• 제목/요약/키워드: crack filler

검색결과 48건 처리시간 0.022초

The Effect of Weld Metal Copper Content on HAZ Cracking in Austenitic Stainless Steel welded with Al-brass

  • Lee, H.W.;Lee, J.S.;Choe, W.H.
    • 대한용접접합학회:학술대회논문집
    • /
    • 대한용접접합학회 2005년도 춘계학술발표대회 개요집
    • /
    • pp.152-154
    • /
    • 2005
  • Austenitic stainless steel has good weldability but is sensitive to hot cracking such as solidification crack and liquation crack. In this study, the specimens of dissimilar metals made between austenitic stainless steel and Al-brass were welded by GTAW process using four different filler metals. Cracks were detected in the heat-affected zone of the stainless steel when welded with CuAl, CuSn and NiCu filler metals, but no cracks were detected a Ni filler metal was used. The cracks propagated along the grain boundary in the heat affected zone near the fusion line to base metal of 316L stainless steel. The cracks were located inside the weld bead with very fine hairline crack. All cracks initiated at the fusion line and moved forward in the base metal. From energy dispersion spectroscopy (EDS), Cu peak was detected only in the crack-opening area.

  • PDF

Fatigue behavior of mechanical structures welded with different filler metal

  • Alioua, Abdelkader;Bouchouicha, Benattou;Zemri, Mokhtar;IMAD, Abdellatif
    • Advances in materials Research
    • /
    • 제6권3호
    • /
    • pp.233-243
    • /
    • 2017
  • This paper describes an investigation on the effect of using three different filler metals on fatigue behavior of mechanical structures welded. The welding is carried out on the steel A510AP used for the manufacture of gas cisterns and pipes. The welding process used is manual welding with coated electrodes and automatic arc welding. Compact tension CT50 specimen has been used. The three zones of welded joint; filler metal FM, heat affected zone HAZ and base metal BM have been investigated. The results show that the crack growth rate CGR is decreasing respectively in BM, FM and HAZ; however, this variation decreases when stress intensity factor SIF increases. For low values of SIF, the CGR is inferior in the over-matched filler metal of which the value of mismatch M is near unity, but for high values of M the CGR is superior, and the effect of the over-matching on CGR becomes negative. No deviation of the crack growth path has been noticed.

IC 몰딩 콤파운드 재료의 파괴 인성치(II) (Fracture Toughness of IC Molding Compound Materials(II))

  • 김경섭;신영의
    • 한국전기전자재료학회논문지
    • /
    • 제11권5호
    • /
    • pp.353-357
    • /
    • 1998
  • Cracking problem of Epoxy Molding Compound(EMC) is critical for the reliability of the plastic package during temperature cycling and IR-reflow condition. Fracture toughness of EMC, which is defined as the resistance of EMC to the crack propagation, is a useful factor in ht estimation of EMC against package crack. Thus, development of EMC having high fracture toughness at a given loading condition would be important for confirming the integrity of package. In this study, toughness of several EMC was measured by varying the test conditions such as temperature, loading speeds, and weight percent of filler in order to quantify the variation of toughness of EMC under various applicable conditions. It was found from the experiments that toughness of all EMC has following trends, i.e., it rapidly decreases over the glass transition temperature, remains almost same or little decreases below $0^{\circ}C$. It decreases with the growth of cross head speed in EMC and the weight percent of filler as the degree of brittleness of EMC increases with the amount of filler content.

  • PDF

충전재가 함유된 단일겹치기 접착 조인트의 열적 특성에 관한 연구 (Thermal Characteristic of the Tubular Single tap Adhesively Bonded Joint bonded with filler containing epoxy adhesive)

  • 김진국;이대길
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2001년도 춘계학술대회논문집A
    • /
    • pp.370-376
    • /
    • 2001
  • When an adhesive joint is exposed to high environmental temperature, the tensile load capability of the adhesive joint decreases because the elastic modulus and failure strength of structural adhesive decrease. The thermo-mechanical properties of structural adhesive can be improved by addition of fillers to the adhesive. In this paper, the elastic modulus and failure strength of adhesives as well as the tensile load capability of tubular single lap adhesive joints were experimentally and theoretically investigated with respect to the volume fraction of filler (alumina) and the environmental temperature. Also the tensile modulus of the fille containing epoxy adhesive was predicted using a new equation which considers filler shape, filler content and environmental temperature. The tensile load capability of the adhesive joint was predicted by using the effective strain obtained from the finite element analysis and a new failure model, from which the relation between the bonding length and the crack length was developed with respect to the volume fraction of filler.

  • PDF

BaO-B2O3-ZnO 결정화 유리계에서 Al2O3 Filler의 첨가에 따른 소결거동 및 물성변화 (Effect of Al2O3 Filler Addition on Sintering Behavior and Physical Characteristics of BaO-B2O3-ZnO Glass Ceramic System)

  • 김빙숙;김영남;임은섭;이준형;김정주
    • 한국세라믹학회지
    • /
    • 제42권2호
    • /
    • pp.110-116
    • /
    • 2005
  • 본 연구는 $BaO-B_{2}O_3-ZnO$계에서 저온소성이 가능한 조성을 탐색하고, 여기에 $Al_{2}O_3$를 filler로 첨가하여 복합체를 제조할 경우의 소결거동과 물성에 미치는 영향을 조사하였다. 이때 첨가하는 알루미나 분체는 입자크기가 서로 다른 두 종류를 이용함으로서 알루미나 입자 크기의 효과도 동시에 조사하였다. 알루미나 첨가량이 증가하는 경우 복합체의 치밀화정도, 유전상수, 열팽창계수, 그리고 경도 값이 감소하였다. 또한 첨가되는 알루미나 입자의 크기가 미세할 경우 그 감소율은 증가되었다. 한편 파괴인성값은 알루비나 첨가량이 많을수록, 알루미나 입자 크기가 작을수록 오히려 증가하였는데 이는 기공과 filler의 crack전파 억제 효과에 의한 것으로 해석하였다.

Flexural analysis of transverse joints of prefabricated T-girder bridge superstructure

  • Kye, Seungkyung;Jung, Hyung-Jo;Park, Sun-Kyu
    • Structural Engineering and Mechanics
    • /
    • 제77권1호
    • /
    • pp.89-102
    • /
    • 2021
  • Rapid construction of prefabricated bridges requires minimizing the field work of precast members and ensuring structural stability and constructability. In this study, we conducted experimental and analytical investigations of transverse joints of prefabricated T-girder bridge superstructures to verify the flexural performance and serviceability. In addition, we conducted parametric studies to identify the joint parameters. The results showed that both the segmented and continuous specimens satisfied the ultimate flexural strength criterion, and the segmented specimen exhibited unified behavior, with the flexural strength corresponding to that of the continuous specimen. The segmented specimens exhibited elastic behavior under service load conditions, and the maximum crack width satisfied the acceptance criteria. The reliability of the finite element model of the joint was verified, and parametric analysis of the convexity of the joint section and the compressive strength of the filler concrete showed that the minimum deflection and crack width occurred at a specific angle. As the strength of the filler concrete increased, the deflection and crack width decreased. However, we confirmed that the reduction in the crack width was hardly observed above a specific strength. Therefore, a design suitable for prefabricated bridges and accelerated construction can be achieved by improving the joint specifications based on the required criteria.

Silica/Carbon Black이 충전된 NR 가황물의 내Crack 및 내Cutting 특성 (Crack and Cutting Resistance Properties of Natural Rubber(NR) Compounds with Silica/Carbon Black Dual Phase Filler)

  • 손우정;조을룡;김원호
    • Elastomers and Composites
    • /
    • 제37권2호
    • /
    • pp.86-98
    • /
    • 2002
  • 본 연구에서는 실리카/카본블랙 혼합사용과 카본블랙 단독 사용의 경우 상온 또는 고온에서의 인장강도(modulus) 및 인열저항성, 내cutting성, 내crack성을 비교 평가하였다. 실리카와 카본블랙의 함량비 및 단계배합 방법을 통해 NR 가황물을 제조하였으며, 충전제의 함량은 60phr로 고정하였고, semi-EV 가황시스템을 적용하여 실험을 실시하였다. 실리카의 분산은 25phr이하일 때 양호하였으며, 실리카/카본블랙의 함량비가 25/35인 경우 인열에너지, 내crack특성, 내cutting특성이 가장 우수하였다. 충전제로써 카본블랙 단독사용과 실리카/카본블랙(25/35) 혼합사용의 경우를 비교해 보면, 열화에 따른 modulus 및 인장강도, 인열에너지는 실리카/카본블랙(25/35)을 사용한 시편이 더 낮은 감소율을 나타내었다. Cutting특성에서는 카본블랙 단독 사용보다는 실리카/카본블랙(25/35) 혼합사용의 경우가 더 높은 cutting 저항성을 나타내었다. 내crack 특성 또한 실리카/카본블랙(25/35)을 혼합사용한 경우가 온도에 따른 더 높은 변형에너지 완화율(Gp)에도 불구하고 더 낮은 크랙성장속도를 나타내었다.

Dynamic response of a laminated hybrid composite cantilever beam with multiple cracks & moving mass

  • Saritprava Sahoo;Sarada Prasad Parida;Pankaj Charan Jena
    • Structural Engineering and Mechanics
    • /
    • 제87권6호
    • /
    • pp.529-540
    • /
    • 2023
  • A novel laminated-hybrid-composite-beam (LHCB) of glass-epoxy infused with flyash and graphene is constructed for this study. The conventional mixture-rule and constitutive-relationship are modified to incorporate filler and lamina orientation. Eringen's non-local-theory is used to include the filler effect. Hamilton's principle based on fifth-order-layer-wise-shear-deformation-theory is applied to formulate the equation of motion. The analogous shear-spring-models for LHCB with multiple-cracks are employed in finite-element-analysis (FEA). Modal-experimentations are conducted (B&K-analyser) and the findings are compared with theoretical and FEA results. In terms of dimensionless relative-natural-frequencies (RNF), the dynamic-response in cantilevered support is investigated for various relative-crack-severities (RCSs) and relative-crack-positions (RCPs). The increase of RCS increases local-flexibility in LHCB thus reductions in RNFs are observed. RCP is found to play an important role, cracks present near the end-support cause an abrupt drop in RNFs. Further, multiple cracks are observed to enhance the nonlinearity of LHCB strength. Introduction of the first to third crack in an intact LHCB results drop of RNFs by 8%, 10%, and 11.5% correspondingly. Also, it is demonstrated that the RNF varies because of the lamina-orientation, and filler addition. For 0° lamina-orientation the RNF is maximum. Similarly, it is studied that the addition of graphene reduces weight and increases the stiffness of LHCB in contrast to the addition of flyash. Additionally, the response of LHCB to moving mass is accessed by appropriately modifying the numerical programs, and it is noted that the successive introduction of the first to ninth crack results in an approximately 40% to 120% increase in the dynamic-amplitude-ratio.

SOLIDIFICATION CRACKING SUSCEPTIBILITY OF

  • Yoon, Jong-Won
    • 대한용접접합학회:학술대회논문집
    • /
    • 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
    • /
    • pp.577-582
    • /
    • 2002
  • The solidification cracking susceptibilities of AI-Mg-Si alloy laser welds were assessed using the self-restraint tapered specimen crack test. The cracking susceptibility of 6061 and 6082 Al-Mg-Si alloy laser welds was substantially reduced when the filler wire containing high Si such as Al-12 wt.% Si (4047A) was used. The amount of eutectic was observed to affect the solidification cracking of Al-Mg-Si alloy laser welds. Abundant eutectic seems to heal the cracking and reduces the cracking susceptibility, while an initial increase in eutectic liquid leads to the increased cracking tendency.

  • PDF

Solidification Cracking Susceptibility of Al-Mg-Si Alloy Laser Welds

  • Yoon, J.W.
    • International Journal of Korean Welding Society
    • /
    • 제2권2호
    • /
    • pp.42-46
    • /
    • 2002
  • The solidification cracking susceptibilities of Al-Mg-Si alloy laser welds were assessed using the self-restraint tapered specimen crack test. The cracking susceptibility of 6061 and 6082 Al-Mg-Si alloy laser welds was substantially reduced when the filler wire containing high Si such as Al-12 wt.% Si (4047A) was used. The amount of eutectic was observed to affect the solidification cracking of Al-Mg-Si alloy laser welds. Abundant eutectic seems to heal the cracking and reduces the cracking susceptibility, while an initial increase in eutectic liquid leads to the increased cracking tendency.

  • PDF