• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권11호
• /
• pp.611-616
• /
• 1999

The introduction of the eddy current braking(ECB) system in HSRT(high speed railway train) is known to be advantageous, in that the system is independent on wheel-rail adhesion coefficient which is greatly affected by weather condition. It also minimize the maintenance of the brake system and does not require any additional electric energy because it is powered form the regenerated power at the time of the braking. In this study, the braking and attraction forces of the ECB are simulated by 2-D FEM and are experimentally verified on a down-scaled prototype. A control algorithm of the ECB is proposed to generate constant braking torque using linear variation of the reference current according to speed. Experimental results shows that the constant torque is generated over all operating speed region by developed control algorithm.

• ETRI Journal
• /
• 제37권6호
• /
• pp.1154-1164
• /
• 2015

This paper proposes a fully sensorless driver for a permanent magnet synchronous motor (PMSM) integrated with a digital motor controller and an analog pre-driver, including sensing circuits and estimators. In the motor controller, a position estimator estimates the back electromotive force and rotor position using a sliding-mode observer. In the pre-driver, drivers for the power devices are designed with a level shifter and isolation technique. In addition, a current sensing circuit measures a three-phase current. All of these circuits are integrated in a single chip such that the driver achieves control of the speed with high accuracy. Using an IC fabricated using a $0.18{\mu}m$ BCDMOS process, the performance was verified experimentally. The driver showed stable operation in spite of the variation in speed and load, a similar efficiency near 1% compared to a commercial driver, a low speed error of about 0.1%, and therefore good performance for the PMSM drive.

• 한국철도학회논문집
• /
• 제13권2호
• /
• pp.166-172
• /
• 2010

현재 전기철도에서는 고성능 유도전동기를 사용하고 있어서 열차속도제어를 위해 벡터제어를 이용하고 있다. 또한 최근에 인버터와 제어이론의 개발로 인해 다양한 방법으로 유도전동기 제어가 가능하다. 현재 유도 전동기를 사용하는 철도차량은 교류전동기를 이용한 역행, 역상제동 및 회생제동 등이 가능하다. 따라서 다양한 방법을 적용하기 위해서는 모터블록과 유도전동기의 모델이 필요하다. 유도전동기의 제어 방법으로는 가변 전압운전, 가변주파수 운전을 통하여 유도전동기의 토크와 회전수를 제어한다. 철도차량 추진시스템은 많은 서브시스템을 가지고 있어 속도제어 성능을 해석하기가 매우 복잡하다. 본 논문에서는 유도전동기를 사용하는 철도차량 추진시스템을 대상으로 Matlab/Simulink를 이용한 속도제어 특성을 분석하였고, 일정시간에 부하에 대한 외란입력응답 특성을 해석하였다. 또한 철도차량 추진시스템의 속도제어 특성을 해석하기 위해 전류, 속도, 자속추정기 및 유도전동기 모델을 제시하였다.

• 대한기계학회논문집A
• /
• 제25권12호
• /
• pp.2078-2090
• /
• 2001

This paper deals with a precise position synchronous control by a cooperative control method of two axes rotating systems. First, the system's dynamics including motor drives described by a motor circuit equation and Newton's kinetic formulation about rotating system. Next, based on conventional PID(Proportional, Integral, Derivative) control law, current and speed controller are designed very simply to follow up reference speed correctly under some disturbances. Also, position synchronous controller designed to minimize position errors according to integration of speed errors between two motors. Then, the proposed control enables the distributed drives by a software control algorithm to behave in a way as if they are mechanically hard coupled in axes. Further, the stabilities and robustness or the proposed system are investigated. Finally, the proposed system presented here is shown to be more precise position synchronous motion than conventional systems through some simulations and experiments.

• 전자공학회논문지B
• /
• 제30B권11호
• /
• pp.37-46
• /
• 1993

Recently, the elimination of speed sensors has been one of the important requirement in vector control systems, because the speed sensor spoil the ruggedness and simplicity of induction motor. This paper proposes sensorless vector control for high performance of induction motor. The proposed vector control scheme is based on a rotor flux and speed which are calculated from the stator voltage and currents with improved flux estimator. The characteristics of vector control employing stator voltage and current generally deteriorate as the speed gets lower acause the calculated rotor flux depends on the stator resistance and it is difficult to calculate rotor flux at low speed of standstill. This new control system is robust with respect to variations of the stator resistance and it makes possible to calculated rotor flux at low speed of standstill. These feature are verified by the simulation results.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권3호
• /
• pp.88-96
• /
• 1995

고속 엘리베이터는 높은 안정성과 제어성이 필요하므로 기동, 정지시에 영 속도를 포함한 정밀 구동이 필요하다. 유도전동기의 정밀 구동을 위하여 사용되어온 벡터 제어 기법은 슬립 주파수 제어에 의한 간접 벡터 제어와 계자편향에 의한 직접벡터 제어의 두가지 종류로 분류할 수 있으며, 직접벡터제어의 경우 전동기 제어 변수의 변화에 강건한 반면에 직접 벡터 제어의 경우 비교적 넓은 속도구간에서 제어가 가능하다는 장점을 가지고 있다. 본 논문에서 토크는 직접 벡터기반으로 제어하고, 지속은 간접 벡터 기반으로 제어함으로써 유도전동기의 과도상태 동작과 시동시 영 속도 부근 및 저속 영역에서의 동작이 보다 강건하도록 개선된 직접토크-간접자속(DTIF, Direct Torque Indirect Flux)제어기를 제시하였다. 3상 유도전동기의 구동을 위하여 제안된 시스템의 수행결과는 시뮬레이션과 실험을 통하여 입증하였으며, 영 속도부근과 저속에서 고속으로의 변환과정은 속도응답에 대한 상전압, 상전류 그리고 DC링크 전류를 비교 측정하여 안정하고 강건한 속도변화가 이루어짐을 확인 할 수 있었다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권12호
• /
• pp.659-663
• /
• 2002

The brake systems of high-speed train are to be equipped with three different brake systems, such as regenerative brake with regenerative feedback in driving car, a pneumatic disc brake, and non-contact linear eddy-current brake(ECB). The regenerative brake and the pneumatic disc brake are acting on the wheels. Their achievable braking force depends on the adhesive coefficient, which is influenced by the weather condition and speed, between the wheel and The linear eddy current brake gets an economical solution in the high-speed train because of the independence of the adhesive coefficient, no maintenance needed. and the good control characteristics. The braking force and the normal force of ECB for korean high-speed train are analysed by the 2D FEM(Finite Element Method). Finally the normal force is compared with the experiential values to verify the analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.73-76
• /
• 2003

This paper proposes a maximum output power control of grid-connected wind power generation system using cage-type induction generators. For generator control, indirect vector control is used, where d-axis current controls the excitation level and q-axis current controls the generator speed. The generated power flows into the utility through the grid-side converter, by which the do link voltage is controlled to be constant and the ac current is controlled in sinusoid and. The generator speed is adjusted according to wind speed for extracting maximum power generation. Experimental results are shown to verify the validity of the proposed scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.203-206
• /
• 1997

DC servo motors are widely used in many industrial fields as actuator of robot and driving power motors of electrical vehicle. Usually in the speed control systems, of motors, speed sensors are required and this fact results in the increased price and operating cost and the limited application of the motors. In this paper, a new speed control method for DC servo motor is proposed. In the scheme, the rotational speed is estimated by the measurement values of the armature voltage and current, instead of measurement by sensor. Optimal control theory is applied to design of the controller in construction of real system. This paper also report on the results of experiments to prove the validity of the proposed method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1111-1113
• /
• 2003

This paper proposes an effective self-turning algorithm based on Artificial Neural Network (ANN) for fuzzy speed control of the indirect vector controlled induction motor. Indirect vector control method divides and controls stator current by the flux and the torque producing current so that the dynamic characteristic of induction motor may be superior. However, if motor parameter changes, the flux current and the torque producing one's coupling happens and deteriorates the dynamic characteristic. The fuzzy speed controller of an induction motor has the robustness over the effect of this parameter variation than a conventional PI speed controller in some degree. This paper improves its adaptability by adding the self-tuning mechanism to the fuzzy controller. For tracking the speed command, its membership functions are adjusted using ANN adaptation mechanism. This adaptability could be embodied by moving the center positions of the membership functions. Proposed self-tuning method has wide adaptability than existent fuzzy controller or PI controller and is proved robust about parameter variation through Matlab/Simulink simulation.