• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.269-278
• /
• 2000

The pressure-time profile of the explosion gases can controlled for the use of cartridge explosive with two techniques known as Decoupling and spacing of the charges. Decoupling consists of a space between the explosive column and wall of the blast hole. Four different decoupling index 1.4, 1.8, 2.34, 3.0 are selected in this field study. The level of ground vibrations with each decoupling index was measured and the empirical particle velocity equation from these data was obtained. The condition of new cracks at blast hole are also examined. As the decoupling index is increased, the level of the blast vibration is decreased. But the cracks in rock masses are efficiently formed to remove the broken rock. The vibration constant associated with test sites is given as $K=1564.5(D.L)^{-1.3233}$ in terms of D.I.(decoupling index).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.195-196
• /
• 2000

A passband-flattening technique based on Fourier optics concept for phased-array wavelength router is presented. For easy control of optical power in each waveguide without phase correction, misaligned array waveguides are used. BPM simulation results indicate that flat passband is as wide as 75 % of the channel spacing with the insertion loss penalty of about 6 dB and with the crosstalk of about -28 dB.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.3
• /
• pp.405-409
• /
• 2009

A polarization-independent multiwavelength-switchable fiber filter is proposed based on a polarization beam splitter and fiber coupler, which can function as a polarization-independent transmission or reflection-type interleaving filter. The proposed filter consists of a polarization beam splitter and a Sagnac birefringence loop composed of a 50:50 coupler, high birefringent fibers, and two quarter-wave plates. In the proposed filter, a transmission-type interleaver with a channel isolation > 18 dB or a reflection-type one with a channel isolation of ${\sim}3$ dB, whose channel spacing and switching displacement were 0.8 and 0.4 nm in common, respectively, could be obtained. A channel interleaving operation could be performed by the proper control of waveplates within the Sagnac birefringence loop.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.1-6
• /
• 2010

Aluminum rear lower arm is designed for luxury sedan and manufactured by hollow sand casting in the present study. Here we present the relationship between local microstructure and coupon tensile test in the rear lower arm. The characteristics of the local tensile deformation are supposed to be dependent upon Si distribution and DAS (dendrite arm spacing). Si distribution affects the yield strength and DAS affects the elongation of local area in the part, respectively.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1461-1467
• /
• 2005

In this study, a new earth retention system has been developed and introduced. This system is a self-supported earth retaining wall without struts. The new earth retention system consists of connected double H-pile and wale. This system provides a larger spacing of support, economical benefit, construction easiness, good performance and safety. This paper explains basic principles and mechanism of self-supported earth retaining wall. In order to investigate applicability and safety of this system, numerical analysis was performed. The finite differential method program, FLAC3D is used. The predicted performances of this system were presented and discussed.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.65-74
• /
• 2000

A five path ultrasonic and/or magnetic flowmeter were installed after valve. Five path ultrasonic flowmeter were tested to obtain it's performance in a water flow standard system and magnetic flowmeter. It's varied with straight pipe length(nD), install direction and valve position. All the results are summerized. The multi-path flowmeters(MUF) showed up to $\pm0.5{\%}$ at a 2, 4, 8, 15D spacing : the MUF was significantly better than magnetic flowmeter at disturbed flow conditions.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.345-349
• /
• 2000

A microstrip polarized 8${\times}$2 linear phased array antenna with four 4-bit phase shifters is designed at 10 GHz. The 180$^{\circ}$and 90$^{\circ}$ sections of the phase shifter are of the switched line type, and the rests are of the loaded line type. A 2${\times}$2 sequential sub-array is adopted for a broad axial ratio bandwidth. The construction of the array antenna is of the tile type placing the phase shifters on the same layer containing the feed network. The element spacing is chosen to be 0.45λ$\sub$0/ to exclude the grating lobe. Measurement results show a gain 9.69 dB at broadside and 8.3 dB at the beam-tilt angle of 16$^{\circ}$ by imposing a progressive phase of 90$^{\circ}$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.64-71
• /
• 1997

A new etching technique of meltback was investigated for GaAs lensed optical devices with selective windows opending in the LPE (liquid phase epitaxy) system. In the meltback process, the etch depth and the etch shape were controlled by the degree of under-saturation, etch time and other parameters. A GaAs/AlGaAs DH layer was grown on the selectively etched hemispherical well for optical device application such as lensed surface emitting LED. The regrowth process were related with the coolin grate and the well to well spacing. A novel surface emitting LED with hemispherical AlGaAs lens was fabricated using the meltbakc and regrowth as the key process for AlaAs lens array. The light emitting efficiency of the LED was upto three times higher than the similar structure LED without lens. The meltback and regrowth technique was applicable to manufacture the optical device in LPE.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.227-227
• /
• 1999

Plasma display panel(PDP) is a leading technology for large-area flat panel displays. A current issue in operating the PDP cell is that the efficiency of the PDP cell is very low. To increase the efficiency of the PDP cell, the visible light needs to be maximized and the power consumption minimized. Since the excited xenons are related to the production of the visible light, it is important to optimize the cell geometry and the gas composition that produce the excited xenons more efficiently. A 2D-fluid code (FL2P) is developed and used to simulate the plasma dynamics and the radiation transport in the PDP cell. The cell is optimized with the code for various operating conditions and cell dimensions such as the voltage pulse, electrode length, electrode spacing, gap size, dielectric constant, gas mixture ratio, pressure, and pulse duration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.84-87
• /
• 2003

Carbon-nitrogen (CN) nanofibers have been produced using a water cooled hot isostatic pressure (HIP) apparatus. The CN nanofibers were grown in random with the diameter of about 100-150nm and length over $10{\mu}m$. Emission properties of CN nanofibers were investigated for spacing, between anode and cathode, variation. Then turn-on fields about $1.4V/{\mu}m$. The time reliability and light emission test were carried out for above 100 hours. We suggest that CN nanofibers can be possibly applied to high brightness flat lamp because of low turn-on field and time reliability.