• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.4
• /
• pp.9-14
• /
• 1985

In this research mass of a plane strain two dimensional elastic concrete dam under gravitational and hydrostatic loads is minimized, through shape optimization of the dam cross section. Cross sectional area of the dam is taken as cost function of the optimization problem while constraints on the principal stress distribution and dam thickness are imposed. Shape of the boundary of the model is chosen as design variable. Variational formulation of the optimization problem, the material derivative idea of continuum mechanics, and an adjoint variable method are employed for the shape design sensitivity calculation. Then the gradient projection algorithm is utilized to obtain an optimum design iteratively. Research results fully demonstrate that the theory and procedure adopted are quite efficient and can be applicable to a wide class of practical elastic structural design problems.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.6
• /
• pp.591-602
• /
• 2009

The Compton backscatter technique has been applied to lap-joint in aircraft structure in order to determine mass loss due to exfoliative corrosion of the aluminum alloy sheet skin. The mass loss of each layer has been estimated from Compton backscatter A-scan including the aluminum sheet, the corrosion layer, and the sealant. A Compton backscattering imaging system has been also developed to obtain a cross-sectional profile of corroded lap-splices of aging aircraft using a specially designed slit-type camera. The camera is to focus on a small scattering volume inside the material from which the backscattered photons are collected by a collimated scintillator detector for interpretation of material characteristics. The cross section of the layered structure is scanned by moving the scattering volume through the thickness direction of the specimen. The theoretical model of the Compton scattering based on Boltzmann transport theory is presented for quantitative characterization of exfoliative corrosion through deconvolution procedure using a nonlinear least-square error minimization method. It produces practical information such as location and width of planar corrosion in layered structures of aircraft, which generally cannot be detected by conventional NDE techniques such as the ultrasonic method.

• Structural Engineering and Mechanics
• /
• v.49 no.3
• /
• pp.285-296
• /
• 2014

Material damping affects the dynamic behaviors of engineering structures considerably, but up to till now little research is maintained on influence factors of material damping. Based on the damping-stress function of steel, the material damping of steel beams is obtained by calculating the stress distribution of the beams with an analytical method. Some key influence factors of the material damping, such as boundary condition, amplitude and frequency of excitation, load position as well as the cross-sectional dimension of a steel beam are analyzed respectively. The calculated results show that even in elastic scope, material damping does not remain constant but varies with these influence factors. Although boundary condition affects material damping to some extent, such influence can be neglected when the maximum stress amplitude of the beam is less than the fatigue limit of steel. Exciting frequency, load position and cross-section dimension have great effects on the material damping of the beam which maintain the similar changing trend under different boundary conditions respectively.

• Journal of Korea Water Resources Association
• /
• v.30 no.1
• /
• pp.63-73
• /
• 1997

Finite element model is established for the simulation of groundwater flow due to water curtain around underground oil storage Choleski decomposition method. The symmetric global conductance matrix is solved by vector storage Choleski decomposition method. The model is verified through comparison with the results of electric analogy. For the application of this model to real site, the finite element meshes are constructed according to representative vertical cross and longitudinal sections. In cross-sectional analysis, potential and flow distributions are compared based on the cavern pressure and horizontal water curtain. For longitudinal section, effects between nearly located caverns with or without vertical water curtain are analyzed. These results prove that the established model can be used as a tool for flow analysis around underground caverns.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.3
• /
• pp.9-16
• /
• 2016

This paper discusses a refined model for investigating the micro-mechanical behavior of beam-like structures, which are composed of various elastic moduli and complex geometries varying through the cross-section directions and are also periodically-repeated and heterogeneous along the axial direction. Following the previous work (Lee and Yu, 2011), the original three-dimensional static problem is first formulated in a unified and compact form using the concept of decomposition of the rotation tensor. Taking advantage of the smallness of the cross-sectional dimension-to-length parameter and the micro-to-macro heterogeneity, while also performing homogenization along the dimensional reduction simultaneously, the variational asymptotic method is rigorously used to construct a total energy function, which is asymptotically correct up to the second order. Furthermore, through the transformation procedure based on the pure kinematic relations and the linearized equilibrium equations, a generalized Timoshenko model is systematically established. For the purpose of dealing with realistic and complex geometries and constituent materials at the microscopic level, this present approach is incorporated into a commercial analysis package. A few examples available in literature are used to demonstrate the consistency and efficiency of this proposed model, especially for the structures, in which the effects of transverse shear deformations are significant.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.19-24
• /
• 2012

Barium zirconate exhibits good thermo-chemical stability and proton conduction at high temperatures, but shows poor electron conductivity. Therefore, for high efficiency of hydrogen separation, a very thin and dense Pd-Barium zirconate membrane has to be coated on a porous substrate. A thin and dense Pd-Barium zirconate membrane was successfully synthesized on a porous substrate by means of dual sputtering method. The structural and chemical features of the $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membranes sputtered at $300^{\circ}C$ and $400^{\circ}C$ were investigated by X-ray diffractometry, and it was found that a well-crystallized membrane, Pm-3m space group of $BaZrO_3$, was synthesized. The surface and cross-sectional morphologies of membrane were assessed by SEM (scanning electron microscopy) and TEM(transmission electron microscopy) of the surface and of cross sections. The cross sectional observation of Pd-$BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membrane by dual sputtering shows that the coating is quite dense with columnar structure.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.67-69
• /
• 2016

Recently, cost of rare-earth magnets has been raised, because rare-earth magnets are monopolized and the export is also regulated in China. For this reason, the induction motor is operated without the rare-earth magnets. The efficient development of induction motor is more important for economical scheme. A torque of the induction motor is computed and the correlation between dimension and resistance of the squirrel cage rotor is investigated. Also, the correlation between leakage reactance and torque was analyzed with respect to the same dimension of rotor with different shapes. Therefore, this paper proposes the method of improvement for squirrel cage rotor.

• Cartoon and Animation Studies
• /
• s.33
• /
• pp.271-291
• /
• 2013

Cartoons exhibit contents and images and deliver them to readers by repeating frames. Frames embody the cross sectional factors of space-time, and the repetition of frames makes those cross sectional factors into a continuous flow. The gutter, which exists between frames, takes the role to make the continuous flow link smoothly, and at the beginning stage of the gutter, the operating of the gutter was usually passive by the frame meanings. However, the gutter is not just a medium for linking the frames, but is an efficient participation device for creating new expression methods of cartoon organization. By producing new directing methods for cartoon organization, the distinctive functions of the gutter have been kept alive with cartoon history. The distinctive functions of the gutter can be divided largely into transition function, reminiscence function, speech balloon function, pen function, and decorative function. And those functions perform actively as direct expression method of the gutter. When those functional methods are expressed by the author's intention and the frequency of them is generalized according to described contents, using each author's individual differences can suggest direction for new directing organization of cartoons.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.37-42
• /
• 2000

The comparative study of texture of Al/Ti thin films deposited on low-dielectric polymer and $SiO_2$substrates has been investigated. Fifty-nm-thick Ti films and 500-nm-thick Al-1%Si-0.5%Cu (wt%) films were deposited sequentially onto low-k polymers and $SiO_2$by using a DC magnetron sputtering system. The texture of Al thin film was determined using X-ray diffraction (XRD) theta-2theta ($\theta$-2$\theta$) and rocking curve and the microstructure of Al/Ti films on low-k polymer and $SiO_2$substrates was characterized by cross-sectional transmission electron microscopy (TEM). Both the $\theta$-2$\theta$ method and rocking curve measurement suggest that Al/Ti thin films deposited on $SiO_2$have stronger texture than those deposited on low-k polymer. The texture of Al thin films strongly depended on that of Ti films. Cross-sectional TEM revealed that grains of Ti films on $SiO_2$substrates had grown perpendicular to the substrate, while the grains of Ti alms on SiLK substrates were formed randomly. The lower degree of (111) texture of Al thin films on low-k polymer was due to Ti underlayer.

• Transactions of Materials Processing
• /
• v.14 no.5 s.77
• /
• pp.432-438
• /
• 2005

Among the most of manufacturing process, plastic deformation method offers a significant advantage in productivity and enable mass production with controlled quality and low cost. From the point of view, micro forming is a well suited technology in manufacturing very small metallic parts, in particular for mass production, as they are required in many industrial products. Meanwhile, Al 5083 superplastic alloy with very small grains has a great advantage in achieving micro deformation under low stress due to its relatively low strength at a specific high temperature range. This paper describes the micro formability of Al 5083 superplastic alloy and its application to die forging of micro patterns. Micro formability tests of Al 5083 superplastic alloy were carried out with the specially designed micro forging system by using V-grooved micro dies and pyramidal dies made of (100) silicon. With these dies, micro forging was conducted by varying the applied load, material temperature and forging time The micro formability of Al 5083 superplastic alloy was evaluated by comparing $R_f$ value, where $R_f\;=\;A_f/A_v$ ($A_v$ : cross-sectional area of the flowed metal, $A_v$ : cross sectional area of V-groove). The micro formability of 3 dimensional Patterns was also evaluated using Pyramidal type micro dies.