• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.237-243
• /
• 2002

단상 위상각제어시스템의 경우 제어기의 구조상의 단순함과 저가격화로 인해 많은 노이즈가 발생함에도 불구하고 트라이액 교류 위상각제어기를 속도제어기로 사용하고 있다. 시판되는 진공청소기의 경우 트라이액의 위상각을 조절하여 속도를 제어하고 있는데 고조파전류의 발생을 최소화로 하기 위해서 속도의 선형성을 고려하지는 않고 제작하고 있는 경우가 대부분이다. 본 논문에서는 진공청소기용 위상각 제어기에 파라미터 추정에 의한 실제작 시스템으로 고조파가 많이 발생되는 특정 트라이액 트리거 위상각에서도 고조파전류가 효과적으로 감소되고 부수적으로 지연각이 없어지는 고조파전류 감쇠용 위상제어기의 설계 및 제작하여 실험을 통해 입증하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.289-289
• /
• 2008

We investigated the operational characteristics of the separated three-phase flux-lock type superconducting fault current limiter (SFCL). The single-phase lock type SFCL consist of two coils, which are wound in parallel through an iron core. The high-$T_c$ superconducting(HSTC) thin film connected in series with secondary coil. The separated three-phase flux-lock type SFCL consist of three single-phase flux-lock type SFCL. In a normal condition, the SFCL is not operate. When a fault occurs, the current of a HSTC thin film exceeds its critical current by fault current, the resistance of the HSTC thin film generated. Therefore fault current was limited by SFCL. The separated three-phase flux-lock type SFCL are operated in fault condition such as the the single line-to-ground fault, the double line-to-ground fault and the triple line-to-ground fault. The experimental results, the SFCL operational characteristics was dependent on fault condition.

• 전기학회논문지P
• /
• 제63권1호
• /
• pp.12-18
• /
• 2014

This paper analyzes how to calculate the three phase short circuit current calculation procedures used in the IEC 60909 short circuit. It presented the new procedure of the fault current for the interrupting capacity of the circuit breaker. This procedure is applied to the future power system and calculates the fault current. Power demands are increased because of the growth of the economy for this reason, the fault current of the power system is largely increased and the fault current procedure for the proper interrupting capacity calculation of the existing or the new circuit breaker is essential. How to calculate the three phase short circuit current for ac electrical system and select the high voltage and low voltage circuit breaker based on IEC 60909 standards.

• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.262-267
• /
• 2014

This study describes that light flicker of LED lamp is improved by placing an AC-powered LED block in each phase of three-phase AC power. Rectified current is considered as an instantaneous luminous flux because the current flowing through the LED block is proportional to the amount of light emitted by the LED block. Percent flicker is calculated simply by modeling the rectified current flowing through the LED block to a triangular wave current. Percent flicker is 100% in single-phase AC powered LED lamp. Percent flicker of the same level as that in an incandescent lamp (6%~14%) is however, achieved if light emission starts before $40^{\circ}$ in each voltage phase of three-phase AC power.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.162-168
• /
• 2008

In this paper, we analyzed the heat transfer phenomenon and the reset current variation of PRAM device with thickness of phase change material using the 3-D finite element analysis tool. From the simulation, Joule's heat was generated at the contact surface of phase change material and bottom electrode of PRAM. As the thickness of phase change material was decreased, the reset current was highly increased. In case thickness of phase change material thin film was $200\;{\AA}$, heat increased through top electrode and reset current caused by phase transition highly increased. And as thermal conductivity of top electrode decreased, temperature of unit memory cell was increased.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.149-151
• /
• 2005

This paper deals with the novel control algorithm of single-phase hybrid active power filter for the compensation of harmonic current components in nonlinear R-L load with passive active power filters. To construct two-axes coordinate, an imaginary second phase was made by giving time delay to line current. In this proposed method, the new signal, which was the delayed through the filtering by the phase-delay property of low-pass filter, is used as the secondary phase. Because two phases have different phase, instantaneous calculation of harmonic current is possible. In this paper, a reference voltage is created by multiplying gain of filter by compensation current using the rotating reference frames that synchronizes with source-frequency, not applying to instantaneous reactive power theory which has been used with the existing fixed reference frames. This paper shows the experimental results, which provide a high accuracy and extremely fast response of single-phase hybrid active Bower filter under the operation with the proposed control method.

• 전력전자학회논문지
• /
• 제20권4호
• /
• pp.356-362
• /
• 2015

This paper presents a current control strategy in the synchronous reference frame for a single-phase PWM converter, which ensures sinusoidal input current control under the distorted source voltage and frequency condition. Given that the distorted source voltage distorts the phase angle for PWM converter control, the input current contains the same harmonics as the source voltage. Aside from the distorted voltage, the variation in source frequency reduces the performance of input current control. To achieve sinusoidal input current control under the distorted source voltage and frequency condition, this paper proposes a compensation strategy of current reference with the distortion component extracted from the phase angle and a detection strategy of frequency variation from the output of a synchronous reference frame phase-lock loop. The experimental results confirm the validity of the proposed method under the distorted source voltage and frequency condition.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.302-304
• /
• 1996

In this paper, a new algorithm for sensorless speed control of switched reluctance motor (SRM) is proposed. It is based on the measurement of initial rate of change of phase current. The initial rate of rise of phase current mainly depends up on the phase inductance at the time instant when the phase is excited. Therefore, the measurement of initial di/dt permits rotor position estimation, which is used to trigger the next phase. In the proposed technique, there is no need to generate additional current pulses when a phase is not excited. Therefore, this scheme does not introduce the unwanted braking torque. Also, only one current measurement is made every time a phase is excited. This reduces the computational load on the micro-controller and enhances the speed range of the sensorless drive. By using this scheme it is possible to implement the sensorless control of SRM using low cost micro-controller.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권8호
• /
• pp.377-386
• /
• 2005

This paper presents the control algorithm of single-phase hybrid active power filter for the compensation of harmonic current components in nonlinear R-L load with passive active Power filters. To construct two phase system, an imaginary second phase was made. In this proposed method, the new signal which is the delayed through the filtering by the phase-delay property of low-pass filter is used as the secondary phase. Because two-phases have the different phase, the instantaneous calculation of harmonic current is possible. In this paper, a reference voltage is created by multiplying the coefficient k by the compensation current using the rotating reference frame synchronized with the source-frequency, not applying to instantaneous reactive power theory which has been used with the existing fixed reference frames In order to verify the validities of the proposed control methods, experiments are carried out with the prototypes of single-phase hybrid active power filter.

• 한국안전학회지
• /
• 제34권5호
• /
• pp.31-36
• /
• 2019

This study made a testing device to evaluate the distribution board management system. Power was supplied to the testing device using a loading-back method and the voltage applied to it was 440 V at the same turn ratio. When the human body electric shock current is 30 mA, the breaking time is set to be less than 240 ms while 30~45 mA current is flowing. The test result shows that in the case of the R-phase it was measured to be 5.19 Hz (193 ms). And the S-phase and T-phase were perfectly cut off at 5.39 Hz (186 ms) and 5.71 Hz (175 ms), respectively. When the human body electric shock current is 60mA, the breaking time is set to be less than 120 ms while 45~75 mA current is flowing. The test result shows that the R-phase, S-phase, and T-phase were accurately cut off at 8.39 Hz (11 ms), 8.87Hz (113 ms) and 9.69 Hz (103 ms), respectively. When the human body electric shock current is 90 mA, the breaking time is set to be less than 48 ms while 75 mA current is flowing. The test result shows that the R-phase, S-phase, and T-phase were accurately cut off at 19.8 Hz (50.4 ms), 16.9 Hz (59.2 ms), and 17.9 Hz (56.0 ms), respectively. That is, the developed testing device satisfied all the requirements of the distribution board evaluation criteria, and it becomes available for the performance evaluation of the distribution board management system.