• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 1996년도 사용종료 매립지의 안정화 에 관한 국제 세미나
• /
• pp.97-101
• /
• 1996

Municipal and sanitary landfills can pose environmental problems due to leachate, landfill gas md unstable geotechnical properties. Most governmental bodies delay the correction of landfill problems or landfill replacement until a crises stage is reached. The replacement of a landfill is often made difficult due to costly regulatory controls, public opposition to siting and the high cost of closure for the previous landfill unit. Solutions to extending landfill life and capacity Involve waste minimization by recycling, refuse compaction and waste-to-energy incineration. Incineration can reduce the volume of refuse by 50-95%. The largest installed bases of municipal waste Incinerators are located in Japan and the U.S. The volume of waste contained in a landfill can be estimated by load count tabulations, weight-and-volume measurements or a material balance analysis based on the trash profile of user categories. for an existing landfill, core samples may be collected and analyzed for use in a material balance analysis. Newly generated refuse contains approximately 50% of the heating value of coal. However, landfill properties vary significantly due to the waste profile of the contributors and biodegradation due to time and weathering. The volume of the Nanji-do landfill

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권4호
• /
• pp.139-144
• /
• 1999

Based on the recent developments of the reliability-based structural analysis and design as well as the extending knowledge on the probabiliistic characteristics of load and resistances, the probability based design criteria have been successfully developed for many standards. Since the probabilistic characteristics depend highly on the local load and resistances, it is recognized to develop the design criterion compatible with domestic requirements. The existing optimum design methods, which are generally based on the structural theory and certain engineering experience, do not realistically consider the uncertainties of load and resistances and the basic reliability concepts. This study is directed to propose a optimum design based Expected Total Cost Minimization on P.S.C Box Girder Bridge system which could possibly replace optimum design based traditional provisions of the current code, based on the Neldel-Mead Method reliability theory.

• 한국수자원학회논문집
• /
• 제42권9호
• /
• pp.759-771
• /
• 2009

장거리 용수공급 시스템에서 전력비용은 전체 운영비용의 큰 부분을 차지한다. 본 연구는 시간단위의 펌프와 배수지 시스템의 최적 운영계획을 평가하기 위해 동적계획기법에 기초한 방법론을 제시하고 있다. 해석방법은 운영비용 최소화 관점에서 펌프용량 확대를 전제로 현재 가용 펌프의 효율적 운전과 전력요금체계, 시간별 용수수요 추이 그리고 배수지 특성과 송수관로의 제약조건 등을 고려하였다. 이를 위해 적용 가능한 시스템 운영목적과 제약조건이 제시되었고 개발된 방법은 수도권 광역상수도 양주계통의 2개 가압장과 5개 배수지를 대상으로 적용하였다. 적용결과는 펌프 확장의 경우 상당한 수준의 운전비용을 절감할 수 있는 것으로 나타났으며, 이와 같은 방법은 기존 시스템의 최적운영은 물론 생애주기 비용 최소화 측면에서 신규 용수공급 체계의 설계 등에 적절히 활용될 수 있다.

• 대한영양사협회학술지
• /
• 제7권4호
• /
• pp.410-425
• /
• 2001

This study was designed to assess the waste management practices, source-reduction programs and related tasks in elementary school foodservice in Seoul. and Kyonggi Province Areas. A questionnaire mailed to 910 school foodservice managers in Seoul and Kyonggi province: a 202% (N=184) response rate was obtained. About 83.7% of school foodservice managers were responsible for managing solid waste. Most foodservice operations take the responsibility of food waste but not packaging wastes. The average disposal cost per month per person was about 19 won and income was about 35 won. Leftovers were mainly disposed with platewaste. Platewaste was reused for the livestook feed(68.0%), and some platewaste was composted(11.6%). Source reduction programs implemented in half of school foodservice operations were adjustment of portion size', checking the plate waste', 'working with classroom teachers on waste reduction campaign', 'providing information leaflet on food waste minimization', posting education materials, 'classroom instruction about food waste minimization', and 'improving cooking method. According to factor analysis based on importance rating. slid waste management activities of elementary school foodservice operations were divided to 7 dimensions such as communication and cooperation with others', 'employee training', 'product quality control, 'yield control', plate waste control', 'purchasing', and 'public relations'. As a result of Important-Performance Analysis(IPA), sine dimensions such as 'communication and cooperation with others' and 'plate waste control were identified in Focus Here' quardrant area which need more enhanced performance.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권4호
• /
• pp.231-237
• /
• 2006

This paper proposes an effective drive of high intensity discharge (HID) lamp ballast for cars. All control functions of the proposed ballast are implemented using a low-cost single chip microcontroller, PIC16C73 to optimize the total system size and to minimize cost through minimization of total component number. The proposed ballast generates high open-circuit voltage to ignite the lamp and is controlled to supply effectively the power required to shorten warm-up period after the breakdown. The DC-DC converter of the DC-AC converter part of the ballast utilizes the flyback converter topology that can minimize component number. Also, because to more minimize the ballast size, the transformer size must be minimized, for this, PWM (Pulse Width Modulation) pulses are generated with high frequency using the PWM module of the microcontroller. An analysis for this is explained, briefly. As if the operation of the lamp and ballast arrives at steady-state, then the ballast must AC-control the lamp, for this, the microcontroller utilizes the other PWM module. And the part related to the igniter is explained, briefly. It is shown through experimental results that the controller of the proposed ballast has good performance for the HID lamp for cars.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.141-150
• /
• 2012

The present study examines an efficient congestion management system compatible with the evolving environment. The key is to build an information model shared and exchanged for marketbased solutions to alleviate congestion. Traditional methods for congestion management can be classified into two categories, i.e., the centralized scheme and the decentralized scheme, depending on the extent to which the independent system operator (ISO) is involved in market participants' (MPs) activities. Although the centralized scheme is more appropriate for providing reliable system operation and relieving congestion in near real-time, the decentralized scheme is preferred for supporting efficient market operation. The minimum set of information between the ISO and MPs for decentralized scheme is identified: i) congestion-based zone, ii) Power Transfer Distribution Factors, and iii) transmission congestion cost. The mathematical modeling of the proposed information is expressed, considering its process of making effective use of information. Numerical analysis is conducted to demonstrate both cost minimization from the MP perspective and the reliability enhancement from the ISO perspective based on the proposed information exchange scheme.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.75-80
• /
• 2004

Vehicle structures are composed of many substructure connected to one another by various types of mechanical joints. In vehicle engineering it is important to study these connected structures under various dynamic forces for the evaluations of fatigue life and stress concentration exactly. It is difficult to obtain the accurate load history of specified positions because of the errors such as modeling, measurement and etc. In the beginning of design exact load data are actually necessary for the fatigue strength and life analysis to minimize the cost and time of designing. In this paper, the procedure of practical dynamic force determination is developed by the combination of the principal stresses of F. E. Analysis and experiment. Least square pseudo inverse matrix is adopted to obtain in inverse matrix of analyzed stresses matrix. The error minimization method utilizes the inaccurate measured error and the shifting error that the whole data is stiffed over real data. The least square criterion is adopted to avoid these non. Finally, to verify the proposed procedure, a bus is analyzed. This measurement and prediction technology can be extended to the structural modification of any geometric shape in complex structure.

• 한국경영과학회지
• /
• 제18권1호
• /
• pp.79-95
• /
• 1993

MARKAL (MARKet ALlocation) Model, one of the most sophisticated energy technology assessment model is applied to finding the optimum mix of energy sources and evaluating energy technology competitiveness in Korea. The model is capable of handling Multiple Objective Linear Programming to test the related cost minimization and environmental control function. In this paper three environmental regulation scenarios are observed including 10% and 20% reduction of carbon dioxide emission level. For the purpose of establishing the basic data base, Korea Reference Engergy System is also developed on the base of the year 1989 with technology utilization and energy flow analysis.

• Journal of Multimedia Information System
• /
• 제1권1호
• /
• pp.87-93
• /
• 2014

The aim of microscopic image restoration is to recover the image by applying the inverse process of degradation, and the results facilitate automated and improved analysis of the image. In this work, we consider the problem of image restoration as a minimization problem of convex cost function, which consists of a least-squares fitting term and regularization terms with non-negative constraints. The finite step method is proposed to solve this constrained convex optimization problem. We demonstrate the convergence of this method. Efficiency and restoration capability of the proposed method were tested and illustrated through numerical experiments.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1996년도 가을 학술발표회 논문집
• /
• pp.277-287
• /
• 1996

Based on the developments of the reliability-based steel structural analysis and design as well as the extending knowledgy on the probabilitic characteristics of loading and resistance the probability based design criteria have been successful Iy developed for many students. The existing design codes, which are genarally based on the structural theory and certain engineering experience, do not realistically consider the uncertainties of loads and resistance and the basic reliability concepts. It is recognized to develope the design criteria by ETCM(Expected Total cost Minimization). In this study, therefore, the proper probability based design criteria (Optimum load and resistance factor design formats ) has been developed based on the safety levels observed from calibration Iii th existing standards, which applies to the ultimate limit states of steel structural members.