in this study clearly indicate that the response of degrading structural systems is appreciably influenced by strong-motion sequences in a manner that cannot be predicted from simple analysis. It also confirms that the effects of multiple earthquakes on earthquake safety can be very considerable.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.71-76
• /
• 2002

In this study low cycle fatigue (LCF) behavior of 12Cr steel at high temperature are described. Secondly, comparisons between predicted lives and experimental lives are made for the several sample life prediction models. Two minute hold period in either tension or compression reduce the number of cycles to failure by about a factor of two. Twenty minute hold periods in compression lead to shorter lives than 2 minute hold periods in compression. Experiments showed that life predictions from classical phenomenological models have limitations. More LCF experiments should be pursued to gain understanding of the physical damage mechanisms and to allow the development of physically-based models which can enhance the accuracy of the predictions of components. From a design point-of-view, life prediction has been judged acceptable for these particular loading conditions but extrapolations to thermo-mechanical fatigue loading, for example, require more sophisticated models including physical damage mechanisms.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.1
• /
• pp.41-46
• /
• 2004

This paper describes a study on the tearing damage of a ship's bottom plating, during a grounding. It is widely known that different scaling laws are applied for bodies undergoing simultaneous plastic flow and crack propagation in the deformation of plate tearing. Specifically, the basic scaling law is not followed for the fracture. In this study, in order to verify the problem, plate cutting experiments for geometrically similar models have been performed. From the experimental results, it has been observed that the cutting forces and energy for the larger models are significantly lower than those of the smaller models. A simplified analytical method for the estimation of tearing is proposed, based on the experiments. It has been observed that the results of the present formula are highly correlated with the experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.119-127
• /
• 2006

A non-destructive time domain approach to examine structural damage using parameterized partial differential equations and Galerkin approximation techniques is presented. The time domain analysis for damage detection is independent of modal parameters and analytical models unlike frequency domain methods which generally rely on analytical models. The time history of the vibration response of the structure was used to identify the presence of damage. Damage in a structure causes changes in the physical coefficients of mass density, elastic modulus and damping coefficients. This is a part of our ongoing effort on the general problem of modeling and parameter estimation for internal damping mechanisms in a composite beam. Namely, in detecting damage through time-domain or frequency-domain data from smart sensors, the common damages are changed in modal properties such as natural frequencies, mode shapes, and mode shape curvature. This paper examines the use of beam-like structures with piezoceramic sensors and actuators to perform identification of those physical parameters, and detect the damage. Experimental results are presented from tests on cantilevered composite beams damaged at different locations and different dimensions. It is demonstrated that the method can sense the presence of damage and obtain the position of a damage.