• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1227-1234
• /
• 2008

In this paper is designed a 256-bit synchronous OTP(one-time programmable) memory required in application fields such as automobile appliance power ICs, display ICs, and CMOS image sensors. A 256-bit synchronous memory cell consists of NMOS capacitor as antifuse and access transistor without a high-voltage blocking transistor. A gate bias voltage circuit for the additional blocking transistor is removed since logic supply voltage VDD(=1.5V) and external program voltage VPPE(=5.5V) are used instead of conventional three supply voltages. And loading current of cell to be programmed increases according to RON(on resistance) of the antifuse and process variation in case of the voltage driving without current constraint in programming. Therefore, there is a problem that program voltage can be increased relatively due to resistive voltage drop on supply voltage VPP. And so loading current can be made to flow constantly by using the current driving method instead of the voltage driving counterpart in programming. Therefore, program voltage VPP can be lowered from 5.9V to 5.5V when measurement is done on the manufactured wafer. And the sens amplifier circuit is simplified by using the sens amplifier of clocked inverter type instead of the conventional current sent amplifier. The synchronous OTP of 256 bits is designed with Magnachip $0.13{\mu}m$ CMOS process. The layout area if $298.4{\times}314{\mu}m2$.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.517-520
• /
• 2002

This paper has been studied Operational Amplification Circuit that has high power specification of 90 W is designed. In the input differential amplifier stage, the current source for circuit bias is designed to protect device from high voltage source. the criving state has the voltage gain more than input differential stage. With temperature compensation design, output stage works stable in different to temperature.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.7
• /
• pp.42-49
• /
• 1993

In this paper, switched-capacitor building block presented which are suitable for implementation in GaAs MESFET technology. They include a current source, a gain stage, and an operational amplifier. Switched-capacitor design techniques are discussed that minimize filter sentsitivity to finite gain of the GaAs operational amplifier. Simulation results are presented on third-order elliptic lowpass ladder filter at a sampling rate of 5GHz.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.623-624
• /
• 2006

In this paper, we introduce the design and fabrication of V-band power amplifier MMIC with excellent gain-flatness for IEEE 802.15.3c WPAN system. The V-band power amplifier was designed using ETRI' $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The gains of the each stages of the amplifier were modified to have broadband characteristics of input/output matching for first and fourth stages and get more gains of edge regions of operating frequency range for second and third stages in order to make the gain-flatness of the amplifier excellently for wide band. The performances of the fabricated 60 GHz power amplifier MMIC are operating frequency of $56.25{\sim}62.25\;GHz$, bandwidth of 6 GHz, small signal gain ($S_{21}$) of $16.5{\sim}17.2\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-16{\sim}-9\;dB$, output reflection coefficient ($S_{22}$) of $-16{\sim}-4\;dB$ and output power ($P_{out}$) of 13 dBm. The chip size of the amplifier MMIC was $3.7{\times}1.4mm^2$.

• Journal of Navigation and Port Research
• /
• v.26 no.2
• /
• pp.215-220
• /
• 2002

In this paper, the 100 watt unit ower amplifier using temperature independent biasing for DTV (Digital Television) repeater application is designed and fabricated. The DC operation point of this unit power amplifier at temperature variation from $20^{\circ}C$ to $100^{\circ}C$ is fixed by active bias circuit. The variation of current consumption in the 100 watt unit power amplifier has an excellent characteristics of less than 0.6A. The implemented unit power amplifier has the gain over 12dB, the gain flatness of less than 0.5dB and input and output return, loss of than 15dB over the DTV repeater frequency range (470~806MHz). This unit power amplifier yields intermodulation distortion(IMD) of more than 32dBc at 2MHz offset, which satisfies the IMD at output power of 100 watt (50dBm).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.10 s.352
• /
• pp.90-97
• /
• 2006

We report our research work on the millimeter-wave broadband amplifier integrating the shunt peaking technology with the cascode configuration. The millimeter-wave broadband cascode amplifier on MIMIC technology was designed and fabricated using $0.1{\mu}m\;{\Gamma}-gate$ GaAs PHEMT, CPW, and passive library. The fabricated PHEMT has shown a transconductance of 346.3 mS/mm, a current gain cut off frequency ($f_T$) of 113 GHz, and a maximum oscillation frequency ($f_{max}$) of 180 GHz. To prevent oscillation of designed cascode amplifier, a parallel resistor and capacitor were connected to drain of common-gate device. For expansion of the bandwidth and flatness of the gain, we inserted the short stub into bias circuits and the compensation transmission line between common-source device and common-gate device, and then their lengths were optimized. Also, the input and output stages were designed using the matching method to obtain the broadband characteristic. From the measurement, we could confirm to extend bandwidth and flat gain by integrating the shunt peaking technology with the cascode configuration. The cascode amplifier shows the broadband characteristic from 19 GHz to 53.5 GHz. Also, the average gain of this amplifier is about 6.5 dB over the bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1060-1068
• /
• 2011

In this paper, Current-Mode Class-D(CMCD) RF Power Amplifier(PA) is designed and implemented at 900 MHz. Conventional CMCD PA has output parallel resonator to reconstruct a fundamental frequency component of the output signal. However the resonator can be removed by connecting inverse class-F PAs because even-harmonic components can be removed by CMCD PA's push-pull structure. Using load-pull, inverse class-F PA with GaN transistors is designed, and CMCD PA with the inverse class-F PA is implemented. The CMCD PA has 64.5 % drain efficiency, 34.2 dBm output power. Comparing with the drain efficiency of a CMCD PA with parallel resonator, the CMCD with the inverse class-F technology has 13.6 % improved drain efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.361-366
• /
• 2012

This paper proposes a low power capacitor cross-coupled 5.2 GHz band low noise amplifier(LNA) using the current-reused topology with the TSMC 0.18 ${\mu}m$ CMOS process. The proposed 5.2 GHz band LNA uses a capacitor cross-coupled $g_m$-boosting method for reducing current flow of circuit and a current-reused topology to decrease total power dissipation. The parallel LC networks are used to reduce size of spiral inductors. The simulation results show high gain of 17.4 dB and noise figure(NF) of 2.7 dB for 5.2 GHz.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.10
• /
• pp.1110-1118
• /
• 2012

In this study, for reducing the residual vibration in high speed motion control stage, an improved 5th order polynomial motion profile was developed. When a stage is moving, the current through the motor coils has the same profile of input motion profile of acceleration, therefore the characteristics of the acceleration input profile directly affect on the performance of the amplifier that includes the current control loop. Commonly low cost amplifier and motor has a narrow current control bandwidth, therefore the proposed algorithm was designed based on this practical constraint. Simulation and experimental results showed that the proposed algorithm clearly has low residual vibration characteristics than conventional 5th order polynomial motion profile on the same drive condition.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2114-2117
• /
• 2014

Joint pain is generally a common disorder not only for the old aged people but also for the immunocompromised patients. The present proposed study reveals the presence of inflammatory diseases in joint generally diagnosed by removing synovial fluid and changes in the volume and composition are examined for the presence of WBC and crystals. This study implement a non-invasive approach to identify the changes in joint fluid by measuring the changes in electrical property of the synovial tissue under the influence of electrical current signal with frequency range between 100 kHz to 300 kHz. The response of tissue for the current signal was measured in terms of potential drop across the tissue. The hardware system design consists of input and output sections. The input section which applies current signal to upper limb joint region is made of ICL8038 function generator IC with amplifier and voltage to current converter. The output section picks voltage variation using metal surface electrode, amplifier, ADC, PIC microcontroller and LCD interface. 100 patient inclusive of normal and disease affected patients where examined for upper limb synovial fluid variation and inflammatory diseases were identified.