• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.365-365
• /
• 2010

In this paper, silicon nitride thin films with different silane and ammonia gas ratios were deposited and characterized for the antireflection and passivation layer of high efficiency single crystalline silicon solar cells. As the flow rate of the ammonia gas increased, the refractive index decreased and the band gap increased. Consequently, the transmittance increased due to the higher band gap and the decrease of the defect states which existed for the 1.68 and 1.80 eV in the SiNx films. The reduction in the carrier lifetime of the SiNx films deposited by using a higher $NH_3/SiH_4$ flow ratio was caused by the increase of the interface traps and the defect states in/on the interface between the SiNx and the silicon wafer. The silicon and nitrogen rich films are not suitable for generating both higher carrier lifetimes and transmittance. These results indicate that the band gap and the defect states of the SiNx films should be carefully controlled in order to obtain the maximum efficiency for c-Si solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.334-345
• /
• 2008

컴퓨터의 발달과 더불어 현대사회는 기록하고 보존해야할 정보의 양이 점점 방대해 지고 있다. 그로 인해 자기기록매체처럼 정보를 사용자의 편의에 따라 반복적으로 기록하고 재생할 수 있는 광기록매체에 대한 관심이 증가되고 있다. $Ge_2Sb_2Te_5$(GST)는 기존의 CD-RW나 Floppy Disk(FD)를 대체할 차세대 기록매체로 주목받고 있다. 따라서 본 연구에서는 비정질상과 결정상으로 변하는 성질을 가지고 있는 GST롤 상변화 기록매체로서 이용하기 위해 굴절률을 평가하였다. 시료는 5N의 순도를 갖는 Ge, Sb, Te 물질을 준비하고 조성비에 맞추어서 석영관에 진공 봉입한 후 용융-냉각법으로 벌크를 제작하였고 열증착 방법으로 Si 및 유리 기판위에 1000nm 두께로 박막을 제작하였다. UV-Vis-IR spectrophotometer를 사용하여 반사도와 투과도를 측정하였고 측정한 스펙트럼을 이용하여 Swanepoel method로 굴절률을 계산하였다. 본 연구진이 자체 개발한 계산툴에 실험값을 대입하였고 실험에 의해 얻은 투과도와 계산툴에 의해 얻은 투과도 스펙트럼을 비교하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.248.2-248.2
• /
• 2014

In this study, the optical properties and structural characteristics of gallium nitride (GaN) thin films prepared by radio frequency (RF) magnetron sputtering were investigated. Auger electron and X-ray photoelectron spectra showed that the deposited films consisted mainly of gallium and nitrogen. The presence of oxygen was also observed. The optical bandgap of the GaN films was measured to be approximately 3.31 eV. The value of the refractive index of the GaN films was found to be 2.36 at a wavelength of 633 nm. X-ray diffraction data revealed that the crystalline phase of the deposited GaN films changed from wurtzite to zinc-blende phase upon decreasing the sputtering gas pressure. Along with the phase change, a strong dependence of the microstructure of the GaN films on the sputtering gas pressure was also observed. The microstructure of the GaN films changed from a voided columnar structure having a rough surface to an extremely condensed structure with a very smooth surface morphology as the sputtering gas pressure was reduced. The relationship between the phase and microstructure changes in the GaN films will be discussed.

• Korean Journal of Optics and Photonics
• /
• v.9 no.2
• /
• pp.70-75
• /
• 1998

The ZnS-SiO$_2$ composite films were fabricated by codeposition from two independent sources. The optical properties and microstructures of these composite films were investigated. The refractive indices of the composite films were compared those by Drude's fomula and showed a good agreement. it showed that microstructures of composite films are an armorphous. But microstructures of composite films with ion assisted deposition are changed from an armorphous to crystalline with increasing Zn mole fractions. We designed and fabricated a single layer antireflection coating on the crystalline silicon substrate using the refractive index of the composite films.

• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.95-102
• /
• 2005

Sodium cellulose carbonate (CC-Na) dissolved in $8.5\;wt\%$ NaOH/ZnO (100/2-3, w/w) aqueous solution was spun into some acidic coagulant systems. Diameter of regenerated cellulose fibers obtained was in the range of $15-50\;{\mu}m$. Serrated or circular cross sectional views were obtained by controlling salt concentration or acidity in the acid/salt/water coagulant systems. Velocity ratio of take-up to spinning was controlled up to 4/1 with increasing spinning velocity from 5 to 40 m/min. Skin structure of was developed at lower acidity or higher concentration of coagulants. Fineness, tenacity and elongation of the regenerated cellulose fibers were in the range of 1.5-27 denier, 1.2-2.2 g/d, and $8-11.3\;\%$, respectively. All of CC-Na and cellulose fibers spun from CC-Na exhibited cellulose II crystalline structure. Crystallinity index was increased with increasing take-up speed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.590-590
• /
• 2012

A transparent conducting oxide (TCO) layer was applied in crystalline Si (c-Si) solar cells without use of the conventional SiNx-coating. A high quality indium-tin-oxide (ITO) layer was directly deposited on an emitter layer of a Si wafer. Three different types of emitters were formed by controlling the phosphorous diffusion condition. A light-doped emitter forming a thinner emitter junction showed an improved photoconversion efficiency of 14.1% comparing to 13.2% of a heavy-doped emitter. This was induced by lower recombination within a narrower depletion region of the light-doped emitter. In the aspect of light management, the intermediate refractive index of ITO is effective to reduce the light reflection leading the enhanced carrier generation in a Si absorber. For the electrical aspect, the ITO layer serves as an efficient electrical conductor and thus relieves the burden of high contact resistance of the light-doped emitter. Additionally, the ITO works as a buffer layer of Ag and Si and certainly prevents the shunting problem of Ag penetration into Si emitter region. It discusses an efficient design scheme of TCO-embedded emitter Si solar cells.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.105-110
• /
• 2011

The doping procedure in crystalline silicon solar cell fabrication usually contains oxygen injection during drive-in process and removal of phosphorous silicate glass(PSG). In this paper, we studied the effect of oxygen injection and PSG on conversion efficiency of solar cell. The mono crystalline silicon wafers with $156{\times}156mm^2$, $200{\mu}m$, $0.5-3.0{\Omega}{\cdot}cm$ and p-type were used. After etching $7{\mu}m$ of the surface to form the pyramidal structure, the P(phosphorous) was injected into silicon wafer using diffusion furnace to make the emitter layer. After then, the silicon nitride was deposited by the PECVD with 80 nm thickness and 2.1 refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$880^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Solar cells with four different types were fabricated with/without oxygen injection and PSG removal. Solar cell that injected oxygen during the drive-in process and removed PSG after doping process showed the 17.9 % conversion efficiency which is best in this study. This solar cells showed $35.5mA/cm^2$ of the current density, 632 mV of the open circuit voltage and 79.5 % of the fill factor.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.51-55
• /
• 2011

In this paper, the optimized doping condition of crystalline silicon solar cells with 156 ${\times}$ 156 mm2 area was studied. To optimize the drive-in condition in the doping process, the other conditions except drive-in temperature and time were fixed. After etching 7 ${\mu}m$ of the surface to form the pyramidal structure, the silicon nitride deposited by the PECVD had 75~80 nm thickness and 2 to 2.1 for a refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in $400-425-450-550-850^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Drive-in temperature was changed in range of $828^{\circ}C$ to $860^{\circ}C$ and time was from 3 min to 40 min. The sheet resistance of wafer was fixed to avoid its effect on solar cell. The solar cell fabricated with various conditions showed the similar conversion efficiency of 17.4%. This experimental result showed the drive-in temperatures and times little influence on solar cell characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.593-596
• /
• 1999

This paper presents a process optimization of antireflectiun (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a doble-layer AR(DLAR) coating of MgF$_2$/CeO$_2$, We investigated CeO$_2$ films as an All layer because they hale a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ film deposited at 400 $^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04 % in the wavelengths ranged from 0.4 7m to 1.1 7m. We achieved the efficiencies of solar cells greater than 15% with 3.12 % improvement with DLAR coatings . Further details on MgF$_2$, CeO$_2$ films, and cell fabrication Parameters are presented in this paper.

• Current Photovoltaic Research
• /
• v.6 no.3
• /
• pp.81-85
• /
• 2018

The photovoltaic modules installed in the actual field are affected by various external environments and the electrical performance output value is generally lowered compared to initial output value. The most of photovoltaic modules consists of low iron glass, encapsulant (EVA), back sheet, frame and junction box assembly based on the solar cells. In this paper, the characteristics of encapsulant which is an important constituent material of photovoltaic module were verified by maximum power determination, electro luminescence images, yellowness index measurement, and gel content measurement after ultraviolet (UV) irradiation exposure. The most commonly installed 72 cells crystalline photovoltaic modules were tested after various UV exposure of 0, 15, 30, and $60kWh/m^2$ and compared with the reference module. After UV exposure of $15kWh/m^2$, which is the current international test condition, a small amount of change was observed in yellowness index and electroluminescence, while a gell content rapidly increased. At a cumulative dose of $60kWh/m^2$, which will be a new international test condition in the near future, however, the yellowness index increased sharply and showed the greatest output power drop.