• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.9
• /
• pp.1165-1171
• /
• 2020

In this study, we designed a single antenna taking into account the performance, such as return loss and radiation pattern, of 28 GHz and 38 GHz array antennas for 5G mobile devices. In millimeter wave band communication, high path loss occurs between transmission and reception, unlike in conventional microwave bands. In the design of array antennas for 5G millimeter wave terminals, antenna performance such as antenna gain, bandwidth, isolation between antenna elements, side-lobe level(SLL), etc. should be further considered. The performance of the designed array antennas was analyzed by spacing the antenna elements at half a wavelength. Our results proved the validity of the design and its suitability for applications in mm-Wave by showing that the 28 GHz and 39 GHz array antennas had antenna gains of 13.5 dBi and 11.3 dBi and return losses below -18.4 dB and -20 dB, correspondingly.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.3 s.76
• /
• pp.271-283
• /
• 2005

This paper concerns the prediction of shear capacity, as governed by steel failure and concrete breakout failure, of set anchors installed in plain concrete. For this purpose, the methods to evaluate the shear capacity of the set anchors in concrete are summarized and the experimental data are compared with capacities by the two present methods : the method of ACI349-90 and the Concrete Capacity Design (CCD) method. (1) The constant-0.684 in the steel strength equation of set anchor was determined from shear test data at the 5 percent fractile probability. Consequently, it was concluded that the constant-0.6 and 0.5 in the steel strength equation for steel failure of ACI318-02 and EOTA were safe. The nominal shear strength of set anchor was proposed as following. $V_s=0.684 A_{se}f_{ut}$. (2) The CCD method was considered reasonable in estimating the concrete breakout strength of set anchors. In terms of the CCD method, the nominal concrete breakout strength of set anchor in shear was provided as follows; $V_b=0.609(\frac{\iota}{d_o})^{0.2}\sqrt{d_0}\sqrt{f_c}(c_1)^{1.5}$(N). (3) The CCD method was considered reasonable in estimating the concrete breakout strength for spacing of set anchors. The proposed equation was considered safe in estimating the concrete breakout strength for spacing of set anchors.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.559-565
• /
• 2014

A 3 dB coupler has been designed and implemented using the most commonly used double-sided FR4 boards. The coupling and the bandwidth of the coupler are enhanced with the enlarged overlapped area of the coupler. Major design parameters are plotted as a design guide and the parameters are verified by simulation and measurement. The size of the manufactured coupler is $30{\times}14mm^2$. Its measured insertion loss and phase difference are 0.6 dB and $90.5^{\circ}$ at center frequency of 2.5 GHz, respectively. The operating frequency range is 1.72 GHz to 3.08 GHz for $3.6{\pm}0.5dB$ insertion loss. The coupler has the performance similar to that of conventional Lange coupler, and implementation of the coupler is easy and cheap with wide metal width and spacing and no additional wire bonding process.

• Journal of electromagnetic engineering and science
• /
• v.12 no.4
• /
• pp.254-259
• /
• 2012

This paper presents a closely spaced two-element folded-dipole-driven quasi-Yagi array with low mutual coupling between adjacent elements. The antenna utilizes a T-junction power divider as the feeding network, with an input impedance of $50{\Omega}$. A microstrip-stub is added to the ground plane in the middle of the two elements to improve the mutual coupling characteristics. The folded dipole driver is connected to a $50{\Omega}$ microstrip line via a broadband microstrip-to-coplanar stripline transition with a quarter radial stub. A mutual coupling of less than -22 dB is measured between two folded-dipole-driven quasi-Yagi antennas with a center-to-center spacing of 30 mm ($0.55{\lambda}_0$ at 5.5 GHz). The proposed quasi-Yagi array yields a measured bandwidth of 4.75~6.43 GHz for the -10 dB reflection coefficient and a gain of 6.14~7.12 dBi within the bandwidth range.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.62-70
• /
• 2009

In this paper, the fluid flow behavior past a pair of rectangular cylinders placed in a two dimensional horizontal channel has been investigated using Lattice-Boltzmann Method(LBM). The LBM has built up on the D2Q9 model and the single relaxation time method called the Lattice-BGK(Bhatnagar-Gross-Krook)model. Streamlines, velocity, vorticity and pressure contours are provided to analyze the important characteristics of the flow field for a wide range of non dimensional parameters that present in our simulation. Special attention is paid to the effect of spacing(d) between two cylinders and the blockage ratio A(=h/H), where H is the channel height and h is the rectangular cylinder height. for different Reynolds numbers. The first cylinder is called upstream cylinder and the second one as downstream cylinder. The downstream fluid flow fields have been more influenced by its blockage ratios(A) and Reynolds numbers(Re) whereas the upstream flow patterns(in front of downstream cylinder) by the gap length(d) between two cylinders. Moreover, it is observed that after a certain gap, both upstream and downstream flow patterns are almost similar size and shape. The simulation result has been compared with analytical solution and it is found to be in excellent agreement.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.44-50
• /
• 2002

A new wavelength demultiplexing scheme using holographic volume phase grating formed in photopolymer is proposed and demonstrated. Through the analysis and experiments of the design parameters such as wavelength selectivity, operating spectral range, spatial channel distance and spatial intensity distribution of each channel, we proved that the proposed demultiplexing scheme is promising for wavelength division multiplexing (WDM). From the experimental results, the 3 dB bandwidth of 0.21nm and the crosstalk level of 26 dB for a 0.8 nm channel spacing are observed.

• Progress in Medical Physics
• /
• v.1 no.1
• /
• pp.23-29
• /
• 1990

In order to explane the stereotactic procedure, the three steps of the procedure (target localization, dose planning, and radiation treatment) must be examined separately. The ultimate accuracy of the full procedure is dependent on each of these steps and on the consistancy of the approach The concern in this article was about dose planning, which is a important factor to the success of radiation treatment. The major factor in dose planning is a dosimetry system to evaluate the dose delivered to the target and normal tissues in the patient, while it generates an optimal dose distribution that will satisfy a set of clinical criteria for the patient. A three-dimensional treatment planning program is a prerequisite for treatment plan optimization. It must cover 3-D methods for representing the patient, the dose distributions, and beam settings. The major problems and possible modelings about 3-D factors and optimization technique were discussed to simplify and solve the problems associatied with 3-D optimization, with relative ease and efficiency. These modification can simplify the optimization problem while saving time, and can be used to develop reference dose planning system to prepare standard guideline for the selection of optimum beam parameters, such as the target position, collimator size, arc spacing, the variation in arc length and weight. The method yields good results which can then be simulated and tailored to the individual case. The procedure needed for dose planning in stereotactic radiosurgery is shown in figure 1.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.2
• /
• pp.54-59
• /
• 2014

The electric power can be converted into the mechanical power by a corona discharge system. This way has not stronger force than a electric motor. But it has been applied in various industrial fields because of many advantages, no moving parts, smaller noise, simpler structure, minimizing et al. In this paper, corona discharge system with multiple corona electrode installed in form of the ring, has been studied by focusing on the electrical and mechanical characteristics. Intensity of the corona discharge depends on applied electric field, and electric field is related to the applied voltage, discharge gap spacing(s), distance between each corona electrodes(d). As a result, in the case d/s=0.9, most intensive discharge occurred in this experiments. In the region of d/s<0.9, ionic wind velocity has saturation value in spite of decreasing corona current, because each ion velocities increase by the increasing electric field.

• Journal of Korea Foundry Society
• /
• v.34 no.1
• /
• pp.6-13
• /
• 2014

The mechanical properties of low-pressure die cast (LPDC) A356-T6 automotive road wheels are evaluated and correlated with their corresponding microstructures. In this study, two types of alloy wheels processed using different LPDC gating system are investigated. The yield stress, tensile stress, and elongation values tested at room temperature are correlated with the secondary dendrite arm spacing (SDAS) with respect to the gating system, and are also compared with similar studies. The SDAS and precipitates are examined using optical microscopy, scanning electron microscopy (SEM) and energy-dispersive spectroscopy. The phase information is also investigated using X-ray diffraction. Charpy impact tests are also performed from $-100^{\circ}C$ to $200^{\circ}C$, and the fracture surfaces are examined using SEM. The impact energy is demonstrated to increase with increasing temperatures without exhibiting specific transition behaviors as in other nonferrous alloys. The fracture toughness is also evaluated using three point bend test with single-edged bend specimens. The obtained fracture toughness values are in good agreement with those in similar studies.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.12-16
• /
• 2003

This paper presents a compensation method for a temperature-dependent gain tilt in L-band erbium-doped fiber amplifier using a voltage-controlled attenuator. The gain tilts in the L-band of 1570-1605 nm due to a temperature change have negative slopes, whereas they have positive slopes for the increasing optical input powers in a saturation region. The proposed method utilizes these opposite gain variations to compensate for the gain tilt over a wide range of temperature. While applying forty channels with a channel spacing of 100 GHz in the L-band and changing the ambient temperature from 0 to $50^{\circ}C$, the compensation method maintained the gain deviation within 1 dB.