• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.1-7
• /
• 2019

As a unify operational processes of the safety inspection for major national facilities, it is expected that the efficiency and professionalism of the project will be enhanced. Also it is being emphasized that the importance of visual inspection that initially find physical and functional defects in facilities. In this study, we developed an E-PAD-based condition evaluation system to check the safety of the facility to overcome the problems and limitations of the existing inspection method. This system consists of introduction, work list, visual inspection, defect table and so on. It is possible to download the inspection drawings at the site and input the damage information to the drawings and check the evaluation grade. In order to verify the E-PAD based condition evaluation system, the inspection data of 10 sample bridges were inputted into the system and the evaluation results were compared. As a result, it was confirmed that the safety grade calculated from the system and the existing safety grade are the same. The feasibility analysis of the AHP method also showed that the function increased by 10%, cost by 36%, and value by 30% compared to the existing method. Therefore, it is expected to contribute to systematic data and information analysis system for improvement of facility management.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.926-929
• /
• 2014

In Korea MVNO was introduced in 2011 when twenty seven years had passed since Korea Mobile Telecom started mobile phone service in 1984. Whithout having its frequency bands and network facilities MVNO can resell the mobile telecom services to the consumers by purchasing MNO's service. That can bring competition more efffective that can lower communication costs through the alternatives. In the early 2000s, the need for the introduction of the MVNO has been raised already by scholars in Korea. But it wasn't until the late 2000s, rate cuts appeared to be a major policy issue, and in 2011 Korean government begin to try to introduce its own MVNO's. In may 2014, MVNO's mobile communication market share reached 6%, but Korea dose not have a firm system yet. However, if government authorities did not insist 3 mobile telecom companies system and recognize global MVNO flow quickly the national cost would be significantly reduced. In the mean time mobile telecom companies have maintained similar billing system and level of service but competed to attract consumers only. It looks like some level of mutual collision and the government cannot help recognizing the situation but it did not do any effective policy improvement effort and government only levied penalties.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.175-181
• /
• 2019

In the case of a conventional single stage decompression regulator used for large depressurization in the hydrogen fuel cell system of a fuel cell electric vehicle (FCEV), problems can arise, such as pulsation, slow response, hydrogen brittleness, leakage, high weight, and high cost due to high decompression. Most of these problems can be overcome easily using two decompression mechanisms (two-stage structures). In addition, a wide outlet-pressure control range can be secured if an electronic solenoid is applied to the second decompression. Accordingly, it is necessary to improve the precision of the outlet pressure of a two-stage pressure-reducing regulator and develop techniques, such as leakage prevention, durability, light weight, and price reduction. Therefore, to improve the outlet pressure accuracy and prevent leakage, the structural part before and after decompression to improve the air tightness were divided and the analysis was carried out assuming that the valve part was closed (open ratio: 0%) after each initial internal pressure application.

• Journal of Korea Port Economic Association
• /
• v.35 no.1
• /
• pp.139-162
• /
• 2019

In the case of Korea, policy support for shipping companies is limited, and the financial support should address the scale and period of support. Comprehensive measures are needed to boost the chances of reviving the industry. In order to secure competitiveness, the shipping companies need to make continuous efforts, prepare for the future by strengthening environmental regulations, and ensure that they have the ability to be flexible in their responses. The shipbuilding industry witnessed some improvement last year amid severe recession, but reforms are needed to address external and internal structural problems; further, to gain the characteristics of future leading industries, it is necessary to secure core technologies, as well as differentiated and specialized industrial competitiveness among rival countries through joint government intervention and joint R&D investment. Taking these steps will ensure that it has environment-friendly vessels and economic shipbuilding capabilities. The competitiveness of Busan Port should enable the utilization of the geopolitical characteristics of East Asia and contribute to: regional economic revitalization; development of its status as hub port; and securing the position of developed countries in East Asian logistics. For this purpose, it is necessary to establish a strategy to: expand the usability of shipowners/carriers; improve the quality of port operations; improve the portability of the smart system; expand the port of mega-ocean carriers; speed up port operations; and create low-cost ports. The establishment of a network of four countries will also require long-term global linkages. For example, there is a need to establish a logistics network between Eurasia and the European region, which will use the Russian Land Bridge System, as well as that of China.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.5
• /
• pp.475-481
• /
• 2019

A splint is one of assisting devices for the disabled with hemiplegia or contracture and is manually made by an experienced expert. Heated thermoplastic materials are continuously fitted to the affected part. This traditional method has a possible risk of low-temperature burn, quality variance of the splint due to the proficiency of maker. etc. While various approaches has been made using 3D printing technology in order to redeem those disadvantages, they still carry high cost issues with 3D scanners or accuracy issues with manual measurement. This research begins with symmetrical characteristics of human body and focuses on the preliminary study for the possibility of splint manufacturing with 3D printing technology based on geometric characteristics of unaffected arm. 3D right and left forearm models of healthy male adults were created by photogrammetry software and a series of digital images in order to measure the circumference and cross-sectional area of the forearm models at every 20mm from the elbow. The circumference and cross-sectional area showed tolerable levels of differences between both sides within subjects; The circumference and cross-sectional area showed very strong correlations between both sides within subjects. From these findings, the possibility of splint manufacturing with 3D printing technology could be confirmed based on the geometric characteristics of unaffected side.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.3
• /
• pp.347-362
• /
• 2019

Underground excavation using TBM machines has been increasing to reduce complaints caused by noise, vibration, and traffic congestion resulted from the urban underground construction in Korea. However, TBM excavation design and construction still need improvement because those are based on standards of the technologically advanced countries (e.g., Japan, Germany) that do not consider geological environment in Korea at all. Above all, although TBM performance is a main factor determining the TBM machine type, duration and cost of the construction, it is estimated by only using UCS (uniaxial compressive strength) as the ground parameters and it often does not match the actual field conditions. This study was carried out as part of efforts to predict penetration rate suitable for Korean ground conditions. The effective parameters were defined through the correlation analysis between the penetration rate and the geotechnical parameters or TBM performance parameters. The effective parameters were then used as variables of the multiple regression analysis to derive a regression model for predicting TBM penetration rate. As a result, the regression model was estimated by UCS and joint spacing and showed a good agreement with field penetration rate measured during TBM excavation. However, when this model was applied to another site in Korea, the prediction accuracy was slightly reduced. Therefore, in order to overcome the limitation of the regression model, further studies are required to obtain a generalized prediction model which is not restricted by the field conditions.

• KIPS Transactions on Software and Data Engineering
• /
• v.8 no.5
• /
• pp.193-204
• /
• 2019

The explosion of data due to the improvement of sensor technology and computing performance has become the basis for analyzing the situation in the industrial fields, and various attempts to detect events based on such data are increasing recently. In particular, sound signals collected from sensors are used as important information to classify events in various application fields as an advantage of efficiently collecting field information at a relatively low cost. However, the performance of sound-event classification in the field cannot be guaranteed if noise can not be removed. That is, in order to implement a system that can be practically applied, robust performance should be guaranteed even in various noise conditions. In this study, we propose a system that can classify the sound event after generating the enhanced sound signal based on the deep learning algorithm. Especially, to remove noise from the sound signal itself, the enhanced sound data against the noise is generated using SEGAN applied to the GAN with a VAE technique. Then, an end-to-end based sound-event classification system is designed to classify the sound events using the enhanced sound signal as input data of CNN structure without a data conversion process. The performance of the proposed method was verified experimentally using sound data obtained from the industrial field, and the f1 score of 99.29% (railway industry) and 97.80% (livestock industry) was confirmed.

• Journal of the Korean Society for Library and Information Science
• /
• v.55 no.3
• /
• pp.57-77
• /
• 2021

The identity of public libraries in Japan is a social education institution under the 「Social Education Act」 and the 「Library Act」. For these identities, the local government's board of education has operated and managed public libraries, and some have managed by the Management Outsourcing System to public organizations. Then, in 2003, the 「Local Autonomy Act」 was revised to introduce the Designated Manager System in form of administrative disposition, and expanded the scope of application to private institutions and organizations. As of the end of 2018, 18.0% of public libraries introduced the DMS, but the pros and cons surrounding it are sharply opposed. This study outlined the overall status of the DMS and the introduction of public libraries, and critically reviewed major issues. As a result, As a result, there was much controversy over the expected cost reduction, service improvement, employee professionalism, business continuity, and cooperation network establishment when DMS was introduced. The reasons were due to downsizing-based personnel management, contract-oriented employment, short periods of designation, lack of multiple competitive markets, and declining service capabilities of irregular workers. The public library is a knowledge and cultural infrastructure that enhances human values and social dignity based on faithful collection and active service, and is a local public goods that emphasizes non-exclusion and non-competitiveness. Given the increasing number of cases in which public libraries are recently contracting out to cultural foundations in Korea, DMS is not a fire across the river. We need to be wary of the possibility that Japan's unbearable institutional lightness will be applied to public libraries in Korea.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.720-726
• /
• 2019

Recently, research on cost reduction and efficiency improvement of crystalline silicon(c-Si) photovoltaic(PV) module has been conducted. In order to reduce costs, the thickness of solar cell wafers is becoming thinner. If the thickness of the wafer is reduced, cracking of wafer may occur in high temperature processes during the c-Si PV module manufacturing process. To solve this problem, a low temperature process has been proposed. Conductive paste(CP) is used for low temperature processing; it contains Sn57.6Bi0.4Ag component and can be electrically combined with solar cells and ribbons at a melting point of $150^{\circ}C$. Use of CP in the PV module manufacturing process can minimize cracks of solar cells. When CP is applied to solar cells, the output varies with the amount of CP, and so the optimum amount of CP must be found. In this paper, in order to find the optimal CP application amount, we manufactured several c-Si PV modules with different CP amounts. The amount control of CP is fixed at air pressure (500 kPa) and nozzle diameter 22G(outer diameter 0.72Ø, inner 0.42Ø) of dispenser; only speed is controlled. The c-Si PV module output is measured to analyze the difference according to the amount of CP and analyzed by optical microscope and Alpha-step. As the result, the optimum amount of CP is 0.452 ~ 0.544 g on solar cells.

• Korean Journal of Optics and Photonics
• /
• v.33 no.6
• /
• pp.267-274
• /
• 2022

In this paper, we report the design and fabrication of binary diffractive optical elements (DOEs) for random-dot-pattern projection for Schlieren imaging. We selected the binary phase level and a pitch of 10 ㎛ for the DOE, based on cost effectiveness and ease of manufacture. We designed the binary DOE using an iterative Fourier-transform algorithm with binary phase optimization. During initial optimization, we applied a computer-generated pseudorandom dot pattern of uniform intensity as a target pattern, and found significant intensity nonuniformity across the field. Based on the evaluation of the initial optimization, we weighted the target random dot pattern with Gaussian profiles to improve the intensity uniformity, resulting in the improvement of uniformity from 52.7% to 90.8%. We verified the design performance by fabricating the designed binary DOE and a beam projector, to which the same was applied. The verification confirmed that the projector produced over 10,000 random dot patterns over 430 mm × 430 mm at a distance of 5 meters, as designed, but had a slightly less uniformity of 84.5%. The fabrication errors of the DOE, mainly edge blurring and spacing errors, were strong possibilities for the difference.