• 한국안전학회지
• /
• 제25권6호
• /
• pp.86-91
• /
• 2010

The purpose of this study is to analyze the damage patterns and metal structure of 3 phase mold transformers collected from places where accidents have occurred. Compared to an oil-immersed transformer, a mold transformer has the advantage of requiring a smaller installation area and can be kept clean, while its disadvantages include the fact that abnormal symptoms of an accident are difficult to discover and its repair is impossible. The capacity of the mold transformers collected from places where accidents have occurred was 200kVA with primary voltages being F23,900V, R22,900V, 21,900V, 20,900V, 19,900V, etc., as well as secondary voltages being 380V, 220V, etc. It was found from the analysis on the diffusion of combustion in the damaged mold transformers that fire occurred first inside the U-phase primary winding and that carbonization and heat were diffused to V-phase and W-phase in V-pattern. In addition, from the analysis on the cross-sectional structure of the metal of the melted high voltage winding using a metallurgical microscope, it was found that the boundary surface, voids, and columnar structure were formed when an interlayer short-circuit had occurred Therefore, even though it is not possible to find the cause for the occurrence of an interlayer short-circuit at the inner side of the primary winding, it is thought that, due to the thermal energy generated when the short-circuit occurred, the heat source was diffused to the upper side and outside, causing a secondary accident.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.75-78
• /
• 2004

Various jet engines (Turbine engine family and RAM Jet engine) have been developed for high speed aircrafts. but their application to hypersonic flight is restricted by principle problems such as increase of total pressure loss and thermal stress. Therefore, the development of next generation propulsion system for hypersonic aircraft is a very important subject in the aerospace engineering field, SCRAM Jet engine based on a key technology, Supersonic Combustion. is supposed as the best choice for the hypersonic flight. Since Supersonic Combustion requires both rapid ignition and stable flame holding within supersonic air stream, much attention have to be given on the mixing state between air stream and fuel flow. However. the wider diffusion of fuel is expected with less total pressure loss in the supersonic air stream. So. in this study the direction of fuel injection is inclined 30 degree to downstream and the total pressure of jet is controlled for lower penetration height than thickness of boundary layer. Under these flow configuration both streams, fuel and supersonic air stream, would not mix enough. To spread fuel wider into supersonic air an aerodynamic force, baroclinic torque, is adopted. Baroclinic torque is generated by a spatial misalignment between pressure gradient (shock wave plane) and density gradient (mixing layer). A wedge is installed in downstream of injector orifice to induce an oblique shock. The schlieren optical visualization from side transparent wall and the total pressure measurement at exit cross section of combustor estimate how mixing is enhanced by the incidence of shock wave into supersonic boundary layer composed by fuel and air. In this study non-combustionable helium gas is injected with total pressure 0.66㎫ instead of flammable fuel to clarify mixing process. Mach number 1.8. total pressure O.5㎫, total temperature 288K are set up for supersonic air stream.

• 한국추진공학회지
• /
• 제6권2호
• /
• pp.37-44
• /
• 2002

액체로켓엔진에 사용되는 2-유체 동축형 분사기의 분무 연소 특성을 수치적으로 해석하였다. 가스 역학적 상호작용에 의한 미립화 및 그에 따른 물리 현상들에 대해 유동에 대한 보존방정식과 이론식들을 적용, 수치화하여 액체 제트의 상태, 제트의 속도, 제트의 붕괴길이, 액적의 크기등을 예측 하였으며, 액체제트 분사공 크기에 따른 미립화의 변화를 고찰하였다. 모델 검증을 위하여 액체 제트의 접촉길이와 액적의 크기를 기존의 실험결과와 비교하였으며, 그 결과 정성적으로 일치함을 나타내었다. 액체 제트의 접촉길이는 분사공의 직경이 증가할수록 짧아지고 액적의 크기도 분사공의 직경이 증가할수록 작아진다. 액체 제트는 박리율 증가에 따른 분무화에 의하여 단면적이 감소되며, 그에 따른 질량유속의 보존과 가스로부터의 운동량 화산에 따라 미립화가 활발해지는 영역으로부터 그 속도가 급속히 증가된다.

• Nuclear Engineering and Technology
• /
• 제53권7호
• /
• pp.2104-2125
• /
• 2021

This paper presents the verification and validation (V&V) of a calculation module for isotope inventory prediction to control the back-end cycle of spent nuclear fuel (SNF). The calculation method presented herein was implemented in a two-step code system of a lattice code STREAM and a nodal diffusion code RAST-K. STREAM generates a cross section and provides the number density information using branch/history depletion branch calculations, whereas RAST-K supplies the power history and three history indices (boron concentration, moderator temperature, and fuel temperature). As its primary feature, this method can directly consider three-dimensional core simulation conditions using history indices of the operating conditions. Therefore, this method reduces the computation time by avoiding a recalculation of the fuel depletion. The module for isotope inventory calculates the number densities using the Lagrange interpolation method and power history correction factors, which are applied to correct the effects of the decay and fission products generated at different power levels. To assess the reliability of the developed code system for back-end cycle analysis, validation study was performed with 58 measured samples of pressurized water reactor (PWR) SNF, and code-to-code comparison was conducted with STREAM-SNF, HELIOS-1.6 and SCALE 5.1. The V&V results presented that the developed code system can provide reasonable results with comparable confidence intervals. As a result, this paper successfully demonstrates that the isotope inventory prediction code system can be used for spent nuclear fuel analysis.

• Animal Bioscience
• /
• 제35권1호
• /
• pp.138-146
• /
• 2022

Objective: The objective of the current study was to investigate the influences of conventional (CO) and deep litter (DE) systems on antimicrobial resistance in fecal Escherichia coli (E. coli). Methods: A cross-sectional study was carried out to detect antimicrobial resistance to E. coli in swine fecal samples in CO and DE systems located in western and northeastern Thailand. Individual rectal swab samples were taken only from healthy pigs. A total of 215 individual and healthy pigs were randomly selected for isolation and antimicrobial susceptibility test of E. coli by the disc diffusion method. The test panel included amoxicillin (AMX), colistin, doxycycline (DOX), enrofloxacin, gentamicin (GEN), kanamycin, neomycin (NEO), and trimethoprim-sulfamethoxazole (SXT). Results: There were significant (p<0.05) lower resistance levels for GEN, NEO, and SXT in the DE farms compared to those in the CO farms. There was a lower number of antimicrobial resistance agents (p<0.001) in the DE farms compared to those in the CO farms. This result was consistent with those in western (p<0.01) and northeastern (p<0.01) Thailand. Overall, antibiograms of AMX-SXT and AMX-DOX-SXT were found in the CO (19.09% and 20.91%, respectively) and the DE (16.19% and 24.76%, respectively) farms. No antimicrobial resistance (5.71%) was found and AMX (13.33%) resistant pigs in the DE farms, whereas the pattern of AMX-GEN-SXT (6.36%) and AMX-DOX-GEN-SXT (11.82%) resistant pigs was found in the CO farms. Conclusion: The DE system for pig farming was superior to conventional pig farming by lowering the resistance level of fecal E. coli to GEN, NEO, and SXT, with decreasing the number of antimicrobial resistance agents and inducing a small proportion of pigs to be free from antimicrobial resistance.

• Journal of Veterinary Science
• /
• 제23권1호
• /
• pp.9.1-9.11
• /
• 2022

Background: Escherichia coli, which causes subclinical or clinical mastitis in cattle, is responsible for transmitting antimicrobial resistance via human consumption of raw milk or raw milk products. Objectives: The objective of this study was to investigate the molecular characteristics of 183 E. coli from bulk tank milk of five different dairy factories in Korea. Methods: The molecular characteristics of E. coli such as serogroup, virulence, antimicrobial resistance, and integron genes were detected using polymerase chain reaction and antimicrobial susceptibility were tested using the disk diffusion test. Results: In the distribution of phylogenetic groups, group D was the most prevalent (59.6%) and followed by group B1 (25.1%). The most predominant serogroup was O173 (15.3%), and a total of 46 different serotypes were detected. The virulence gene found most often was fimH (73.2%), and stx1, fimH, incC, fyuA, and iutA genes were significantly higher in isolates of phylogenetic group B1 compared to phylogenetic groups A, B2, and D (p < 0.05). Among 64 E. coli isolates that showed resistance to at least one antimicrobial, the highest resistance rate was observed for tetracyclines (37.5%). All 18 integron-positive E. coli carried the integron class I (int1) gene, and three different gene cassette arrangements, dfrA12+aadA2 (2 isolates), aac(6')-Ib3+aac(6')-Ib-cr+aadA4 (2 isolates), and dfrA17+aadA5 (1 isolate) were detected. Conclusions: These data suggest that the E. coli from bulk tank milk can be an indicator for dissemination of antimicrobial resistance and virulence factors via cross-contamination.

• 한국미생물·생명공학회지
• /
• 제51권4호
• /
• pp.474-483
• /
• 2023

Members of the genus Streptomyces produce more than 70% of antibiotics. The rise in antibiotic resistance globally enhanced the search for novel species with the ability to produce new bioactive compounds. This study was initiated to investigate different regions in Jordan for previously uncultured and rare Streptomyces species capable of producing novel antimicrobial compounds especially active against bacteria resistant to antibiotics. A total of 191 Streptomyces strains were isolated from 26 soil samples collected from different geographic regions in Jordan. Isolates were characterized based on colony and cellular morphology as well as using 16S rRNA gene sequencing. These isolates were screened for their ability to produce antibiotics by the perpendicular-cross streak method, and then tested by well diffusion method against tested pathogens. Fifty-four isolates showed potential to produce antimicrobial products especially active against resistant bacteria, 20.1% of the isolates showed inhibitory effect against Staphylococcus aureus, 16.9% against clinical MSSA strains, and 18.0% against MRSA: whereas only 4.2% against Esherichia coli, 3.2% against Klebsiella pneumonia, 2.7% against Pseudomonas aeruginosa, and 10.0% against clinical Candida albicans. Three isolates were selected for further identification due to their antibacterial activity against S. aureus, MRSA, and MSSA. These isolates were identified as follows; Streptomyces aburaviensis DSa3, Streptomyces alboniger SAb7 and Streptomyces misionensis ZAb2, based on cultural, biochemical characteristics and molecular analysis of the 16S rRNA.

• Journal of the Korean Wood Science and Technology
• /
• 제46권1호
• /
• pp.73-84
• /
• 2018

최근 들어 늘어나고 있는 도시형 화재 사고와 건축 외장재에 따른 화재 피해 사례의 증가에 따라 난연처리기술의 중요성이 부각되고 있다. 특히, 목재를 기반으로 한 건축재료의 활용에 있어서 난연처리기술은 더욱 중요하게 평가되고 있다. Intumescent 시스템은 비할로겐계 난연처리기술의 하나로, 발포와 탄화층 형성을 통하여 난연성을 구현하는 시스템이다. 본 연구에서는 Intumescent 시스템을 적용하기 위해 Ethylene vinyl acetate (EVA)를 매트릭스로 채용하여 복합재료를 제조하였다. Intumescent 시스템의 난연특성을 강화하기 위해 나노클레이를 함께 적용하였다. Intumescent 시스템과 나노클레이 기술을 함께 적용한 복합재료를 시트상의 시험편으로 가공한 후, 이를 활용하여 표면의 난연특성이 강화된 새로운 구조의 교호집성재를 제작하였다. Intumescent 시스템을 적용한 복합재료의 연소특성 평가에서 최대 열방출량이 효과적으로 감소되는 것을 확인할 수 있었다. 표면에 부착된 구조에 따라 CLT는 두 단계에 걸친 연소 현상이 발생했다. 또한, 심부 연소 과정에서 최대 열방출률이 크게 감소하는 경향을 확인할 수 있었다. 이러한 특성은 목재의 연소과정에 있어 연소 확산지연효과가 있을 것으로 판단된다. 표면단판에 대한 난연처리기술 및 복합재료 적용 최적화 기술을 통해 보다 화재특성이 개선된 CLT 구조체 개발이 가능할 것으로 기대된다.

• Parasites, Hosts and Diseases
• /
• 제26권2호
• /
• pp.73-86
• /
• 1988

간흡충(Clonorchis sinensis)의 조항원(WWA), 정제항원(ABA)의 민감도와 특이도를 비교해 보는 한편, 발육단계별로 충란 항원(EGA)-피낭유충 항원(MEA)-성충 항원(WWA)의 단백질 구성물질의 차이를 SDS-polyacrylamide gel electrophoresis(SDS-PAGE)로 관찰하고 이들 항원의 유용성을 효소면역반응(enzyme-linked immunosorbent assay: ELISA)으로 비교하여 다음과 같은 결과를 얻었다. 간흡충의 조항원으로부터 정제된 항원(ABA)은 항체와 결합한 결합항원(affinity-purified antibody(IgG) binding antigen:ABA)으로서 Ouchterlony 반응으로 간흡충 감염 가토혈청과 4개의 침모대 (WWA는 7개)를 형성하였다. WWA의 major protein들은 분자량 16,300∼18,500 및 28,000∼29,000 dalton의 Polypeptide band였고, ABA는 분자량 18,000∼21,000 및 29,000∼31,000 dalton의 단백질로 다소의 차이를 보였다. ELISA시첩에서 ABA는 WWA에 비해 현저히 민감도가 낮았다. WWA와 ABA에 대한 폐흡충 감염 사람혈청의 ELISA 정사에서 WWA는 Ouchterlony 양성자 8예중 3예에서 교차반응을 나타내었으나 ABA는 교차반응을 나타내지 않았다. 간흡충의 발육단계별 항원 단백질의 분자량 범위는 WWA 11,000∼80,000, MEA 15,000∼100,000, EGA 15,000∼200,000 dalton이었다. 주류원 단백질의 분자량은 EGA는 각각 36,600 (band No. 22), 38,500(No. 20), 64,000(No. 9), 62,000(No. 10), 54,500(No. 11), 53,000(No. 12) dalton, MEA는 각각 65,600(No. 3), 44,700 (No.7), 43,900(No. 8) dalton, WWA는 각각 16,300∼18,500(No. 31-32), 28,000∼29,000(No. 25), 11,000w13,000 (No. 35) 및 31,000(No. 24) dalton이었다. 즉, MEA와 EGA가 WWA보다 고분자의 단백질로 구성되어 있었다. 각 발육단계별 항원의 항원성은 ELISA 반응으로 볼 때 WWA가 가장 높았고, MEA는 약한 항원성만을 나타내었으며 EGA는 음성이었다. WWA와 간흡충 감염 가토혈청은 감염 4∼6주에 OD>1.0, 12주 이후 항체가의 plateau를 나타내었으나 MEA는 Ouchterlony 반응에서 EGA와 함께 음성반응을 보였다. ELISA에서도 중감염군(12∼20주)에서만 OD>0.6으로 미약한 항원성이 인정되었으며 경감염군은 전감염기간중 OD<0.6를 나타내었다. 이상의 결과로 보아 성충 항원이 가장 강력한 함원성 물질을 포함하고 있음이 명백하다고 생각된다. 그러나 성충 조항원은 면역진단에 사용할 겹우 타흡충과의 빈번한 교차반응이 예상되므로 민감도 및 특이도가 높은 정제 항원물질을 분리하는 일이 중요하다고 생각된다.

• 대한치과보철학회지
• /
• 제23권1호
• /
• pp.39-59
• /
• 1985

The purpose of this study was to investigate how gap distances of 0.13mm, 0.15mm, 0.20mm, and 0.30mm affects solder joint strength from gold alloys and nickel-chromium base alloys and to examine the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys. The tensile test specimens were prepared in the split stainless steel mold with a half dumbbell shape 2.5mm in diameter and l2mm in length. 6 pairs of specimens of each gap distance group of gold alloys and nickel-chromium base alloys were made and 48 pairs of all specimens were soldered with solder gold of 666 fineness. All soldered specimens were machined to a uniform diameter and then a tensile load was applied at a cross-head speed of 0.10mm/min using Instron Universal Testing Machine, Model 1115. The fractured specimens at solder gold of solder joint fracture with each gap distance of 0.13mm, 0.15mm, 0.20mm, and 0.30mm were examined under the Scanning Electron Microscope, JSM-35c and the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys was analyzed by Electron Probe Micro Analyzer. The results of this study were obtained as follows: 1. In case of soldering of gold alloys, the tensile strength between gold alloys showed $37.33{\pm}2.52kg/mm^2$ at 0.13, $39.14{\pm}3.35kg/mm^2$ at 0.15mm, $43.76{\pm}2.97kg/mm^2$ at 0.20mm, and $49.18{\pm}4.60kg/mm^2$ at 0.30mm. There was statistically significant difference at each gap distance, and so the greater increase of gap distance showed the greater tensile strength. 2. In case of soldering of nickel-chromium base alloys, the tensile strength between nickel-chromium base alloys showed $34.84{\pm}4.26kg/mm^2$ at 0.13mm, $37.25{\pm}2.49kg/mm^2$ at 0.15mm, $42.91{\pm}4.32kg/mm^2$ at 0.20mm, and $46.93{\pm}4.21kg/mm^2$ at 0.30mm. There was not statistically significant difference only between 0.13mm and 0.15mm and bet ween 0.20 mm and 0.30mm, but generally the greater increase of gap distance showed the greater tensile strength. 3. The greater increase of gap distance shoed less porosities in solder gold at solder joint fracture. 4. In solder gold Au, Cu, Ag, Zn, and Sn were composed and Au and Cu were mostly distributed uniformly. 5. In solder joints of solder gold and gold alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Au, Cu, Ag, Pt, and Pd were composed in gold alloys. Au and Cu of solder gold and gold alloys were mostly distributed uniformly and the diffusion of other elements except Pt and Pd around the solder joint was not almost found. In solder joints of solder gold and nickel-chromium base alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Ni, Cr, and Al were composed in nickel-chromium base alloys. Au and Cu of solder gold and Ni and Cr of nickel-chromium base alloys were mostly distributed uniformly and the diffusion of other elements except Cr around the solder joint was not almost found.