• Journal of the Korean Chemical Society
• /
• v.43 no.4
• /
• pp.407-411
• /
• 1999

Studies have been carried out on the fabrication of PPy/GC and PPy/Pt electrode modified with polypyrrole film and determination of Cr(VI) by using 3-electrode system with modified electrodes. Modified electrodes were able to easily fabricated by cyclic voltammetry scanned from +1.0V to -1.0V(vs. Ag/AgCl) at 50 mV/sec. Film thickness could be controlled at same condition by the number of cycling up to 26 times. Reduction behaviour of Cr(VI) at PPy/GC electrode could be seen at wide potential ranges from +0.6V to -0.5V(vs. Ag/AgCl), and maximum reduction peak potential of the ion was observed at -0.25V(vs.Ag/AgCl). Calibration graph at its potential was linear from 0.1 ppm to 80.O ppm. Slope factor and relative coefficient were 1.75 mA/ppm and 0.998, respectively. Reduction behaviour of Cr(VI) at PPy/Pt electrode was similar to PPy/GC electrode, Calibration graph was linear from l.0 ppm to 60.0 ppm. Slope factor and relative coefficient were 0.5mA/ppm and 0.923, respectively. But PPy/GC modified electrode had about 3 times higher sensitivity than PPy/Pt modified electrode. Reduction behaviour of Cu(II), As(IlI), Pb(II), and Cd(II) couldn't be seen at PPy/GC electrode,Its metals had not lnterfered with Cr (VI) determination.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.571-580
• /
• 2020

In this study, an experimental study on storage media for thermal energy storage system was conducted. For thermal energy storage medium, concrete has excellent thermal and mechanical properties and also has various advantages due to its low cost. In addition, the ultra-high strength concrete reinforced by steel fibers exhibits excellent durability against exposure to high temperatures due to its high toughness and high strength characteristics. Moreover, the high thermal conductivity of steel fibers has an advantageous effect on heat storage and heat dissipation. Therefore, to investigate the temperature distribution characteristics of ultra-high-strength concrete, concrete blocks were fabricated and a heating test was performed by applying high-temperature thermal cycles. The heat transfer pipe was buried in the center of the concrete block for heat transfer by heat fluid flow. In order to explore the temperature distribution characteristics according to different shapes of the heat transfer pipe, a round pipe and a longitudinal fin pipe were used. The temperature distribution at the differnent thermal cycles were analyzed, and the thermal energy and the cumulated thermal energy over time were calculated and analyzed for comparison based on test results.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.15 no.2
• /
• pp.86-96
• /
• 2010

The oxygen utilization rate (OUR) is one of the crucial parameters for ocean carbon cycling and climate models. However, parameterization of OUR in the East Sea (Sea of Japan) is yet to be established. We estimated the basin-specific OURs in the East Sea and fitted them with exponential functions with depth by using pCFC- 12 age and apparent oxygen utilization (AOU) measured in summer 1999. The estimated OURs are higher in the upper water column and decrease with depth, in general. The vertical distributions of the estimated OURs in the Western and Eastern Japan Basins (WJB & EJB) are very similar. The OURs in the Ulleung Basin (UB) varied greatly depending on whether the surface layer (0~200 m) data are included in the OUR estimate or not. Apparently, weaker oxygen consumption occurs in the deep layer of Yamato Basin (YB). The ranges of the OURs between 200 m and 2000 m at WJB, EJB, UB, and YB are 8.15~0.83, 8.11~0.68, 5.29~0.73, and 7.31~0.06 ${\mu}mol$ $kg^{-1}$ $yr^{-1}$, respectively. Consideration of the wintertime surface water oxygen disequilibrium condition in estimating the OUR will be necessary in the future study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.88-89
• /
• 2013

A variety of influenza A viruses from animal hosts are continuously prevalent throughout the world which cause human epidemics resulting millions of human infections and enormous industrial and economic damages. Thus, early diagnosis of such pathogen is of paramount importance for biomedical examination and public healthcare screening. To approach this issue, here we propose a fully integrated Rotary genetic analysis system, called Rotary Genetic Analyzer, for on-site detection of influenza A viruses with high speed. The Rotary Genetic Analyzer is made up of four parts including a disposable microchip, a servo motor for precise and high rate spinning of the chip, thermal blocks for temperature control, and a miniaturized optical fluorescence detector as shown Fig. 1. A thermal block made from duralumin is integrated with a film heater at the bottom and a resistance temperature detector (RTD) in the middle. For the efficient performance of RT-PCR, three thermal blocks are placed on the Rotary stage and the temperature of each block is corresponded to the thermal cycling, namely $95^{\circ}C$ (denature), $58^{\circ}C$ (annealing), and $72^{\circ}C$ (extension). Rotary RT-PCR was performed to amplify the target gene which was monitored by an optical fluorescent detector above the extension block. A disposable microdevice (10 cm diameter) consists of a solid-phase extraction based sample pretreatment unit, bead chamber, and 4 ${\mu}L$ of the PCR chamber as shown Fig. 2. The microchip is fabricated using a patterned polycarbonate (PC) sheet with 1 mm thickness and a PC film with 130 ${\mu}m$ thickness, which layers are thermally bonded at $138^{\circ}C$ using acetone vapour. Silicatreated microglass beads with 150~212 ${\mu}L$ diameter are introduced into the sample pretreatment chambers and held in place by weir structure for construction of solid-phase extraction system. Fig. 3 shows strobed images of sequential loading of three samples. Three samples were loaded into the reservoir simultaneously (Fig. 3A), then the influenza A H3N2 viral RNA sample was loaded at 5000 RPM for 10 sec (Fig. 3B). Washing buffer was followed at 5000 RPM for 5 min (Fig. 3C), and angular frequency was decreased to 100 RPM for siphon priming of PCR cocktail to the channel as shown in Figure 3D. Finally the PCR cocktail was loaded to the bead chamber at 2000 RPM for 10 sec, and then RPM was increased up to 5000 RPM for 1 min to obtain the as much as PCR cocktail containing the RNA template (Fig. 3E). In this system, the wastes from RNA samples and washing buffer were transported to the waste chamber, which is fully filled to the chamber with precise optimization. Then, the PCR cocktail was able to transport to the PCR chamber. Fig. 3F shows the final image of the sample pretreatment. PCR cocktail containing RNA template is successfully isolated from waste. To detect the influenza A H3N2 virus, the purified RNA with PCR cocktail in the PCR chamber was amplified by using performed the RNA capture on the proposed microdevice. The fluorescence images were described in Figure 4A at the 0, 40 cycles. The fluorescence signal (40 cycle) was drastically increased confirming the influenza A H3N2 virus. The real-time profiles were successfully obtained using the optical fluorescence detector as shown in Figure 4B. The Rotary PCR and off-chip PCR were compared with same amount of influenza A H3N2 virus. The Ct value of Rotary PCR was smaller than the off-chip PCR without contamination. The whole process of the sample pretreatment and RT-PCR could be accomplished in 30 min on the fully integrated Rotary Genetic Analyzer system. We have demonstrated a fully integrated and portable Rotary Genetic Analyzer for detection of the gene expression of influenza A virus, which has 'Sample-in-answer-out' capability including sample pretreatment, rotary amplification, and optical detection. Target gene amplification was real-time monitored using the integrated Rotary Genetic Analyzer system.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.209-213
• /
• 2019

Recently, demand for high energy density and long cycling stability of energy storage system has increased for application using with frequency regulation (F/R) in power grid. Supercapacitor have long lifetime and high charge and discharge rate, it is very adaptable to apply a frequency regulation in power grid. Supercapacitor can complement batteries to reduce the size and installation of batteries. Because their utilization in a system can potentially eliminate the need for short-term frequent replacement as required by batteries, hence, saving the resources invested in the upkeep of the whole system or extension of lifecycle of batteries in the long run of power grid. However, low energy density in supercapacitor is critical weakness to utilization for huge energy storage system of power grid. So, it is still far from being able to replace batteries and struggle in meeting the demand for a high energy density. But, today, LIC (Lithium Ion Capacitor) considered as an attractive structure to improve energy density much more than EDLC (Electric double layer capacitor) because LIC has high voltage range up to 3.8 V. But, many aspects of the electrochemical performance of LIC still need to be examined closely in order to apply for commercial use. In this study, in order to improve the capacitance of LIC related with energy density, we designed new method of pre-doping in anode electrode. The electrode in cathode were fabricated in dry room which has a relative humidity under 0.1% and constant electrode thickness over $100{\mu}m$ was manufactured for stable mechanical strength and anode doping. To minimize of contact resistance, fabricated electrode was conducted hot compression process from room temperature to $65^{\circ}C$. We designed various pre-doping method for LIC structure and analyzing the doping mechanism issues. Finally, we suggest new pre-doping method to improve the capacitance and electrochemical stability for LIC.

• Asia pacific journal of information systems
• /
• v.17 no.3
• /
• pp.105-130
• /
• 2007

Recently, there is a substantial interest in implementing Business Process Management System(BPMS) among enterprises with the purpose of business process innovation. BPMS redesigns and coordinates business processes in terms of both automated steps and human involvement in order to maximize the value of both involved people and systems. The reason why BPMS is getting attention from top managers is that it has the possibility to optimize the business processes by cycling the process of modeling, execution, monitoring, evaluation, and redesigning work processes. Thus, it has created high expectations about not only productivity improvement but also business process innovation. However. having an innovative nature, which is used for process innovation, BPMS implementation has great potential to stir up employee resistance. The analysis and the discussion about the prevention of the resistance against IS(Information Systems) is important because IS change the way people work and also alter the power structure within the organization, in general. The purpose of this study is to investigate factors that have an impact on the effective adoption of BPMS at the enterprise level. To find out these factors, this study considers two characteristics of BPMS: First. BPMS shares some characteristics with other enterprise-wide IS such as ERP. Second, it has special BPMS-specific characteristics. Due to the lack of previous research on BPMS adoption, interviews were carried out with IT-consultants and CIOs who conducted BPMS projects previously to find out BPMS-specific features that would make BPMS unique when compared to other enterprise-wide IS. As a result, the monitoring function was chosen as the main BPMS-specific factor. Thus, this paper reviewed studies both on enterprise-wide IS adoptions, which applied Technology Acceptance Model (TAM) and secondly on computer based monitoring to find out factors that would influence the employees' perception on the monitoring function of BPMS. Based on the literature review, the study suggested three factors that would have an impact on the employee's perception of the monitoring function: fairness of enterprise evaluation system, fairness of the boss, and self-efficacy of their work. Three factors that would impact the enterprise-wide IS adoption were also set: the shared belief in the benefit of BPMS, training, and communication. Then, these factors were integrated with TAM. Structural equation modeling was used to test hypotheses, out factors that would impact the employees' perception on the monitoring function of BPMS. Based on the literature review the study suggested three factors that would have an impact on the employee's perception of the monitoring function: fairness of enterprise evaluation system, fairness of the boss, and self-efficacy of their work. Three factors that would impact the enterprise-wide IS adoption were also set: the shared belief in the benefit of BPMS, training, and communication. Then, these factors were integrated with TAM. Structural equation modeling was used to test hypotheses. The data analysis results showed that two among three monitoring function related factors - enterprise evaluation system and fairness of the boss - were significant. This implies that employees would worry less about the BPMS implementation as long as they perceive the monitoring results will be used fairly for their performance evaluation. However, employees' high self-efficacy on their job was not a significant factor in their perception of the usefulness of BPMS. This is related to cases that showed employees resisted against the information systems because they automated their works (Markus, 1983). One specific case was an electronic company, where the accounting department workers were requested to redefine their job because their working processes were automated due to BPMS implementation.

• Journal of Korean Society of Forest Science
• /
• v.108 no.1
• /
• pp.40-49
• /
• 2019

Coarse woody debris (CWD), which is a component of the forest ecosystem, plays a major role in forest energy flow and nutrient cycling. In particular, CWD isolates carbon for a long time and is important in terms of slowing the rate of carbon released from the forest to the atmosphere. Therefore, this study measured the physiochemical characteristics and respiration rate ($R_{CWD}$) of CWD for Larix kaempferi and Pinus rigida in temperate forests in central Korea. In summer 2018, CWD samples from decay class (DC) I to IV were collected in the 14 forest stands. $R_{CWD}$ and physiochemical characteristics were measured using a closed chamber with a portable carbon dioxide sensor in the laboratory. In both species, as CWD decomposition progressed, the density ($D_{CWD}$) of the CWD decreased while the water content ($WC_{CWD}$) increased. Furthermore, the carbon concentrations did not significantly differ by DC, whereas the nitrogen concentration significantly increased and the C/N ratio decreased. The respiration rate of L. kaempferi CWD increased significantly up to DC IV, but for P. rigida it increased to DC II and then unchanged for DC II-IV. Accordingly, except for carbon concentration, all the measured characteristics showed a significant correlation with $R_{CWD}$. Multiple linear regression showed that $WC_{CWD}$ was the most influential factor on $R_{CWD}$. $WC_{CWD}$ affects $R_{CWD}$ by increasing microbial activity and is closely related to complex environmental factors such as temperature and light conditions. Therefore, it is necessary to study their correlation and estimate the time-series pattern of CWD moisture.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.17 no.2
• /
• pp.33-44
• /
• 2012

Transparent exopolymer particles (TEP) are formed by aggregation of polysaccharide products excreted by phytoplankton and have sticky character like gel. They play important role in the production of marine snow in water column. To study the distribution pattern of TEP concentration and its role in carbon cycle in the surface ocean, we measured pH, Total alkalinity (TA), and chlorophyll-a in addition to physical characteristics of seawater within the surface water column. TEP concentrations ranged from nearly undetectable values to $338{\mu}g\;Xeq\;l^{-1}$. They were considerably lower than previously reported values from costal sites, but showed similar values observed in other oceanic region during phytoplankton bloom periods. The spatial distribution of TEP concentrations were similar to those of chlorophyll-a, which indicate that the production of TEP were closely related to phytoplankton. Calculated total dissolved inorganic carbon ($TCO_2$) from the pH and TA was normalized to 35 psu of salinity ($NTCO_2$) and showed negative linear relationship with temperature. Biological drawdown of $NTCO_2$ ($NTCO_{2bio}$) was estimated from the difference between theoretical $NTCO_2$ values and observed $NTCO_2$. In the warm region located south of $40^{\circ}N$ along the $132.5^{\circ}N$ meridional lines, $NTCO_{2bio}$ showed negative value and TEP concentrations were high. This suggested that negative $NTCO_{2bio}$ may be attributed to the biological processes. At the stations located between 44 and $46^{\circ}N$, TEP concentrations showed high concentration at the chlorophyll-a maximum layer within the water column while they showed low concentration in the surface layer. Carbon content of TEP constituted about 40% of $NTCO_{2bio}$ at the chlorophylla maximum layer. In this study, we could not observe any positive and negative relationship between TEP concentration and $NTCO_2$ or pH. It is obvious that we should consider the importance of TEP in the biological carbon cycling processes within surface layer.

• Korean Journal of Ecology and Environment
• /
• v.38 no.1 s.110
• /
• pp.45-53
• /
• 2005

The environmental change of Yong-nup in Mt. Dae-Am, which is located at the northern part of Kangwon-Do, Korea, was assesed with peat sedimentary carbon and nitrogen isotope analysis. The surface layer of the peat (0 ${\sim}$ 5 cm) was 190 year BP, and the middle layers (30 ${\sim}$ 35 cm and 50 ${\sim}$ 55 cm) were 870 year BP and 1900 year BP, respectively. Bulk sedimentation rate was estimated to be about 0.4 mm $year^{-1}$ for 0 cm to 30 cm and 0.15 mm $year^{-1}$ for 35 cm to 50 cm. The $^{14}C$ age of the bottom sediment (75 ${\sim}$ 80 cm) collected and measured in this study was about 1900 year BP, although it was measured that the $^{14}C$ of the lowest bottom sediment in Yong-nup was 4105 ${\pm}$ 175 year BP (GX-23200). Since the $^{14}C$ ages for 50 ${\sim}$ 55 cm and 75 ${\sim}$ 80 cm layers were almost the same as 1890 ${\pm}$ 80 fear BP (NUTA 5364) and 1850 ${\pm}$ 90 year BP (NUTA 5462), respectively, we have estimated that the deep layers (55 ${\sim}$ 80 cm) in the high moor were the original forest soil. The low organic C and N contents in the deeper layers supported the inference. The sediment of 50 ${\sim}$ 55 cm layer contains much sandy material and showed very low organic content, suggesting the erosion (flooding) from the surrounding area. In this context, the Yong-nup, high moor, of Mt. Dae-Am, might have developed to the sampling site at about 1900 year BP. The ${\delta}^{13}C$ values of organic carbon and the ${\delta}^{15}N$ values of total nitrogen in the peat sediments fluctuated with the depths. The profile of ${\delta}^{13}C$ may indicate that the Yong-nup of Mt. Dae-Am have experienced the dry-wet and cool-warm period cycles during the development of the high moor. The ${\delta}^{15}N$ may indicate that the nitrogen cycling in the Yong-nup have changed from the closed (regeneration depending) system to the open (rain $NO_3\;^-$ and $N_2$ fixation depending) system during the development of the high moor.

• Journal of Korean Academy of Nursing
• /
• v.28 no.4
• /
• pp.1047-1059
• /
• 1998

Senile Dementia is one of the dispositional mental disorder which has been known to the world since Hippocratic age. It has become a wide-spread social problem all over the world because of chronic disease processes and the demands of dependent care for several years as well as improbability of treatment of it at the causal level. Essentially, life styles of the older generation differ from those of the younger generation. While the fomer is used to the patriarchal system and the spirit of filial piet and respect, the latter is pragmatized and individualized under the effects of the Western material civilization. These differences between the two generations cause conflict between family members. In particular, the pain and conflict of care-givers who take care of a totally dependent dementia patient not only is inciting to the collapse of the family union, but is expanding into a serious social problem. According to this practical difficulty, this study has tried to compare dementia care-givers' experiences inter-culturally and to help set up more proper nursing interventions, describing and explaining them through ethnographies by participant observation and in-depth interviews that enable seeing them in a more close, honest and certain way. It also tries to provide a theoetical model of nusing care for dementia patients which is proper to Korean culture. This study is composed of 12 participants (4 males, 8 females) whose ages range from 37-71 years. The relations of patients are 5 spouses(3 husbands, 2 wives), 4 daughters-in-law, 2 daughters, and 1 son-in-law. The following are the care-givers' meaning of experiences that results of the study shows. The first is "psychological conflict". It contains the minds of getting angry, reproaching, being driven to dispair, blaming oneself, giving up lives, and being afraid, hopeless, and resigned. The second is "physical, social and psychological pressure" . At this stage, care-givers are shown to be under stress of both body and soul for the lack of freedom and tiredness. They also feel constraint because they hardly cope with the care and live through others' eyes. The third is "isolation". It makes the relationship of patient care-giver to be estranged, without understanding each other. They, also, experience indifference such as being upset and left alone. The forth is "acceptance" They gradually have compassion, bear up and then adapt themselves to the circumstances they are in. The fifth is "love". Now they learn to reward the other with love. It is also shown that this stage contains the process of winning others' recognition. The final is "hope". In this stage they really want situations to go smoothly and hope everything will be O.K. These consequences enable us to summarize the principles of cue experience such as, in the early stage, negative response such as physical·psychological confusion, pain and conflict are primary. Then the stage of acceptance emerges. It is an initial positive response phase when care-givers may admit their situations. As time passes by a positive response stage emerges. At last they have love and hope. Three stages we noted above : however, there are never consistent situations. Rather it gradually comes into the stage of acceptance, repeating continuous conflict, pressure and isolation. If any interest and understanding of families or the support of surrounding society lack, it will again be converted to negative responses sooner or later. Otherwise, positive responses like hope and love can be encouraged if the family and the surroundings give active aids and understanding. After all, the principles of dementia care experiences neither stay at any stage, nor develop from negative stages to positive stages steadily. They are cycling systems in which negative responses and positive responses are constantly being converted. I would like to suggest the following based on the above conclusions : First, the systematic and planned education of dementia should be performed in order to enhance public relations. Second, a special medical treatment center which deals with dementia, under government's charge, should be managed. Third, the various studies approaching dementia care experiences result in the development of more reasonable and useful nursing guidelines.