• 한국도로학회논문집
• /
• 제8권3호
• /
• pp.143-153
• /
• 2006

본 연구는 콘크리트 도로 포장에 복륜 단축, 복륜 복축, 복륜 삼축 등 복륜 다축 하중이 포장의 중앙부와 모서리부에 작용할 때 포장의 응력 분포 및 최대 응력의 차이를 분석하고 이러한 응력의 차이가 콘크리트 탄성계수, 슬래브 두께, 그리고 지반 탄성계수에 따라 어떠한 특성을 갖는지를 분석하기 위하여 수행되었다. 변환영역에서의 해석법을 이용하여 중앙부 하중에 의한 응력을 구하였으며 유한요소법을 이용하여 모서리부 하중에 의한 응력을 구하였다. 여러 가지 변수에 대하여 중앙부 하중에 의한 최대 응력과 모서리부 하중에 의한 최대 응력을 비교하였으며 이러한 최대 응력 비율을 예측할 수 있는 공식을 개발하였다. 이러한 공식을 이용하여 중앙부 하중에 의한 최대 응력에서 모서리부 하중에 의한 최대 응력을 예측하여 최대 응력 비율 예측 공식의 정확성을 검증하였다. 연구결과 중앙부와 모서리부 하중에 의한 콘크리트 포장의 최대 응력 변화 경향은 매우 비슷하였으며 종방향 상의 최대 응력 발생 위치는 일치하였다. 모서리부 하중에 의한 최대 응력을 중앙부 하중에 의한 최대 응력으로 나눈 최대 응력 비율은 하중 축 수가 많아질수록 감소하며, 콘크리트 탄성계수가 증가, 슬래브 두께가 증가, 지반 탄성 계수가 감소, 그리고 하중 접지압이 증가할수록 커지게 된다.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2001년도 춘계학술대회
• /
• pp.311-317
• /
• 2001

The notched Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical strain energy release rates(Gc) from the Charpy impact energy measurements. An Instrumented Charpy Impact tester was used to extract ancillary information concerning fracture properties in addition to total fracture properties and maximum critical loads. The stress intensity factor Kd was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• Journal of Electrical Engineering and Technology
• /
• 제10권2호
• /
• pp.452-464
• /
• 2015

This paper proposes a DC microgrid operational strategy and control method for improved service reliability. The objective is to supply power to as many non-critical loads as possible, while providing an uninterrupted power supply to critical loads. The DC bus signaling method, in which DC voltage is an information carrier, is employed to implement the operational strategy in a decentralized manner. During grid-connected operation, a grid-tied converter balances the power of the microgrid by controlling the DC voltage. All loads are connected to the microgrid, and operate normally. During islanded operation, distributed generators (DGs), a backup generator, or an energy storage system balances the power. However, some non-critical loads may be disconnected from the microgrid to ensure the uninterrupted power supply to critical loads. For enhanced service reliability, disconnected loads can be automatically reconnected if certain conditions are satisfied. Control rules are proposed for all devices, and detailed microgrid operational modes and transition conditions are then discussed. Additionally, methods to determine control parameter settings are proposed. PSCAD/EMTDC simulation results demonstrate the performance and effectiveness of the proposed operational strategy and control method.

• 한국농공학회지
• /
• 제29권3호
• /
• pp.153-162
• /
• 1987

A numerical procedure for the analysis of slender arch buckling problems for uniform dead weight is presented in this paper. Such loading changes in the arch profile. The problem is nonlinear. The numerical procedure is limited to an inextensible analysis and to elastic behavior. Based upon a numerical integration technique developed by Newmark for straight beams, a large deflection bending analysis is combined with small deflection buckling routines to formulate the numerical procedure. The numerical procedure is composed of a combination of the numerical integration and successive approximations procedure. The results obtained in this study are as follows : 1.The critical loads obtained in this study coincide with the results by Austin so that the algorithm developed in this study is verified. 2.The numerical results are converged with good precision when the half arch is divided into 10 segments in both Prime and Quadratic section. 3.The critical loads are decreased as the ratios of rise versus span are increased. 4.The critical loads are increased as the moments of inertia at the ends are increased. 5.The critical loads of Prime section are larger than that of Quadratic section under the same profile conditions.

• Structural Engineering and Mechanics
• /
• 제16권4호
• /
• pp.441-468
• /
• 2003

This paper investigates the structural behavior of modular falsework system under sequential pattern loads. Based on the studies of 25 construction sites, the pattern load sequence modeling is defined as models R (rectangle), L and U. The study focuses on the system critical loads, regions of largest reaction forces, discrepancy between the pattern load and the uniform load, and the warning-system plan. The analysis results show that the critical loads of modular falsework systems with sequential pattern loads are very close to those with the uniform load used in design. The regions of largest reaction forces are smaller than those calculated by the uniform load. However, the regions of largest reaction forces of three models under sequential pattern loads can be considered as the crucial positions of warning-system based on the measured index of loading. The positions of the sensors for the warning-system for these three different models are not identical.

• 한국강구조학회 논문집
• /
• 제17권6호통권79호
• /
• pp.699-705
• /
• 2005

이 논문은 자유단에 집중질량을 갖고 종동력이 작용하는 변단면 캔틸레버 기둥의 임계하중에 관한 연구이다. 기둥의 단면을 중실 직사각형 단면을 갖는 선형 변단면으로 채택하고, Bernoulli-Euler 보 이론에 의한 자유단 집중질량을 갖고 종동력을 받는 소위 Beck 기둥의 자유진동을 지배하는 미분방정식을 유도하였다. 이 미분방정식을 수치해석하여 하중-고유진동수 곡선을 얻고 이로부터 발산임계하중 및 동요임계하중을 산출하였다. 수치해석의 결과로부터 변단면 형태, 경사변수 및 질량비가 임계하중에 미치는 영향을 고찰하였다.

• 한국전산구조공학회논문집
• /
• 제19권1호
• /
• pp.85-92
• /
• 2006

이 논문은 일단고정 타단스프링으로 지지된 변단면 Beck 기둥의 임계하중에 관한 연구이다. 기둥의 변단면을 중실 직사각형 단면을 갖는 선형 변단면으로 채택하고, Bernoulli-Euler보 이론을 이용하여 경사종동력이 작용하는 소위 Beck 기둥의 자유진동을 지배하는 상미분방정식과 경계조건을 유도하였다. 이 미분방정식을 수치해석하여 하중-고유진동수 곡선을 얻고 이로부터 발산임계하중 및 동요임계하중을 산출하였다. 수치해석의 결과로부터 변단면 형태, 경사변수 및 스프링 강성이 임계하중에 미치는 영향을 고찰하였다

• 한국공간구조학회논문집
• /
• 제20권2호
• /
• pp.77-85
• /
• 2020

This paper examined the dynamic instability of a shallow arch according to the response characteristics when nearing critical loads. The frequency changing feathers of the time-domain increasing the loads are analyzed using Fast Fourier Transformation (FFT), while the response signal around the critical loads are analyzed using Hilbert-Huang Transformation (HHT). This study reveals that the models with an arch shape of h = 3 or higher exhibit buckling, which is very sensitive to the asymmetric initial conditions. Also, the critical buckling load increases as the shape increases, with its feather varying depending on the asymmetric initial conditions. Decomposition results show the decrease in predominant frequency before the threshold as the load increases, and the predominant period doubles at the critical level. In the vicinity of the critical level, sections rapidly manifest the displacement increase, with the changes in Instantaneous Frequency (IF) and Instant Energy (IE) becoming apparent.

• Structural Engineering and Mechanics
• /
• 제54권4호
• /
• pp.725-740
• /
• 2015

This study presents critical buckling load optimization of the axially graded layered uniform columns. In the first place, characteristic equations for the critical buckling loads for all boundary conditions are obtained using the transfer matrix method. Then, for each case, square of this equation is taken as a fitness function together with constraints. Due to explicitly unavailable objective function for the critical buckling loads as a function of segment length and volume fraction of the materials, especially for the column structures with higher segment numbers, initially, prescribed value is assumed for it and then the design variables satisfying constraints are searched using Differential Evolution (DE) optimization method coupled with eigen-value routine. For constraint handling, Exterior Penalty Function formulation is adapted to the optimization cycle. Different boundary conditions are considered. The results reveal that maximum increments in the critical buckling loads are attained about 20% for cantilevered and pinned-pinned end conditions and 18% for clamped-clamped case. Finally, the strongest column structure configurations will be determined. The scientific and statistical results confirmed efficiency, reliability and robustness of the Differential Evolution optimization method and it can be used in the similar problems which especially include transcendental functions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.903-906
• /
• 2005

The purpose of this paper is to investigate free vibrations and critical loads of the uniform Beck's columns with a tip spring, carrying a tip mass. The ordinary differential equation governing free vibrations of such Beck's column subjected to a follower force is derived based on the Bernoulli-Euler beam theory. Both the divergence and flutter critical loads are calculated from the load-frequency curves that are obtained by solving the differential equation numerically. The critical loads are presented in the figures as functions of various non-dimensional system parameters such as the mass moment of inertia and spring parameter.