• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.537-542
• /
• 2003

The stress-strain curve of concrete confined with both spiral and carbon fiber sheet(CFS) is different to that of concrete confined with only spiral or CFS. The objective of this study is to investigate the stress-strain relation of concrete confined by composite material. In this study, 24 concrete cylinders were tested. The main variable of the cylinders was the content rate of spiral to CFS. The test results indicated that while the compressive strength of cylinder confined with both spiral and CFS increased proportionally to the aided amount of two materials, the maximum strain of cylinder depended on the larger strain of spiral or CFS.

• Structural Engineering and Mechanics
• /
• v.75 no.1
• /
• pp.101-108
• /
• 2020

The present study intends to analyze damage in thin-walled steel cylinders undergoing constant internal pressure and thermal cycles through use of anisotropic continuum damage mechanics (CDM) model coupled with nonlinear kinematic hardening rule of Chaboche. Materials damage in each direction was defined based on plastic strain and its direction. Stress and strain distribution over wall-thickness was described based on the CDM model and the return mapping algorithm was employed based on the consistency condition. Plastic zone expansion across the wall thickness of cylinders was noticeably affected with change in internal pressure and temperature gradients. Expansion of plastic zone over wall-thickness at inner and outer surfaces and their boundaries demarking elastic and plastic regions was attributed to the magnitude of damage induced over thermomechanical cycles on the thin-walled samples tested at various pressure stresses.

• Journal of Mechanical Science and Technology
• /
• v.18 no.10
• /
• pp.1869-1879
• /
• 2004

The present study has numerically investigated two-dimensional flow over three circular cylinders in an equidistant side-by-side arrangement at a low Reynolds number. For the study, numerical simulations are performed, using the immersed boundary method, in the range of g* < 5 at Re= 100, where g* is the spacing between two adjacent cylinder surfaces divided by the cylinder diameter. Results show that the flow characteristics significantly depend on the gap spacing and a total of five kinds of wake patterns are observed over the range: modulation-synchronized (g* (equation omitted) 2), inphase-synchronized (g* (equation omitted) 1.5) , flip-flopping (0.3 < g* (equation omitted) 1.2) , deflected (g* (equation omitted) 0.3), and single bluff-body patterns (g* < 0.3). Moreover, the parallel and symmetric modes are also observed depending on g* in the regime of the flip-flopping pattern. The corresponding flow fields and statistics are presented to verify the observations.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1166-1173
• /
• 2004

In this paper, in order to apply magnetic fluid with superparamagnetic property as the substitute of ferromagnetic materials, physical properties of magnetic fluid are investigated. A targeted drug delivery system using a capsule filled magnetic fluid is proposed where a magnetic fluid capsule and cylinders are considered as a drug and vital organs, respectively. The dynamic governing equation of this system first is derived. Fluid viscosity, clearance between a cylinder and a magnetic fluid capsule, and levitation height with respect to different cylinder height are considered as major parameters to evaluate dynamic characteristics of the system. The experiments and simulations for the position control of the magnetic fluid capsule in various cylinders are conducted using PID controller. The results show that magnetic fluid with the superparamagnetic property can be applied to a targeted drug delivery system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.269-276
• /
• 2004

A marine diesel engine should realize optimal efficiency operation while reducing NOx. Fuel injection systems by electronic control can become effective means for that. Although it would be able to get more precise engine control compared to the mechanical injection system, it needs some accurate and instant information in order to bring its ability into full play while sailing on the sea. Very important information of them is shaft torque and continuous combustion pressure of all cylinders. The system presented in this report can deliver those data.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.3
• /
• pp.9-16
• /
• 1997

A numerical method based on the spectral collocation method is developed for the steady rotating flows in eccentric annulus. Steady flows between rotating cylinders are of interest on lubrication in large rotating machinery. Steady rotating flow is generated by the rotating inner cylinder with constant angular velocity. The governing equations for laminar flow are simplified from Navier-Stokes equations by neglecting the non-linear convection terms. Integrating the pressure round the rotating cylinder based on the half Sommerfeld method, the load on the cylinder is evaluated with eccentricity. The attitude angle and Sommerfeld variable are calculated from the load. It is found that those values are influenced by the eccentricity. The attitude and Sommerfeld reciprocal are decreased with eccentricity. As expected, the effect of the annular gap ratio on them is negligible.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.311-316
• /
• 2008

Thick-walled cylinders, such as a cannon or nuclear reactor, are autofrettaged to induce advantageous residual stresses into pressure vessels and to increase operating pressure and the fatigue lifetimes. As the autofrettage level increases, the magnitude of compressive residual stress at the bore also increases. The purpose of the present paper is to predict the accurate residual stress of SCM440 high strength steel using the Kendall model which was adopted by ASME Code. Hydraulic pressure process was applied and thick-walled cylinders were autofrettaged up to 30% overstrain levels. Electro polishing was performed to get more accurate data. Residual stresses were measured by X-ray diffraction method. The autofrettaged surface which was plastically deformed analyzed using a scanning electron microscope(SEM). Although there were some differences in measured residual stress and numerical, there is a tendency to agree.

• Journal of Drive and Control
• /
• v.9 no.1
• /
• pp.18-24
• /
• 2012

The paper deals with the design of a new low-friction seal for a pneumatic cylinder with high speed actuation. The seal performance with variation of the cross sections in piston seals with elastomeric material was investigated to minimize the friction forces using ABAQUS. The contact stress and strain distributions and frictional forces of the piston seals were investigated with variation of interference fits, supply pressures and friction coefficients. To develop adequate and productive procedures, the finite element models of the piston seals were created and nonlinear analysis of a seal design was conducted in order to build further knowledge and understanding of the seal's performance characteristics.

• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.14-20
• /
• 2013

In the study, a control strategy using a feedback linearization compensator and a disturbance observer was suggested and applied to the synchronization control of two hydraulic cylinders. The hydraulic system consists of a proportional directional control valve with overlap characteristic near the neutral position, a conventional hydraulic cylinder and an external load. The control performances of the system were verified through numerical simulations. From the simulations, it was ascertained that excellent control performances were obtained with the suggested control strategy.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.5
• /
• pp.573-580
• /
• 2002

Animation and time-resolved analysis of the wake characteristics of 2-D bluff body flows were examinated by applying the multi-vision PIV to square cylinders(three angles of attack: $0^{circ}, 30^{circ} and 45^{\circ}$) and circular cylinders(three rotating speeds: 0rpm, 76rpm, 153rpm) submerged within a circulating water channel $(Re=10^4)$, The macroscopic shedding patterns and their dominant frequencies were discussed in terms of instantaneous velocity, vorticity and turbulent quantities such as turbulent intensity, turbulent kinetic energy and three Reynolds stresses. Particularly the time-averaged distribution of turbulent intensity 'islands' where their peak magnitudes were focused always small regions behind the bodies without noticeable spatial migration were particularly discovered in all cases. And the dominant frequencies of the turbulent quantities in the wake regions were two times larger than those of the velocity and vorticity.