• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.619-619
• /
• 2009

Recently, silica nanostructures are widely used in various applicationary areas such as chemical sensors, biosensors, nano-fillers, markers, catalysts, and as a substrate for quantum dots etc, because of their excellent physical, chemical and optical properties. Additionally, these days, semiconductor silica and silicon with high purity is a key challenge because of their metallurgical grade silicon (MG-Si) exhibit purity of about 99% produced by an arc discharge method with high cast. Tremendous efforts are being paid towards this direction to reduce the cast of high purity silicon for generation of photovoltaic power as a solar cell. In this direction, which contains a small amount of impurities, which can be further purified by acid leaching process. In this regard, initially the low cast rice-husk was cultivated from local rice field and washed well with high purity distilled water and were treated with acid leaching process (1:10 HCl and $H_2O$) to remove the atmospheric dirt and impurity. The acid treated rice-husk was again washed with distilled water and dried in an oven at $60^{\circ}C$. The dried rice-husk was further annealed at different temperatures (620 and $900^{\circ}C$) for the formation of silica nanospheres. The confirmation of silica was observed by the X-ray diffraction pattern and X-ray photoelectron spectroscopy. The morphology of obtained nanostructures were analyzed via Field-emission scanning electron microscope(FE-SEM) and Transmission electron microscopy(TEM) and it reveals that the size of each nanosphares is about 50-60nm. Using the Inductively coupled plasma mass spectrometry(ICP-MS), Silica was analyzed for the amount of impurities.

• Archives of Pharmacal Research
• /
• v.21 no.5
• /
• pp.570-575
• /
• 1998

To develop a cotton derivatives with prolonged antimicrobial activities, homosulfamine (Hs) was coupled to cotton xanthate (CX) via chelate bond in the presence of Cu(II) ion by one- and two-bath processes. In one-bath process, CX was treated with Cu(II)-Hs solution. In two-bath process, CX was treated with Cu(II) ion solution to produce CX-Cu(II) complex, which was isolated and treated in turn with Hs solution. Effects of concentration, Cu(II)/Hs ratio, and pH on the binding of Hs were investigated at $10{\circ}C$ . In one-bath process, binding of hs took place readily with optimum pH around 5-6. the amount of binding increased to give a maximum within 5 min and decreased slowly to establish an equilibrium withhin an hour. In two-bath process, binding of Hs was much lower than that of one-bath process. Release of Hs from CX-Cu(II)-Hs was investigated by batch and flow method. antimicrobial activiteis of CX-Cu(II)-Hs was investigated by batch and flow method. Antimicrobial activities of CX-Cu(II)-Hs were tested against Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa and Escherichia coli and it showed prolonged activity compared to that of free Hs.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.3
• /
• pp.21-25
• /
• 2014

As wireless power transfer (WPT) technology using strongly coupled electromagnetic resonators is a recently explored technique to realize the large power delivery and storage without any cable or wire, this technique is required for diffusion of electric vehicles (EVs) since it makes possible a convenient charging system. Typically, since the normal conducting coils are used as a transmitting coil in the CPT system, there is limited to deliver the large power promptly in the contactless EV charging system. From this reason, we proposed the combination CPT technology with HTS transmitting antenna, it is called as, superconducting contactless power transfer for EV (SUWPT4EV) system. As the HTS coil has an enough current density, it can deliver a mass amount of electric energy in spite of a small scale antenna. The SUCPT4EV system has been expected as a noble option to improve the transfer efficiency of large electric power. Such a system consists of two resonator coils; HTS transmitting antenna (Tx) coil and normal conducting receiver (Rx) coil. Especially, the impedance matching for each resonator is a sensitive and plays an important role to improve transfer efficiency as well as delivery distance. In this study, we examined the improvement of transmission efficiency and properties for HTS and copper antennas, respectively, within 45 cm distance. Thus, we obtained improved transfer efficiency with HTS antenna over 15% compared with copper antenna. In addition, we achieved effective impedance matching conditions between HTS antenna and copper receiver at radio frequency (RF) power of 370 kHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.495-504
• /
• 1996

In this paper, series-fed mirostrip array anteenas with coupling-slots are prposed and their operating characteristics are analyzed based on analyzed based on analytical and experimental results. An accurate analysis method for the slot-coupled feed structure is based on using both circuit coupling between anteenas and full-wave analysis which use travling wave mode and non-traveling wave mode on feed line. The basis functions that used for the numerical analysis bas been determined depending upon the accuracy, convergence properties of the solution, and the computation time:The patch uses 3 EB mode, the slot uses 1PWS mode, and feeders use 5 PWS mode. Series-fed array antennas have been designed, built, and tested in a standing-wave configuration. Using the results of the full-wave analysis, the chebyshev array antennas consisting of 8 elements are designed and fabricated changing the amount excited to each array element by adjusting slot length and by the slot position relative to the feeder. Experiment results show that the series-fed array antenna designed by adjusting the slot position relative to the feeder is superior to that designed by slot length.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.388-394
• /
• 2008

For purpose of anti-static film remaining unchanged in the condition of $160^{\circ}C$, organic solvent, acid and base solution $0.01\sim0.03{\mu}m$ particles of Sb doped tin oxide(ATO) were grafted by 3-Glycidyloxypropyltrimethoxysilane(GPTS) for improving interfere bonding force between ATO and epoxy resin. The particles were dispersed in 2-methoxyethanol with YD-I28(Bisphenol A type epoxy resin, Kukdo chemical) and 1-imidazole as hardener. The anti-static solutions were coated on PI film as thickness of $0.1{\mu}m$. Surface resistivity of anti-static film containing conductive polymer became $10^{12}\Omega/\Box$ after 32 hours in $160^{\circ}C$. The surface resistivity of ATO grafted by GPTS / Epoxy coating layer remained as $10^{7.6}\Omega/\Box$ in $160^{\circ}C$ for 7 days. ATO grafted by GPTS / Epoxy coating layer coated on PI film was dipped in acetone for 7 days. The surface resistivity remained unchanged as $10^{7.6}\Omega/\Box$. The anti-static layer dipped in water solutions containing each KOH 10 wt % and $H_2SO_4$ 2 wt% was ultra-sonicated for 10 minutes per once until 30th. The surface resistance of anti-static layer containing ATO grafted by GPTS remained unchanged.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.109-114
• /
• 2008

A dynamic model has been developed to simulate dynamic operation of a real double-effect absorption chiller. Dynamic behavior of working fluids in main components was modeled in first-order nonlinear differential equations based on heat and mass balances. Mass transport mechanisms among the main components were modeled by valve throttling, 'U' tube overflow and solution sub-cooling. The nonlinear dynamic equations coupled with the subroutines to calculate thermodynamic properties of working fluids were solved by a numerical method. The dynamic performance of the model was compared with the test data of a commercial medium chiller. The model showed a good agreement with the test data except for the first 5,000 seconds during which different flow rates of the weak solution caused some discrepancy. It was found that the chiller dynamics is governed by the inlet temperatures of the cooling water and the chilled water when the heat input to the chiller is relatively constant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.3
• /
• pp.267-274
• /
• 2010

Unlike the structure which has a homogeneous material property, a composite structure is coupled with materials which have different properties, namely, steel and concrete. At actual modeling, the real behavior cannot be predicted without consideration of those material characteristics. Therefore, by putting the interface element between concrete and steel, a slip of steel and concrete is made predictable. Interface element can be used properly not by an ordinary constitutive relation, but by a non-linear constitutive relation considering actual adhesion and slip. A contact surface between plate-shape steel box and concrete is described by using this interface element. Furthermore, because the general 8 node conforming element is inappropriate for describing a bending buckling behavior of steel box, the EAS(Enhanced Assumed Strain) solid-shell element is used to describe a bending behavior of plate-shape steel box.

• Macromolecular Research
• /
• v.13 no.5
• /
• pp.446-452
• /
• 2005

The interactions between the surface of scaffolds and specific cells play an important role in tissue engineering applications. Some cell adhesive ligand peptides including Arg-Gly-Asp (RGD) have been grafted into polymeric scaffolds to improve specific cell attachment. In order to make cell adhesive scaffolds for tissue regeneration, biodegradable nonporous poly(L-lactic acid) (PLLA) films were prepared by using a solvent casting technique with chloroform. The hydrophobic PLLA films were surface-modified by Argon plasma treatment and in situ direct acrylic acid (AA) grafting to get hydrophilic PLLA-g-PAA. The obtained carboxylic groups of PLLA-g-PAA were coupled with the amine groups of Gly-Arg-Asp-Gly (GRDG, control) and GRGD as a ligand peptide to get PLLA-g-GRDG and PLLA-g-GRGD, respectively. The surface properties of the modified PLLA films were examined by various surface analyses. The surface structures of the PLLA films were confirmed by ATR-FTIR and ESCA, whereas the immobilized amounts of the ligand peptides were 138-145 pmol/$cm^2$. The PLLA surfaces were more hydrophilic after AA and/or RGD grafting but their surface morphologies showed still relatively smoothness. Fibroblast adhesion to the PLLA surfaces was improved in the order of PLLA control

• Journal of the Korean Geophysical Society
• /
• v.2 no.2
• /
• pp.123-134
• /
• 1999

Magnetotelluric responses may be affected by strong anisotropy of the high-conductivity layers (HCL) in the upper mantle or lower crust. We have studied two-dimensional anisotropy MT modelling to examine the effect of high anisotropic media. Electrical properties of a homogeneous anisotropic body are defined by a symmetric conductivity tensor and the problem is described by coupled diffusion equation in the frequency domain. In two-dimensional anisotropic environments, diagonal elements of the impedance tensor have higher values than those in isotropic environments. In some cases, TM mode phases reach more than 90°and apparent resistivities decrease for some frequency range because of telluric distortion. GB decomposition may be used to recover regional responses, but can be affected by the regional anisotropic effect. Considering these results, BC87 dataset was interpreted with a modified anisotropic model.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.1
• /
• pp.78-82
• /
• 2014

Power Transformers with more than one secondary winding are not uncommon in industrial applications. But new classes of applications where very large number of independent secondaries are used are becoming popular in controlled converters for medium and high voltage applications. Cascade H-bridge medium voltage drives and Pulse Step Modulation (PSM) based high voltage power supplies are such applications. Regulated high voltage power supplies (Fig. 1) with 35-100 kV, 5-10 MW output range with very fast dynamics (${\mu}S$ order) uses such transformers. Such power supplies are widely used in fusion research. Here series connection of isolated voltage sources with conventional switching semiconductor devices is achieved by large number of separate transformers or by single unit of multi-secondary transformer. Naturally, a transformer having numbers of secondary windings (~40) on single core is the preferred solution due to space and cost considerations. For design and simulation analysis of such a power supply, the model of a multi-secondary transformer poses special problem to any circuit analysis software as many simulation softwares provide transformer models with limited number (3-6) of secondary windings. Multi-Secondary transformer models with 3 different schemes are available. A comparison of test results from a practical Multi-secondary transformer with a simulation model using magnetic component is found to describe the behavior closer to observed test results. Earlier models assumed magnetising inductance in a linear loss less core model although in actual it is saturable core made-up of CRGO steel laminations. This article discusses a more detailed representation of flux coupled magnetic model with saturable core properties to simulate actual transformers very close to its observed parameters in test and actual usage.