• Journal of Advanced Marine Engineering and Technology
• /
• 제30권8호
• /
• pp.901-906
• /
• 2006

In this paper, the power amplifier using active bias circuits for LDMOS(Lateral Diffused Metal Oxide Semiconductor) MRF-21180 is designed and fabricated. According to change the temperature, the gate voltage of LDMOS is controlled by the fabricated active bias circuits which is made of PNP transistor to suppress drain current. The driving amplifier using MRF-21125 and MRF-21060 is made to drive the LDMOS MRF-21180 power amplifier. The variation of current consumption in the fabricated 60 watt power amplifier has an excellent characteristics of less than 0.1 A, whereas a passive biasing circuit dissipates more than 0.5 A. The implemented power amplifier has the gain over 9 dB, the gain flatness of less than $\pm$0.1 dB and input and output return loss of less than -6 dB over the frequency range 2.11 $\sim$ 2.17 GHz. The DC operation point of this power amplifier at temperature variation 0 $^{\circ}C$ to 60 $^{\circ}C$ is fixed by active bias circuit.

• 제어로봇시스템학회논문지
• /
• 제22권6호
• /
• pp.417-423
• /
• 2016

Using a sliding mode controller and observer techniques, this paper presents a robust current controller for a DC motor in the presence of parametric uncertainties. One of the most important issues in the practical application of sliding mode schemes is the chattering phenomenon caused by switching actions. This paper presents a novel sliding mode controller that incorporates an integral control with a sliding mode disturbance observer to attenuate the chattering by reducing the controller/observer switching gains. The proposed sliding mode disturbance observer is designed to estimate a relatively slow varying signal in the equivalent lumped disturbance owing to system uncertainties. Combining the estimated uncertainty with the sliding mode control input, the proposed controller can achieve the control objective by using the relatively low gain of the controller. The proposed disturbance observer does not include the switching control input of the baseline sliding mode controller to reduce the observer switching gain. In the proposed approach, the integral sliding mode control is used to improve the steady state control performance. Comparative computer simulations are carried out to demonstrate the performance of the proposed method. Through the simulation results, the proposed controller realizes the robust performance with reduced current ripples.

• 조명전기설비학회논문지
• /
• 제26권4호
• /
• pp.57-66
• /
• 2012

When typical Z-source DC/AC inverter(ZSI) is operated in high voltage gain area, because of its high duty ratio, voltage and current stress in Z-network of typical ZSI are increased. This paper proposes a new switched trans ZSI(STZSI) with two switched trans cells which consist of one trans and two diodes. To confirm the operation performance of the proposed system, the PSIM simulation is performed for typical ZSI, switched inductor ZSI and the proposed STZSI. Voltage / current stress and transient state characteristics of each method are compared under the condition of DC input voltage 100[V] and output phase voltage 66[Vrms]. As a result, we confirmed that transient state of the proposed STZSI is short compared with the conventional ZSI because the high voltage gain is obtained using the same duty ratio, also a low duty ratio is required for the same output voltage. Finally, we could know the proposed system have low voltage and current stress in Z-network compared with the conventional ZSI.

• 전자공학회논문지
• /
• 제54권2호
• /
• pp.53-57
• /
• 2017

본 논문에서는 의료 기기용 401MHz - 406MHz MedRadio 대역에서 사용하는 저잡음 증폭기를 제안한다. 제안한 저잡음 증폭기는 전류 재사용 gm-boosting 기술을 이용한 공통 게이트 증폭기 구조를 채택하여 기존의 gm-boosted 공통 게이트 증폭기에 비해 동일한 전력소모에서 더 높은 전압 이득과 더 낮은 잡음 지수 특성을 얻었다. 제안한 전류 재사용 gm-boosted 저잡음 증폭기는 $0.13{\mu}m$ CMOS 공정을 사용하여 설계하였고, 22 dB의 전압 이득, 2.95 dB의 잡음 지수, -17 dBm의 IIP3 특성을 보이며, 공급 전압 0.5 V에서 $170{\mu}W$의 전력을 소비한다.

• 한국통신학회논문지
• /
• 제22권4호
• /
• pp.685-695
• /
• 1997

In this paper, a new CMOS continuous-time fully-differential current-mode integrator is proposed as a basic building block of the low-voltage high frequency current-mode active filter. The proposed integrator is composed of the CMOS complementary circuit which can extend transconductance of an integrator. Therefore, the unity gain frequency which is determined by a small-signal transconductance and a MOSFET gate capacitance can be expanded by the complementary transconductance of the proposed integrator. And also the magnitude of pole and zero are increased. The unity gain frequency of the proposed integrator is increased about two times larger than that of the conventional continuous-time fully-differential integrator with NMOS-gm. These results are verified by the small signal analysis and the SPICE simulation. As an application circuit of the proposed fully-differential current-mode integrator, the three-pole Chebyshev lowpass filter is designed using 0.8.$\mu$m CMOS processing parameters. SPICE simulation predicts a 3-dB bandwidth of 148MHz and power dissipation of 4.3mW/pole for the three-pole filter with 3-V power supply.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.726-728
• /
• 2004

In this paper, the gain of the observer is properly set up using the fuzzy control and Fuzzy-Sliding observer(FSQ) that have a superior transient characteristic and is easy to implement compared to the existing method is designed. It estimate the differentiation of the armature current directly using the armature current measured in the AC motor. It estimate the speed of the rotor using the differentiation. It is proposed speed sensorless control method using the estimated speed. Optimal gain of speed observer(Luenberger observer) was set up using the fuzzy control and adapted speed control of AC servo motor. To verify the performance of designed Fuzzy-Sliding observer, simulation compared with fixed speed observer gain of G.B Wang and S.S Peng's sliding observer is performed. Also, it was proved the excellence and feasibility of the proposed observer from the comparison test with a speed sensor and without a speed sensor which used a highly efficient drive and 400W AC servo motor starting system.

• 전기전자학회논문지
• /
• 제14권4호
• /
• pp.257-262
• /
• 2010

본 논문에서는 5.25 GHz에서 넓은 이득 제어범위를 갖는 저전력 가변 이득 프론트-엔드를 설계하였다. 넓은 이득 제어범위를 갖기 위해, 제안된 저잡음 증폭에서는 가변이득 증폭기의 소스에 p-타입 트랜지스터를 연결하였다. 이 방법을 통해 증폭기의 바이어스 전류와 소스 임피던스를 동시에 조절할 수 있었다. 따라서 제안된 저잡음 증폭기는 넓은 이득 제어범위를 갖는다. 믹서에서는 입력 트랜스컨덕턴스단으로 p-타입 트랜지스터를 사용한 폴디드 구조가 제안되었다. 이 구조에서 믹서는 작은 공급 전압에서 각 단에 필요한 만큼의 전류만 흘려주기 때문에 저전력에서도 작동을 할 수 있다. 제안된 프론트-엔드는 최대 33.2 dB의 이득과 17 dB의 넓은 이득 제어범위를 갖는다. 이 때, 잡음지수와 IIP3는 각각 4.8 dB, -8.5 dBm을 갖는다. 이러한 동작을 하는 동안, 제안된 회로는 최대 이득상태에서 7.1 mW, 최소 이득상태에서 2.6 mW의 적은 전력을 소비한다. 시뮬레이션 결과는 TSMC $0.18\;{\mu}m$ CMOS 공정에서 Cadence를 이용하여 얻어졌다.

• 대한전자공학회논문지SD
• /
• 제48권12호
• /
• pp.91-96
• /
• 2011

본 논문에서는 전류 모드 동작에 기반한 IEEE 802.15.4 규격을 만족하는 2.4GHz 저전력 직접 변환 송신기를 제안하고 $0.13{\mu}m$ CMOS 공정을 이용하여 구현하였다. 제안된 송신기는 디지털-아날로그 변환기, 저역통과 필터, 가변 이득 I/Q 상향 혼합기, 구동 증폭기 및 LO 버퍼를 포함하는 주파수 나누기 2회로로 구성되어 있다. 디지털-아날로그 변환기와 저역통과 필터(LPF), 가변이득 I/Q 상향 혼합기의 트랜스컨덕터 단을 하나의 전류 미러 회로로 합친 간단한 구조를 제안하여 전력 소모를 줄이면서 선형성을 향상할 수 있도록 하였다. 구동 증폭기는 캐스코드 타입의 증폭기로 제어 신호를 이용하여 이득을 조절할 수 있게 하였고, 외부 4.8GHz 신호를 받아 주파수 나누기 2 전류 모드 로직 (CML) 회로를 사용하여 2.4GHz I/Q 차동 LO 신호를 생성하도록 설계하였다. 구현한 송신기는 30dB의 이득 조정 범위를 가지면서 0dBm의 최대 출력 신호에서 33dBc의 LO 누설 성분, 40dBc의 3차 하모닉 성분의 특성을 보이며, 구현한 칩의 면적은 $1.76mm{\times}1.26mm$으로 전력소모는 1.2V 단일 전원 전압으로부터 10.2mW이다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 V
• /
• pp.2765-2768
• /
• 2003

The PI controller has many trial-and-error steps for gain design. This paper proposes a new design concept. In this method, a degree of stability and Kharitonov theory are applied and the controller gain is directly expressed by system parameters and current controller's bandwidth. Simulation results for permanent magnetic synchronous motor(PMSM) driving systems confirm the validity of proposed method.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.633-636
• /
• 1998

In this study, power AlGaAs/InGaAs/GaAs PM-HEMT's for mm wave's were fabricated using Electron beam lithography and air-bridge techniques, and so on. DC and AC characteristics of the fabricated power PM-HEMTs were measured under the various bias conditions. For example, DC and RF characteristics such as S21 gain of 3.6 dB at 35 ㎓, current gain cut-off frequencies of 45 ㎓ and maximum oscillation frequencies of 100 ㎓ were carefully analyzed for design methodology of sub-mm wave power devices.