• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1201-1207
• /
• 2010

본 연구에서는 마이크로 시험편에 대하여 하중제어 인장-인장의 피로시험이 가능한 피로시험기를 개발하였다. 전자기식 액추에이터를 이용하였으며, 이 시험기를 이용하여 인장시험 뿐만 아니라 넓은 주파수 영역에서의 피로시험이 가능하다. 또한 피로시험중에도 고해상도로 마이크로 시험편의 되풀이 변형률을 측정할 수 있는 간섭변위계를 사용하였다. 피로시험기와 변위계는 안정적이고 그 응답속도도 매우 빨라서, 피로시험중에도 연속적으로 변위를 측정할 수 있다.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.41-48
• /
• 1984

Recrystallization technique was applied to analyze plastic strain at the notch tip of coarse grain HAZ in mild steel (SB 41) and high strength steel (SA 588). The notch tip of specimen was deformed by three point bending. Accumulated displacement (Crack Opening Displacement ${delta}t$) by the monotonic and cyclic loading under room temperature and hot strain embrittlement temperature ($250^{\circ}C$) was 0~1.0mm. Recrystallization heat treatment conditions were $650^{circ}C{ imes}3hr$ for SB 41 and $700^{circ}C{ imes}3hr$ for SA 588. The experimental results obtained were as follows ; 1) Distribution of the effective plastic strain at plastic zone was appeared by the function of crack opening displacement, and plastic zone or the effective plastic strain increased with crack opening displacement. 2) Plastic strain at notch tip of HAZ due to accumulated hot strain calculated as follows. .epsilon. over bar $_{p}$ = .epsilon. over bar $_{cr}$ (x/ $R_{x}$ ) $^{m}$ (m=0.25) 3) Work hardending ratio of notch tip for hot strain was linearly increased with .epsilon. over bar $_{max}$ and dependent upon the material types.s.

• 한국지반공학회논문집
• /
• 제31권2호
• /
• pp.47-63
• /
• 2015

본 연구에서는 풍화토에 근입된 현장타설말뚝을 대상으로 수평 반복하중에 대한 말뚝-지반의 상호거동을 파악하기 위하여 현장타설말뚝 재하시험 및 3차원 유한요소 해석을 수행하였다. 현장재하시험은 국내에 널리 분포하고 있는 풍화토 지반에 근입된 현장타설말뚝을 재하시험 대상으로 하였다. 반복하중의 방향을 달리하여 일방향과 양방향으로 반복하중을 재하 하였으며, 반복하중의 방향에 따른 시험말뚝의 수평변위 및 휨모멘트를 분석하였다. 또한, 지반 물성이 말뚝-지반의 상호거동에 미치는 영향과 반복하중의 횟수, 방향 등, 하중특성 인자들의 영향 정도를 살펴보기 위하여 3차원 유한요소 모델링 및 해석을 수행하였으며, 국내 외에서 수행된 현장재하시험의 사례들 및 기존에 제안된 경험적 반복하중 p-y 곡선 함수들과 비교 분석함으로서 3차원 유한요소 모델링의 타당성을 확인하였다. 3차원 유한요소해석 결과, 풍화토에 근입된 현장타설말뚝에 작용하는 반복하중의 방향성을 고려할 수 있는 쌍곡선 형태의 p-y 곡선 함수식을 제안하였다. 또한 쌍곡선 형태의 정적하중 p-y 곡선 함수식에 반복하중에 의한 지반반력계수와 지반의 극한저항력의 감소 효과를 동시에 고려할 수 있는 감소계수를 도출하여, 말뚝의 변위와 지반의 극한 저항력의 관계를 하나의 함수식으로 표현하였다. 사질토에 근입된 말뚝의 반복하중 재하시험 사례들을 이용하여 결과를 비교 분석한 결과, 제안된 p-y 곡선 함수는 현장 실측치와 비교적 잘 일치하였으며, 기존의 경험적 반복하중 p-y 곡선 함수보다 말뚝-지반의 수평거동 특성을 더 적절히 예측함을 알 수 있었다.

• 한국지진공학회논문집
• /
• 제17권5호
• /
• pp.227-235
• /
• 2013

Friction energy dissipative devices have been increasingly implemented as structural seismic damage protecting systems due to their excellent seismic energy dissipating capacity and high stiffness. This study develops rotational friction energy dissipative devices and verifies experimentally their cyclic response. Based on the understanding of the differences between the traditional linear-motion friction behavior and the rotational friction behavior, the configuration of the frictional surface was determined by investigating the characteristics of the micro-friction behavior. The friction surface suggested in this paper consists of brake-lining pads and stainless steel sheets and is normally stressed by high-strength bolts. Based upon these frictional characteristics of the selected interface, the rotational friction energy dissipative devices were developed. Bolt torque-bearing force tests, rotational friction tests of the suggested friction interfaces were carried out to identify their frictional behavior. Test results show that the bearing force is almost linearly proportional to the applied bolt torque and presents stable cyclic response regardless of the experimental parameters selected this testing program. Finally, cyclic tests of the rotational friction energy dissipative devices were performed to find out their structural characteristics and to confirm their stable cyclic response. The developed friction energy dissipative devices present very stable cyclic response and meet the requirements for displacement-dependent energy dissipative devices prescribed in ASCE/SEI 7-10.

• 한국공간구조학회논문집
• /
• 제6권4호
• /
• pp.53-61
• /
• 2006

본 연구에서는 임의의 반복하중 작용시 강구조물에 발생하는 대변형 및 반복소성거동을 정확히 예측하기 위하여 유한변위이론과 반복소성이력모델을 적용한 3차원 탄소성 유한요소 해석기법을 개발하였다. 반복소성이력모델은 강재의 단조재하실험 및 반복하중실험 결과에 기초하여 정식화되었다. 개발된 해석기법의 정도는 Bilinear모델 및 미소변위이론을 적용한 해석기법 및 실험결과와 비교하여 검증하였다. 본 연구에서 개발한 유한변위이론과 반복소성이력모델을 적용한 3차원 유한요소 해석기법이 임의의 반복하중을 받는 원형강교각의 대변형 및 반복소성거동을 정확히 예측할 수 있음을 알 수 있었다.

• Steel and Composite Structures
• /
• 제26권4호
• /
• pp.439-452
• /
• 2018

This paper presents experimental and numerical study on buckling behaviors and hysteretic performance of Class 1 H-shaped steel beam subjected to cyclic pure bending within the scope of ultra-low cycle fatigue (ULCF). A loading device was designed to achieve the pure bending loading condition and 4 H-shaped specimens with a small width-to-thickness ratio were tested under 4 different loading histories. The emphasis of this work is on the impacts induced by local buckling and subsequent ductile fracture. The experimental and numerical results indicate that the specimen failure is mainly induced by elasto-plastic local buckling, and is closely correlated with the plastic straining history. Compared with monotonic loading, the elasto-plastic local buckling can occur at a much smaller displacement amplitude due to a number of preceding plastic reversals with relative small strain amplitudes, which is mainly correlated with decreasing tangent modulus of the material under cyclic straining. Ductile fracture is found to be a secondary factor leading to deterioration of the load-carrying capacity. In addition, a new ULCF life evaluation method is proposed for the specimens using the concept of energy decomposition, where the cumulative plastic energy is classified into two categories as isotropic hardening and kinematic hardening correlated. A linear correlation between the two energies is found and formulated, which compares well with the experimental results.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.232-239
• /
• 2005

Recently geosynthetics that can be constructed on soft ground have been used for reinforcement and separation in various ways. Through laboratory model tests and numerical analysis, in this study, estimated the suitability of cable elements and appropriate input factors considering loading effect in modeling of geosynthetics. First, in laboratory model tests, geosynthetics were constructed on the clay, and covered with the thickness, 7.5cm of sand mat. And then static and dynamic model tests were performed measuring loading, settlement, ground lateral displacement, and displacements of geosynthetics, but, for cyclic loading, bearing capacity increased linearly with stiff slop because cyclic loading with constant cyclic pressure compacted the ground. Numerical analysis were performed with FLAC 4.0 2D using Mohr-Coulomb and Modified Cam-Clay models, and they compared with the results of model tests. Cable elements of FLAC in modeling geosynthetics couldn't consider the characteristics of geosynthetics that increase shear strength between geosynthetics and clay according to the loading increase. Therefore, in this study, appropriate equation that can consider loading effects in Cable elements was proposed by Case Study.

• 대한기계학회논문집A
• /
• 제31권9호
• /
• pp.903-909
• /
• 2007

A fatigue capsule is one of the special capsules to investigate the fatigue characteristics of the nuclear materials during an irradiation test in a research reactor, HANARO. In this study, the performance test and the preliminary fatigue test results by using a cyclic load device newly developed for a fatigue capsule are described. In order to obtain the characteristics such as a realization and a controllability of the periodic wave shape and the relationship between the pressure and the load, a spring and rigid bar specimens are used. The fatigue test for the 316L stainless steel specimen with 1.8mm in diameter and 12.5mm in gage length is also performed under the same conditions as the temperature($550^{\circ}C$) of the specimen during irradiation tests. As a result of the test, the fracture of the specimen occurs at a total of 70,120 cycles(about 12 days), and the displacement in this case is 2.02 mm. It is expected that these results will be used for determining test conditions and a comparison of the in-pile fatigue test results.

• Structural Engineering and Mechanics
• /
• 제27권6호
• /
• pp.697-711
• /
• 2007

Though extensive research has been carried out for the ultimate strength of steel reinforced concrete (SRC) members under static and cyclic load, there was only limited information on the applied analysis models. Modeling of the inelastic response of SRC members can be accomplished by using a microcosmic model. However, generally used microcosmic model, which usually contains a group of parameters, is too complicated to apply in the nonlinear structural computation for large whole buildings. The intent of this paper is to develop an effective modeling approach for the reliable prediction of the inelastic response of SRC columns. Firstly, five SRC columns were tested under cyclic static load and constant axial force. Based on the experimental results, normalized trilinear skeleton curves were then put forward. Theoretical equation of normalizing point (ultimate strength point) was built up according to the load-bearing mechanism of RC columns and verified by the 5 specimens in this test and 14 SRC columns from parallel tests. Since no obvious strength deterioration and pinch effect were observed from the load-displacement curve, hysteresis rule considering only stiffness degradation was proposed through regression analysis. Compared with the experimental results, the applied analysis model is so reasonable to capture the overall cyclic response of SRC columns that it can be easily used in both static and dynamic analysis of the whole SRC structural systems.

• 한국지반공학회논문집
• /
• 제21권5호
• /
• pp.179-186
• /
• 2005

실내 모형실험으로 정,반복하중 재하 실험을 실시하여 하중과 침하, 지중 측방변위, 토목섬유 변위 등을 측정한 결과 지반과의 마찰과 토목섬유 인장력의 영향으로 전반적으로 지반의 변위가 줄고 지지력이 증가하였다. 또한 Mohr-coulomb 및 수정Mohr-Coulomb 모델들과 FLAC 4.0 2D을 사용하여 수치해석을 실시하였고 실내 모형 실험결과와 비교하였다. 기존식들은 토목섬유 모델링시 FLAC의 케이블 요소는 하중증가에 따른 전단강도를 증가되는 특성을 고려할수 없었기 때문에 실험 결과치와 상이하게 나타났다. 따라서 본 연구에서는 반복적인 학습으로 상재 하중의 영향을 고려한 케이블 구성요소의 적절한 식을 제시하였다.