• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.142-149
• /
• 1994

In order to investigate the environmental properties of set net grounds located in the coastal waters of Yeosu. The current in the vicinity of set net grounds was observed by drogue and current meter in 1990 and 1992. The results obtained are summarized as follows: The direction of tidal current at the north enterance of Yeosu bay was southerly in ebb and northwesterly in flood without the distiction of the neap tide and the spring tide. In spring tide the maximum Velocity of the tidal current was 68 cm/sec in ebb and 66 cm/sec in flood. In neap tide the maximum velocity of the tidal current was 37 cm/sec in ebb and 35 cm/sec in flood. And so the direction of residual current was the south ward mainly and 21 cm/sec. The direction of tidal current at set net fishing grounds was southwesterly in ebb and westerly or northwesterly in flood. Regardless of the distinction of neap and spring. The maximum velocity of the current in spring tide was 50 cm/sec in ebb and 40 cm/sec in flood and that in neap was 28 cm/sec in ebb and 25 cm/sec in flood. In spring tide the speed vector along the major axis of semidiurnal tide component was three times as large as diurnal tide. In neap tide, however, the speed vector was about 50% less then that in spring tide, and the semidiurnal tide and diurnal tide were equal in the size of current ellipse and the direction of major axis. The sea area had a southwesterly residual current. 11 cm/sec in spring tide and 7 cm/sec in neap tide. According to the result of drogue tracking, the vicinity of set net fishing ground had a southerly residual current which formed in Yeosu Bay and a weak westerly residual current toward Dolsando from Namhedo. Therefore, set net fishing ground in coastal water of Yeosu was distributed in boundary of inner water which formed from Seamjin river and offshore water supplied from the vicinity of Sorido and Yochido.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.308-312
• /
• 2006

The inductance difference between conducting layers of high-Tc superconducting (HTSC) power transmission cable causes the current sharing of each conducting layer to be unequal, which decreases the current transmission capacity of HTSC power cable. Therefore, the design for even current sharing in HTSC power transmission cable is required. In this paper, we investigated the current distribution of HTSC power cable with a shield layer dependent on the pitch length and the winding direction of each layer. To analyze the effect of the shield layer on the current sharing of the conducting layers of HTSC power cable, the current distribution of HTSC power cable without a shield layer was compared with the case of HTSC power cable with a shield layer. It could be found through the analysis from the computer simulations that the shield layer of HTSC power cable could be contributed to the improvement of current distribution of conducting layers at the specific pitch length and the winding direction of conducting layer. The result and discussion for the current distribution calculated for HTSC power transmission cable with a shield layer were presented and compared with the cable without a shield layer.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.71-72
• /
• 2011

This paper presents a novel and direct dead time compensation method of the 3 phase inverter using space vector pulse width modulation(SVPWM) topology. In the turn on time calculation of the effective voltage, the dead time effect is directly compensated according to the current direction of the midium voltage reference. Since the turn on time of the effective voltage vector is affected by the dead time, the loss time is compensated to turn on time of the effective voltage vector. And the dead time is added to the calculated voltage vector switching times according to the current direction. For the more effective compensation, the direction of the midium phase current is considered by the practical direction and voltage drops in the power devices. The proposed method can compensate the dead time which is considered feedback error or direction of middle phase current without coordinate transform in added controller. The proposed dead time compensation scheme is verified by the computer simulation and experiments of 3 phase R L load.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.159-163
• /
• 2010

The superconducting fault current limiter (SFCL) plays a role in compensating the voltage sag of the sound feeder adjacent to the fault feeder as well as the fault current limiting operation of the fault feeder. Especially, the SFCL using magnetic coupling of two coils with parallel connection has different voltage sag compensating and current limiting characteristics due to the winding direction and the inductance ratio of two coils. In this paper, the current limiting and the voltage sag compensating characteristics of a SFCL using magnetic coupling of parallel connected two coils were analyzed. Through the analysis on the experimental results considering the winding direction of two coils, the SFCL designed with the additive polarity winding was shown to have the higher limited fault current than the SFCL designed with the subtractive polarity winding. In addition, it could be confirmed that the higher fault current limitation of the SFCL could be contributed to the higher load voltage sag compensation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1275-1280
• /
• 2009

Tidal currents were observed at 1 station of artificial reefs group during 15days. Maximum current was 82.4cm/s, and mean current showed 12.8~28.0cm/s, respectively. Flood currents magnitude were bigger than ebb ones due to wake region. To grasp sediment distributions, sediments were sampled at 4-direction(E, W, S, N) around each station. According to the results of sample analysis, sediments showed different distribution by main current direction. It showed that sediments distribution at front and back of artificial reefs were differently occurred by change of main current direction. It suggest that artificial reefs need to install after confirming tidal currents direction and sediments type.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.3 s.14
• /
• pp.1-8
• /
• 2004

In this study, the change of the current in the coastal zone before and after the construction of Jeju new harbor was predicted by using the numerical model, which uses Hardy-Cross method. The numerical model was carried out for the present state, before the construction, and the state after the construction, and for the wave direction the NNW direction for winter and NE direction for summer were tested so that the seasonal change may be considered. The computation result shows that a large amount of the wave induced current was occurred when there were high waves coming in from NNW direction before and after the construction. Also, before the construction a longshore current occurred moving from the west to the east at the new harbor construction site so that it formed a rip current in the Hwabuk-dong front sea. And also, after the construction, the tip current produced changed into nearshore circulating current and a small circulating current appeared at the harbor entrance. On the other hand, at Samyang 4each, which is 3.0km away from the new harbor in the NE direction, shows that there was a longshore current occurred from the west to the east, which is in the opposite direction the new harbor, and the effect on the new harbor by sediment transport at Samyang beach is thought to be very small.

• Journal of Power System Engineering
• /
• v.21 no.5
• /
• pp.20-28
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was performed to investigate the flow fields around the seabed tiller used for soil improvement in coastal fisheries and the pulling force and buoyancy generated by tiller operation. The turbulence model used in this study is a realizable $k-{\varepsilon}$. As a results, at a stationary current or a current speed of 1.2 knots, where rotor rotates in a clockwise direction, a typical vortex pair appears near the tip of the rotor except for the edge, and the strength of the vortex pair increases with the number of revolutions of the rotor. The pulling force of the tiller rotating in the counterclockwise direction increases with the number of revolutions. Also, when the current flows at 1.2 knots and the rotor rotates clockwise, the pulling force of the tiller acts on the upstream side irrespective of the number of rotations of the rotor, so that no force is applied. The buoyancy of the tiller acts on the seawater surface if the flow direction inside the rotor is the same as the direction of rotation of the rotor, regardless of the current velocity, otherwise it acts on the seabed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.5
• /
• pp.491-497
• /
• 2008

The effect of wave and current interactions on jet-like current flowing against waves was investigated based on numerical simulations. The numerical simulations were conducted using a model system of REF/DIF(a wave model) and SHORECIRC(a current model). In the simulations, irregular waves refracted due to the jet-like opposing current were focused along the centerline of current, and the jet-like current was spreaded earlier when the wave heights become larger. The numerical results show that the rapid change of wave height distribution in transverse direction near current inlet plays a significant role to spread the jet-like current. In other words, the radiation stress gradients acting in transverse direction have a more significant effect on the jet-like current than its gradients acting in flowing direction which tend to accelerate the current do. In conclusion, it is indispensible to take into account the interaction between waves and current when the jet-like current such as river mouth meets opposing waves.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.58-59
• /
• 2003

We have developed a simple model allowing further clarifications of the magnetoresistance (MR) contribution to the giant magnetoimpedance (GMI) effect in thin films. The theoretical considerations are the following. It is absolutely assumed that a thin film with no magnetic domain structure and a high frequency ac current I = I$\sub$0/e$\^$iwt/ flowing parallel to the Z direction in the plane of the film. The sample has the thickness 2a in the X direction, thus the Y direction in the plane of the sample and perpendicular to the current direction. The transverse permeability ${\mu}$$\sub$Y/ in the Y direction is uniform. In the case of GMI effect, the total impedance Z = R + iX can be written as.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.812-815
• /
• 2007

To apply the superconducting fault current limiter(SFCL) into a power system, the analysis for its recovery characteristics as well as the consideration for its cooperation with other protecting machine such as a circuit breaker is required. The recovery characteristics of the flux-lock type SFCL like its current limiting characteristics are dependent on the winding direction of two coils. In this paper, the experiments of the current limiting and the recovery characteristics of the flux-lock type SFCL with YBCO thin film were performed. From the analysis on the experimental results due to the winding direction of two coils, the limited fault current in case of the additive polarity winding was observed to be lower than that for the case of the subtractive polarity winding. In addition, the recovery time was found to be faster in case of the additive polarity winding compared to the subtractive polarity winding.