• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2078-2086
• /
• 1999

Fracture behaviors of an interface crack in a ductile layer sandwiched by rigid substrates are analyzed by finite element method. Several fracture mechanisms and the corresponding criteria are examined. And the crack growth behavior and fracture toughness are predicted. As the results, various crack growth procedures such as the crack jump to the other interface on the opposite side, the creation of a new crack far from the initial crack front, and the asymmetric relation of fracture toughness vs. mode mixity ($J_c$-$\Phi$) can be successfully explained.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.156-162
• /
• 2000

Sensitized STS 304 stainless steel crack growth rate(CGR) in high temperature water was investigated under trapezoidal wave loading test using fracture mechanics techniques. The CGR, due to stress corrosion cracking(SCC), were systematically measured as a function of the stress intensity factor and stress. holding time under trapezoidal wave loading. In high temperature water, CGR was enhanced by a synergistic effects in combination with an aggressive environment and mechanical damage. The CGR, $(da/dN)_{env}$ was basically described as a summation of the environmentally assisted crack growth rate $(da/dN)_{SCC}$, $(da/dN)_{CF}$ and fatigue crack growth rate in air $(da/dN)air,. The CGR, $(da/dN)_{env}$, increased linearly with increasing stress holding time. The CGR, $(da/dN)_{SCC}$ decreased linearly with increasing stress holding time. Fracture surface mode varied from trans-granular cracking to inter-granular cracking with increasing stress holding time.

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.960-968
• /
• 2002

In this research, the effects of fiber stacking sequence on damage behaviors of FML(Fiber Metal Laminates) subject to indentation loading. SOP (Singly Oriented Ply) FML and angle ply FML were fabricated to study fiber orientation effects and angle ply effects. FML were fabricated by using 1050 aluminum laminate and carbon/epoxy prepreg. To increase adhesive bonding strength, Al laminate was etched using FPL methods. The static indentation test were conducted by using UTM under the 2side clamped conditions. During the tests, load and displacement curve and crack initiation and propagation behaviors were investigated. As fiber orientation angle increases, the crack initiation load of SOP FML increases because the stiffness induced by fiber orientation is increased. The penetration load of SOP FML is influenced by the deformation tendency and boundary conditions. However, the macro-crack of angle ply FML was initiated by fiber breakage of lower ply because angle plies in Angle ply FML prevents the crack growth and consolidation. The Angle ply FML has a critical cross-angle which prevent crack growth and consolidation. Damage behavior of Angle ply FML is changed around the critical cross-angle.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.14-21
• /
• 2001

To estimate crack growth rate and cycle ratio uniquely, many investigators have developed various kinds of mechanical parameters and theories. But, thes have produced local solution space through single parameter. Neural Networks can perform patten classification using several input and output parameters. Fatigue damage model by neural networks was used to recognize the relation between da/dN/N/N(sub)f, and half-value breadth ratio B/Bo, fractal dimension D(sub)f, and fracture mechanical parameters in 2024-T3 aluminium alloy. Learned neural networks has ability to predict both crack growth rate da/dN and cycly ratio /N/N(sub)f within engineering estimated mean error(5%).

• 터널과지하공간
• /
• 제20권1호
• /
• pp.65-72
• /
• 2010

암반발파에서 평활한 파단면을 확보하고 굴착손상영역을 제어하기 위하여 노치장약공을 이용한 균열제어공법이 제안되었다. 본 연구에서는 노치형상과 장약조건이 균열발생 및 성장에 미치는 영향을 살펴보기 위하여 날개형 노치장약공을 갖는 발파모델을 구축하고 동적 파괴과정 해석법을 이용한 암반 파괴과정 해석을 수행하였다. 그 결과, 노치 길이가 증가함에 균열의 성장 길이가 증가하며 파단면의 거칠기가 감소하고 장약공 상하부에 손상균열의 발생이 억제되는 경향을 보였다. 해석결과로부터 노치 길이 및 개구 폭에 따른 응력집중계수의 변화 및 균열발생 양상을 비교 분석하여 균열제어에 미치는 영향인자에 대하여 고찰하였다.

• Composites Research
• /
• 제16권4호
• /
• pp.44-50
• /
• 2003

균열선단에 발생하는 손상역은 재료의 파괴인성 메카니즘을 알 수 있게 하는 중요한 영역이다. 본 연구에서는 고무변성 에폭시 수지의 균열선단 손상역의 생성 및 성장 과정을 음향방출법을 이용하여 조사하였다. 고무변성 에폭시 수지의 고무함량은 5 wt%와 15 wt%로 하였고, 3점 굽힘시험편을 사용하여 모드 I 파괴시험에 대한 각 시험편의 파괴인성값을 구하였다. 또한, 균열선단의 손상역과 그 내부의 고무입자 변형상태를 편광현미경과 원자력간 현미경을 사용하여 관찰하였다. 고무변성 에폭시 수지의 균열선단부의 손상역은 파괴하중의 약 13 % 하중에서 생성이 되어, 약 57 % 하중까지 균열개시 없이 성장하였다. 57 % 하중 근처에서 개시만 균열은 최대하중부근까지 고착-활강거동을 반복하면서 안정 / 불안정 파괴로 진전하였다 이 과정에서 발생한 음향방출신호의 시간-주파수 분석결과, 고투입자 내부에서의 케비테이션 생성단계에서 주파수대역은 0.15 ∼ 0.20 MHz 이었고, 그 후의 안정 및 불안정시의 주파수 대역은 0.20∼0.30MHz 이었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.337-340
• /
• 2005

The effect of residual stress on fatigue crack growth was investigated in terms of finite element analysis. Simulations were performed on a CT specimen in plane strain. An interface-cohesive element that accounts for damage accumulation due to fatigue along the notch direction has been used. Numerical results show that fatigue crack growth rate slows down when compressive residual stress field exists in front of the crack tip.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.228-229
• /
• 2005

The compressive residual stress, which is induced by shot peening process, has the effect of increasing the intrinsic fatigue strength of surface and therefore would be beneficial in reducing the probability of fatigue damage. However, it was not known that the effect of shot peening in corrosion environment. In this study, the effect of shot peening on corrosion fatigue crack growth of sping steel immersed in 6% $FeCl_3$ solution and corrosion characteristics with considering fracture mechanics. The results of the experimental study corrosion fatigue characteristics of spring steel are as follows; the fatigue crack growth rate of the shot peening material was lower than of the un peening material. And fatigue life shows more improvement in the shot peening material than un peening material. This is because the compressive residual stress of surface operate resistance of corrosion fatigue crack propagation. It is assumed that the shot peening process improve corrosive resistance and mechanical property.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.100-107
• /
• 1999

This paper describes a probabilistic remaining life assessment program for the creep crack growth. The probabilistic life assessment program is developed to increase the reliability of life assessment. The probabilistic life assessment involves some uncertainties, such as, initial crack size, material properties, and loading condition, and a triangle distribution function is used for random variable generation. The resulting information provides the engineer with an assessment of the probability of structural failure as a function of operating time given the uncertainties in the input data. This study forms basis of the probabilistic life assessment technique and will be extended to other damage mechanisms.

• 항공우주시스템공학회지
• /
• 제1권2호
• /
• pp.27-36
• /
• 2007

The Damage Tolerant Design is developed to help alleviate structural failure and cracking problems in aerospace structures. Recently, the Damage Tolerant Design is required and recommended for most of aircraft design. In this paper, the damage tolerant design is applied to tilt rotor UAV. First of all, the fatigue load spectrum for the tilt rotor UAV is developed and fatigue analysis is performed for the flaperon joint which has FCL (fatigue critical location). Tilt rotor UAV has two modes: helicopter mode when UAV is taking off and landing; fixed wing mode when the tilt rotor UAV is cruising. To make fatigue load spectrum, FELIX is used for helicopter mode. TWIST is used for fixed wing mode. Fatigue analysis of flaperon joint is performed using fatigue load spectrum. E-N curve approach is used for picking crack initiation point. The LEFM(Linear Elastic Fracture Method) is considered for analyzing crack growth or propagation. Finally, including the crack initiation and propagation, the fatigue life is evaluated. Therefore the Damage Tolerant Design can be done.