• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.286-293
• /
• 2005

An interpretation on the solid circulation characteristics in a fluidized-bed process has been carried out as a first step to simulate the dry entrained-bed absorption and bubbling-bed regeneration system for $CO_2$ removal from flue gas. A particle population balance has been developed to determine the solid flow rates and particle size distributions in the process. Effects of principal process parameters have been discussed in a laboratory scale process (absorption column: 25 mm i.d., 6 m in height; regeneration column: 0.1 m i.d., 1.2 m in height). The particle size distributions in absorption and regeneration columns were nearly the same. As gas velocity or static bed height in the absorption column increased, soild circulation rate and feed rate of fresh sorbent increased, however, mean particle diameter decreased in the absorption column. As cut diameter of the cyclone of the absorption column increased, solid circulation rate decreased, whereas feed rate of fresh sorbent and mean particle diameter in the absorption column increased. As attrition coefficient of sorbent particle increased, solid circulation rate and feed rate of fresh sorbent increased but mean particle diameter in the absorption column decreased.

• Journal of Korean Society of Forest Science
• /
• v.108 no.3
• /
• pp.322-328
• /
• 2019

The purpose of this study was to provide basic data for maintenance and repair of the forest road surfaces using the light drop weight test (LDWT), density test, and grain size analysis at four sites in Yeongyang-gun Mt. (2011y, 2014y, 2016y, and 2017y). In terms of the density test results, the opening density in 2011 was the highest at $2.0694g/cm^3$, and the opening density in 2017 was the lowest at $1.7443g/cm^3$. The grain size analysis showed that the proportion of large aggregates was highest at the opening in 2017, and the proportion of large aggregates decreased with the delay of opening date. From the LDWT results, $E_{vd}$ (the dynamic deformation coefficient) of the 2011y forest road was $35.7MN/m^2$, 2014y was $30.5MN/m^2$, 2016y was $28.6MN/m^2$, and 2017y was $23.5MN/m^2$. The $E_{vd}$ value for the oldest forests opened with the 2011y forest road was the highest, the average $E_{vd}$ value of the center portion was $21.45MN/m^2$, the average $E_{vd}$ value of the wheel portion of the banking part was $31.31MN/m^2$, and the average $E_{vd}$ value of the wheel portion of the cut part was $36.71MN/m^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.382-389
• /
• 2019

A novel folding process is proposed using a repeated cold-die forging and annealing to form a sterling silver ring. Sterling silver plate was cut into a doughnut shape, and lattices with 0.43-mm line-width were imprinted on it. The sample was folded by forging using dies with slopes of $45^{\circ}$, $60^{\circ}$, and $75^{\circ}$ and annealing. For comparison, samples were also fabricated without annealing. Strain was identified by measuring the length of lattices. Vernier calipers, a Vickers hardness tester, an optical microscope, and a UV-VIS colorimeter were used to determine the size, hardness, microstructure, and body color. Without annealing, cracks occurred. However, successful deformation was possible when annealing was used. The results of macro strain measurements show that the outer diameter and width decreased, while the inner diameter and thickness increased after the final process. The maximum strain was increased 0.128 toward the parallel direction. The Vickers hardness decreased after annealing and increased after the folding process. The microstructure results showed that the grain size increased after annealing but decreased after folding. The color difference based on the Lab index was under 10 for all processes. Eventually, a doughnut-shaped silver plate was successfully deformed into a ring shape by the folding process.

• Journal of Gastric Cancer
• /
• v.4 no.4
• /
• pp.235-241
• /
• 2004

Purpose: This study was performed to evaluate the effectiveness of the serum tumor markers CEA, CA 19-9, and CA 72-4 in monitoring the recurrence of gastric cancer and in its preoperative assessment. Materials and Methods: Two hundred fifty-five patients who underwent potentially curative surgery during period from January 1995 to December 2000 at the Department of Surgery were assessed. Serum samples were obtained preoperatively, 2 weeks after the surgery, and at 6-month intervals. The cut-off levels were established as 5 ng/ml for CEA, 36 U/ml for CA 19-9, and 4 U/ml for CA 72-4. The tumor stage was described according to the 5th edition of the Union Internationale Contra la Cancer (UICC) TNM classification in 1997. Results: The preoperative positivities were $10.5\%$ for CEA, $9.7\%$ for CA 19-9, and $12.4\%$ for CA 72-4. The serum levels of the three tumor markers decreased after curative surgery. The preoperative serum levels of the three tumor markers were significantly related to the depth of invasion, the tumor size, lymph-node metastasis, the pathologic stage, and recurrence, except that CEA was not associated with tumor size. The marker sensitivities in recurrent cases were $43.3\%$ for CEA, $\%41.8$ for CA 19-9, and $50.0\%$ for CA 72-4, and the marker specificities were $85.1\%$ for CEA, $96.8\%$ for CA 19-9, and $87.8\%$ for CA 72-4. Conclusion: The preoperative serum levels of CEA, CA 19-9, and CA 72-4 are not useful for the initial diagnosis of gastric cancer because of their low positivity. However, we should consider their relationship with depth of invasion, lymph-node metastasis, tumor size, pathologic stage, and recurrence. Also, the follow-up levels of the three markers have a statistical relationship with recurrence of gastric cancer even though their sensitivities are low.

• Economic and Environmental Geology
• /
• v.34 no.6
• /
• pp.627-648
• /
• 2001

At least two distinct types of layering are present in the middle zone of the Skaergaard intrusion; alternating plagioclase-rich and pyroxene-rich, macro-rhythmic layers, and smaller scale, modally-graded, rhythmic layers. The macro-rhythmic layers are ubiquitous in the middle zone of the Layered Series, but are not observed in the lower and upper zone of the Layered Series or in the wall or roof tories of the intrusion. They range from 0.3 to 17.3 m in thickness, have sharp upper and lower boundaries, and can be traced laterally for over 2 ]fm in outcrop. Although individual macrorhythmic layers are not internally graded, many contain smaller-scale, modally-graded layers. Modally-graded. rhythmic layers are a common feature of the Layered Series but are not abundant in either the Upper Border Series or the Marginal Border Series. They range in thickness from 1 to 50 cm and can be traced laterally in outcrop for up to 100 m. Their lateral termination ranges from abrupt to gradational, and they are often associated with cut and fill structures and crossbedding suggestive of current activity. They are characterized by sharp lower and gradational upper contacts, and by strong intra-layer modal grading with olivine, ilmenite, and magnetite concentrated at the base, pyroxene concentrated above the base, and plagioclase concentrated at the top. The layers are also grain-size graded with the maximum size for each phase occurring at the horizon in the layer where the phase is most abundant. Modally-graded, rhythmic layers in the middle zone of the Layered Series occur within both plagioclase-rich and pyroxene-rich macro-rhythmic layers.

• Journal of Gastric Cancer
• /
• v.6 no.4
• /
• pp.244-249
• /
• 2006

Purpose: Tumor size has been reported to be one of the prognostic factors in the preoperative setting and 8 cm has been confirmed as a cut-off value for large gastric tumors with respect to postoperative complications. The aim of this study was to investigate the clinicopathologic features and the prognosis in patients with tumors larger than 8 cm in diameter. Materials and Methods: We retrospectively studied 2,260 patients with gastric cancer who underwent a gastrectomy from 1983 to 2001 at the Department of Surgery, Korea University College of Medicine. For a comparative analysis we divided the cases into the large and the small groups according to tumor size. The clinicopathological factors associated with large gastric tumors were analyzed by using univariate and multivariate analyses. To determine which variables were independent prognostic factors for overall survival, we applied the Cox proportional hazards model and we used P<0.05 as the cutoff value for statistical significance. Results: Univariate and multivariate analyses disclosed that tumor location (P<0.001), resection type (P<0.001), curability (P<0.001), depth of invasion (P<0.001), number of metastatic lymph nodes (P<0.001), differentiation (P<0.001) and combined resection (P<0.001) were significantly different between the two groups. The independent factors for survival identified by using the Cox proportional hazards model for large gastric tumors were nodal status (P<0.001), curative resection (P<0.001), depth of invasion (P=0.010), type of resection (P=0.018) and age (P=0.033). Conclusion: Large gastric tumors showed more aggressive local findings than their smaller counterparts. In patients with large gastric tumors, a curative resection was the most important factor for the prognosis. Therefore, we suggest that every effort should be made to do a curative gastrectomy and an accurate preoperative examination. (J Korean Gastric Cancer Assoc 2006;6:244-249)

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.3
• /
• pp.543-560
• /
• 2018

With the increased development in downtown underground space facilities that vertically cross under a railway at a shallow depth, the demand for non-open cut method is increasing. However, most construction sites still adopt the pipe roof method, where medium and large diameter steel pipes are pressed in to form a roof, enabling excavation of the inside space. Among the many factors that influence the loosening region and loads that occur while pressing in steel pipes, the size of the pipe has the largest impact, and this factor may correspond to the magnitude of load applied to the underground structure inside the steel pipe roof. The super equilibrium method (SEM) has been developed to minimize ground disturbance and loosening load, and uses small diameter pipes of approximately 114 mm instead of conventional medium and large diameter pipes. This small diameter steel pipe is called an SEM pile. After SEM piles are pressed in and the grouting reinforcement is constructed, a crossing structure is pressed in by using a hydraulic jack without ground subsidence or heaving. The SEM pile, which plays the role of timbering, is a fore-poling pile of approximately 5 m length that prevents ground collapse and supports surface load during excavation of toe part. The loosening region should be adequately calculated to estimate the spacing and construction length of the piles and stiffness of members. In this paper, we conducted a comparative analysis of calculations of loosening load that occurs during the press-in of SEM pile to obtain an optimal design of SEM. We analyzed the influence of factors in main theoretical and empirical formulas applied for calculating loosening regions, and carried out FEM analysis to see an appropriate loosening load to the SEM pile. In order to estimate the soil loosening caused by actual SEM-pile indentation and excavation, a steel pipe indentation reduction model test was conducted. Soil subsidence and soil loosening were investigated quantitatively according to soil/steel pipe (H/D).

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.11
• /
• pp.1619-1637
• /
• 2000

A review was undertaken to obtain information on the range of beak-trimming methods available or under development. Beak-trimming of commercial layer replacement pullets is a common yet critical management tool that can affect the performance for the life of the flock. The most obvious advantage of beak-trimming is a reduction in cannibalism although the extent of the reduction in cannibalism depends on the strain, season, and type of housing, flock health and other factors. Beak-trimming also improves feed conversion by reducing food wastage. A further advantage of beak-trimming is a reduction in the chronic stress associated with dominance interactions in the flock. Beak-trimming of birds at 7-10 days is favoured by Industry but research over last 10 years has shown that beak-trimming at day-old causes the least stress on birds and efforts are needed to encourage Industry to adopt the practice of beak-trimming birds at day-old. Proper beak-trimming can result in greatly improved layer performance but improper beak-trimming can ruin an other wise good flock of hens. Re-trimming is practiced in most flocks, although there are some flocks that only need one trimming. Given the continuing welfare scrutiny of using a hot blade to cut the beak, attempts have been made to develop more welfare friendly methods of beak-trimming. Despite the developments in design of hot blade beak-trimmers the process has remained largely unchanged. That is, a red-hot blade cuts and cauterises the beak. The variables in the process are blade temperature, cauterisation time, operator ability, severity of trimming, age of trimming, strain of bird and beak length. This method of beak-trimming is still overwhelmingly favoured in Industry and there appears to be no other alternative procedures that are more effective. Sharp secateurs have been used trim the upper beak of both layers and turkeys. Bleeding from the upper mandible ceases shortly after the operation, and despite the regrowth of the beak a reduction of cannibalism has been reported. Very few differences have been noted between behaviour and production of the hot blade and cold blade cut chickens. This method has not been used on a large scale in Industry. There are anecdotal reports of cannibalism outbreaks in birds with regrown beaks. A robotic beak-trimming machine was developed in France, which permitted simultaneous, automated beak-trimming and vaccination of day-old chicks of up to 4,500 chickens per hour. Use of the machine was not successful because if the chicks were not loaded correctly they could drop off the line, receive excessive beak-trimming or very light trimming. Robotic beak-trimming was not effective if there was a variation in the weight or size of chickens. Capsaicin can cause degeneration of sensory nerves in mammals and decreases the rate of beak regrowth by its action on the sensory nerves. Capsaicin is a cheap, non-toxic substance that can be readily applied at the time of less severe beak-trimming. It suffers the disadvantage of causing an extreme burning sensation in operators who come in contact with the substance during its application to the bird. Methods of applying the substance to minimise the risk to operators of coming in contact with capsaicin need to be explored. A method was reported which cuts the beaks with a laser beam in day-old chickens. No details were provided on the type of laser used, or the severity of beak-trimming, but by 16 weeks the beaks of laser trimmed birds resembled the untrimmed beaks, but without the bill tip. Feather pecking and cannibalism during the laying period were highest among the laser trimmed hens. Currently laser machines are available that are transportable and research to investigate the effectiveness of beak-trimming using ablasive and coagulative lasers used in human medicine should be explored. Liquid nitrogen was used to declaw emu toes but was not effective. There was regrowth of the claws and the time and cost involved in the procedure limit the potential of using this process to beak-trim birds.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.94-100
• /
• 2011

Purpose: Basal/Acetazolamide-challenged brain perfusion SPECT is very useful to assess cerebral perfusion and vascular reserve. However, as there is a trade off between sensitivity and spatial resolution in the selection of collimator, the selection of optimal collimator is crucial. In this study, we examined three collimators to select optimal one for 1-day brain perfusion SPECT. Materials and Methods: Three collimators, low energy high resolution-parallel beam (LEHR-par), ultra resolution-fan beam (LEUR-fan) and super fine-fan beam (LESFR-fan), were tested for 1-day imaging using Triad XLT 9 (TRIONIX). The SPECT images of Hoffman 3D brain phantom filled with 99mTc of 170 MBq and a normal volunteer were acquired with a protocol of 50 kcts/frame and detector rotation of 3 degree. Filterd backprojection (FBP) reconstruction with Butterworth filter (cut off frequencies, 0.3 to 0.5) was performed. The quantitative and qualitative assessments for three collimators were performed. Results: The blind tests showed that LESFR-fan provided the best image quality for Hoffman brain phantom and the volunteer. However, images for all the collimator were evaluated as 'acceptable'. On the other hand, in order to meet the equivalent signal-to-noise ratio (SNR), total acquisition time or radioactivity dose for LESFR-fan must have been increased up to almost twice of that for LEUR-fan and LEHR-par. The volunteer test indicated that total acquisition time could be reduced approximately by 10 to 14 min in clinical practice using LEUR-fan and LEHR-par without significant loss on image quality, in comparison with LESFR-fan. Conclusion: Although LESFR-fan provides the best image quality, it requires significantly more acquisition time than LEUR-fan and LEHR-par to provide reasonable SNR. Since there is no significant clinical difference between three collimators, LEUR-fan and LEHR-par can be recommended as optimal collimators for 1-day brain perfusion imaging with respect to image quality and SNR.

• Clean Technology
• /
• v.18 no.4
• /
• pp.390-397
• /
• 2012

Removal characteristics of lead-contaminated soil at the military shooting range located in the Changwon city were studied experimentally using soil washing process. As a washing solution, hydrogen chloride (HCl) concentrations of 0.001, 0.01, 0.1 and 0.2 N were used, and soil : solution ratios were 1 : 2, 1 : 3, 1 : 4, and 1 : 5. Particle diameter of contaminated soil of 4-0.075 mm, and washing period of 5, 10, 15, 20, 30, 60, and 120 min were used as operating parameters. The optimum concentration of HCl solution was 0.1 N (56.3% of Pb removal efficiency) with 15 minutes operation period in views of economics, and the optimum soil : solution ratio was determined as 1 g : 3 mL for 69.7% of Pb removal efficiency with 0.1 N HCl and 15 minutes washing period. As washing period increased, removal efficiency was increased until 20 min of the removal efficiency of 75.3%, and then almost stable. Pb removal efficiency in soil particle diameters of 0.075 mm or more was ranged from 77.0% to 82.0%, but it was decreased to 52.8% in diameter of less than 0.075 mm. Therefore, the optimum cut-off size of the soil particle diameter was found less than 0.075 mm. Combined HCl solution and ultrasonic washing method showed better removal efficiency compared to only water or HCl washing method for particle sizes above 0.075 mm.