• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.339-345
• /
• 1998

The creep of concrete structures caused by variable stresses is mostly calculated by step-by-step method based on the superposition of creep function. Although most practical application is carried out by this linear assumption, significant deviations between predictions and experiments have been observed when unloading takes place, that is, stress is reduced. The recovery is overestimated. The main purpose of this study is to present the application method of the creep analysis model which is expressed with both creep function and creep recovery function to concrete structures where is expressed with both creep function and creep recovery function to concrete structures where increase or decrease of stress is repeated . To apply two function method to time analysis of concrete structures, this study presents the calculation method of creep strain increment for stress variation. Then, this paper executes the time analysis for an example using suggested method, and compares theses results with the previous analysis values and experimental results.

• 콘크리트학회지
• /
• 제11권1호
• /
• pp.279-288
• /
• 1999

콘크리트 구조물의 크리프해석은 주로 크리프식의 중첩원리에 기초한 방법에 의해 수행되고 있다. 그러나 크리프식의 중첩을 응력이 증가하거나 일정할 경우에는 비교적 정확한 예측이 가능하지만, 응력이 감소하는 경우에는 상당한 오차를 나타낸다. 이것은 지속하중과 응력감소 과정에서 크리프와 관련된 콘크리트의 성질이 변화되므로 크리프 회복을 크리프 식의 중첩으로 정확하게 모사할수 없기 때문이다. 따라서, 본 연구에서는 감소와 증가를 반복하는 응력 이력을 지니는 콘크리트 구조물의 좀더 정확하고 합리적인 장기거동 해석을 위하여 응력의 감소를 단순히 크리프식의 중첩에 의해 해석한 기존의 방법과는 달리 크리프식과 크리프 회복식으로 표현하여, 소위 2함수 방법(two-function method)를 콘크리트구조물의 해석에 적용하는 방법을 제시하였다. 본 연구의 2함수방법을 콘크리트 구조물의 장기거동 해석을 적용하기 위해, 시간단계 동안 다양한 응력 변화에 대하여 크리프 변형도 증분량을 계산하는 방법을 제시하였다. 본 연구의 해석방법에 의해서 해석된 결과를 기존의 크리프식의 중첩에 의한 결과 및 기존의 실험결과들과 비교 분석한 결과, 기존의 중첩법은 실험결과와 많은 차이를 보이고 있으나 본 연구의 해석방법은 실험결과와 잘 맞고 있음을 보여주고 있다. 따라서, 크리프회복식을 이용하는 본 연구의 해석방법은 기존의 크리프식의 중첩방법이나 기존의 설계기준에 비해 변화하는 응력이력 하에서의 콘크리트 구조물의 크리프거동을 더 정확하게 서술할 수 있는 방법으로서 앞으로 설계기준 작성과 실제 구조물 해석에 효율적인 응용이 기대되고 있다.

• 드라이브 ㆍ 컨트롤
• /
• 제18권2호
• /
• pp.46-55
• /
• 2021

A forklift is a powered industrial vehicle used to lift and move materials over short distances. Nowadays, almost all forklifts are equipped with an automatic transmission due to its improved operator comfort and increased productivity. Thanks to marked improvement of transmission control unit equipped with highly-advanced microcontrollers, recently developed automatic transmission for forklift have various auxiliary functions such as creep, auto retardation, and automatic shift with excellent shift quality. This paper deals with the creep function which enables one to maneuver a forklift at the designated low speed by slip control of clutches. The design of creep function was based on four modes of creep operation depending on the status of the operator's shift lever and accelerator pedal. Control algorithms and control parameters for each mode were designed to achieve the desired static and dynamic performance. Vehicle test for the designed creep function was carried out with an independently developed embedded controller. Test results confirmed good creep speed control without speed error at a steady state with a mild shift shock during mode changes by stepping or releasing the accelerator.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.91-97
• /
• 1998

The analysis model is the infinite body consisted of power law creep material containing a rigid inclusion with line crack shape subjected to the arbitrarily directional stress on an infinite boundary. The crack analysis is performed using the complex pseudo-stress function. The strain rate intensity factor is determined in the closed form as new fracture mechanics parmeter which represents the magnitudes of stress and strain rate near the tip in power law creep material.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.2953-2959
• /
• 2021

A new practical modeling of the Norton's power law creep is proposed and implemented to analyze the high temperature behaviors of Alloy 690 SG tube material. In the model, both the stress exponent n and the rate constant B are simply treated as the temperature dependent parameters. Based on the two-step optimization procedure, the temperature function of the rate constant B(T) was determined for the data set of each B value after fixing the stress exponent n value by using the prior optimized function at each temperature. This procedure could significantly reduce the numerical errors when using the power law creep equations. Based on the better description of the steady-state creep rates, the experimental rupture times could also be well predicted by using the Monkman-Grant relationship. Furthermore, the difference in tensile strengths at high temperatures could be very well estimated by assuming the imaginary creep stress related to the given strain rate after correcting the temperature effects on the elastic modulus.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.396-403
• /
• 1991

A solution is presented for the computation of the elastic-creep stresses in a hollow cylinder subjected to nonaxisymmetric temperature distribution. The creep problem is treated by the Maxwell creep model. Laplace transformation is used for reformation of the governing equation of elastic problem and Hooke's law in a function of .gamma. , .theta. , and creep constant. The governing equation is set up using the Airy stress function which leads to the biharmonic equation. The solution is obtained by using Fourer series method and Laplace inverse method used to obtain the stress components which include the variation of time. This solution shows excellent agreement with Lamkin's and Boley & Weiner's solution. The viscoelastic stresses are also obtained for the fuel rob tube subjecting nonaxisymmetric thermal load.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.100-107
• /
• 1999

This paper describes a probabilistic remaining life assessment program for the creep crack growth. The probabilistic life assessment program is developed to increase the reliability of life assessment. The probabilistic life assessment involves some uncertainties, such as, initial crack size, material properties, and loading condition, and a triangle distribution function is used for random variable generation. The resulting information provides the engineer with an assessment of the probability of structural failure as a function of operating time given the uncertainties in the input data. This study forms basis of the probabilistic life assessment technique and will be extended to other damage mechanisms.

• Geomechanics and Engineering
• /
• 제20권6호
• /
• pp.517-525
• /
• 2020

The long-term stability of rock engineering is significantly affected by the time-dependent deformation behavior of rock, which is an important mechanical property of rock for engineering design. Although the hard rocks show small creep deformation, it cannot be ignored under high-stress condition during deep excavation. The inner mechanism of creep is complicated, therefore, it is necessary to investigate the relationship between microscopic creep mechanism and the macro creep behavior of rock. Microscopic numerical modeling of sandstone creep was performed in the investigation. A numerical sandstone sample was generated and Parallel Bond contact and Burger's contact model were assigned to the contacts between particles in DEM simulation. Sensitivity analysis of the microscopic creep parameters was conducted to explore how microscopic parameters affect the macroscopic creep deformation. The results show that the microscopic creep parameters have linear correlations with the corresponding macroscopic creep parameters, whereas the friction coefficient shows power function with peak strength and Young's modulus, respectively. Moreover, the microscopic parameters were calibrated. The creep modeling curve is in good agreement with the verification test result. Finally, the creep curves under one-step loading and multi-step loading were compared. This investigation can act as a helpful reference for modeling rock creep behavior from a microscopic mechanism perspective.

• Steel and Composite Structures
• /
• 제15권2호
• /
• pp.163-173
• /
• 2013

The thermal creep is one of the major factors causing the buckle of steel columns in the fire events. But, few related studies have been reported to evaluate the factors affecting the thermal creep of steel column experimentally or numerically. In this study a series of Fire-resistant steel columns with three different slenderness ratios under a sustained load are tested under a uniform temperature up to six hours in order to evaluate the creep upon three selected factors, temperature, applied load, and column slenderness. Based on experimental results, a proposed creep strain rate model is established as the function of a single parameter of the load ratio of temperature LR(T) to determine the buckling time of steel column due to creep. Furthermore it is found that the creep can be neglected when LR(T) is smaller than 0.77.